Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We have a few different ways to do the atomic operations, so split
them out in to different headers rather than bloating atomic.h.
Kernelspace gUSA will take this up to a third implementation.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This updates the SH7619 and SH7206 code for the IPR IRQ changes.
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

gcc 4 for sh changes the names of some compiler intrinsic functions
and adds some additional ones. This patch adds the new ones, and
fixes up various module symbol resolution issues.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Get the landisk board building again..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

When testing the per second interrupt support (RTC_UIE_ON/RTC_UIE_OFF)
of the new RTC system it would die in sh_rtc_interrupt due to a null
ptr dereference. The following gets it working correctly.
Signed-off-by: NJamie Lenehan <lenehan@twibble.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Register the RTC resources for the sh775x subtype so that the new
generic RTC support in drivers/rtc/rtc-sh.c will work.
Signed-off-by: NJamie Lenehan <lenehan@twibble.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds a new defconfig for SE7619 and updates SE7206.
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add a couple of new targets, both for uImage and S-rec generation.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

INIT_WORK() dropped the data arg, so now we have to stash an extra
pointer and backpedal instead.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

In the 64-bit PTE case there's no point in restricting the encoding
to the low bits of the PTE, we can instead bump all of this up to
the high 32 bits and extend PTE_FILE_MAX_BITS to 32, adopting the
same convention used by x86 PAE.

There's a minor discrepency between the number of bits used for the
swap type encoding between 32 and 64-bit PTEs, but this is unlikely
to cause any problem given the extended offset.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix typo in 'EXPERIMENTAL' in config CC_STACKPROTECTOR in arch/x86_64/Kconfig.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make powerpc's __ilog2_u64() take a 64-bit argument.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  AT91 MMC update for 2.6.19
  mmc: Change SDHCI iomem error to a warning
  mmc: fix "prev->state: 2 != TASK_RUNNING??" problem on SD/MMC  card removal
  AT91 MMC 5 : Minor cleanups
  AT91 MMC 4 : Interrupt handler cleanup
  AT91 MMC 3 : Move global mci_clk variable
  AT91 MMC 2 : Use platform resources
  AT91 MMC 1: Pass host structure.

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  [PATCH] smc91x: Kill off excessive versatile hooks.
  [PATCH] myri10ge: update driver version to 1.1.0
  [PATCH] myri10ge: fix big_bytes in case of vlan frames
  [PATCH] myri10ge: Full vlan frame in small_bytes
  [PATCH] myri10ge: drop contiguous skb routines
  [PATCH] myri10ge: switch to page-based skb
  [PATCH] myri10ge: add page-based skb routines
  [PATCH] myri10ge: indentation cleanups
  [PATCH] chelsio: working NAPI
  [PATCH] MACB: Use __raw register access
  [PATCH] MACB: Use struct delayed_work instead of struct work_struct
  [PATCH] ucc_geth: Initialize mdio_lock.
  [PATCH] ucc_geth: compilation error fixes

We should not initialize rootfs before all the core initializers have
run.  So do it as a separate stage just before starting the regular
driver initializers.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

As reported by Andy Whitcroft, at least the SLES9 initrd build process
depends on getting the kernel version from the kernel binary.  It does
that by simply trawling the binary and looking for the signature of the
"linux_banner" string (the string "Linux version " to be exact. Which
is really broken in itself, but whatever..)

That got broken when the string was changed to allow /proc/version to
change the UTS release information dynamically, and "get_kernel_version"
thus returned "%s" (see commit a2ee8649:
"[PATCH] Fix linux banner utsname information").

This just restores "linux_banner" as a static string, which should fix
the version finding.  And /proc/version simply uses a different string.

To avoid wasting even that miniscule amount of memory, the early boot
string should really be marked __initdata, but that just causes the same
bug in SLES9 to re-appear, since it will then find other occurrences of
"Linux version " first.

Cc: Andy Whitcroft <apw@shadowen.org>
Acked-by: NHerbert Poetzl <herbert@13thfloor.at>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Steve Fox <drfickle@us.ibm.com>
Acked-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This looks like a result of too many auto-merges. The
CONFIG_ARCH_VERSATILE case was handled a total of 6 times.
This kills 5 of them.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

--

 drivers/net/smc91x.h |   90 ---------------------------------------------------
 1 file changed, 90 deletions(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update driver version to 1.1.0.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix sizing of big_bytes in the case of vlan frames. The 4
VLAN_HLEN bytes were omitted, leading to sizing the big buffer
4 bytes smaller than it should be.  Due to how rx buffers are
carved from pages, this was harmless for the common (9000, 1500)
byte MTUs, but could lead to data corruption for some MTUs.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Receive full vlan frames into smalls when running with a jumbo MTU.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Drop the old routines that used the physically contigous skb now
that we use the physical pages. And rename myri10ge_page_rx_done()
to myri10ge_rx_done() as it was previously.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Switch to physical page skb, by calling the new page-based
allocation routines and using myri10ge_page_rx_done().
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add physical page skb allocation routines and page based rx_done,
to be used by upcoming patches.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Indentation cleanups to synchronize to our tree which is automatically
indent'ed.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This driver tries to enable/disable NAPI at runtime, but
does so in an unsafe manner, and the NAPI interrupt handling is
a mess. Replace it with a compile time selected NAPI implementation.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Since macb is a chip-internal device, use __raw_readl and
__raw_writel instead of readl/writel. This will perform native-endian
accesses, which is the right thing to do on both AVR32 and ARM devices.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The macb driver calls schedule_delayed_work() and friends, so we need
to use a struct delayed_work along with it. The conversion was
explained by David Howells on lkml Dec 5 2006:

http://lkml.org/lkml/2006/12/5/269Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix compilation failures when building the ucc_geth driver with spinlock
debugging.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver is usable on the newer SAM9 processors so replace all text
references to AT91RM9200 with just AT91.

The controller bug where all the words are byte-swapped is fixed on the
AT91SAM9 processors.  The byte-swapping work-around therefore only needs
to be done if cpu_is_at91rm9200().
[Original patch from Wojtek Kaniewski]

The AT91RM9200 and AT91SAM9260 processors support two MMC/SD slots - the
slot which is connected is now passed via the platform_data and the
correct slot selected in the AT91_MCI_SDCR register.

The driver should not be calling at91_set_gpio_output() since the VCC
pin should have already been configured as an output in the
processor/board setup code.  The driver should call
at91_set_gpio_value().
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some controllers report an invalid iomem size, but seem to work
correctly anyway. Change our current error to just a warning and
hope it doesn't cause too much problems.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Currently on SD/MMC card removal the system exhibits the following message (the platform is ARM Versatile):

    prev->state: 2 != TASK_RUNNING??
    mmcqd/762[CPU#0]: BUG in __schedule at linux-2.6/kernel/sched.c:3826

(akpm: someone tried to fix this, but it's still wrong)
Signed-off-by: NVitaly Wool <vitalywool@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

A number of small cleanups to the AT91RM9200 MMC driver:
 - fix warnings generated by pr_debug().
 - prepend "AT91 MMC:" to printk() messages.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch simplifies the AT91RM9200 MMC interrupt handler code so that
it doesn't re-read the Interrupt Status and Interrupt Mask registers
multiple times.

Also defined AT91_MCI_ERRORS instead of using the hard-coded 0xffff0000.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Move the global 'mci_clk' variable into the local 'at91mci_host'
structure.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Use the I/O base-address and IRQ passed to the driver via the
platform_device resources instead of using hardcoded values.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>