Tg3 normally gets a performance boost by increasing the PCI Maximum Read
Request Size (MRRS) to 4k.  Unfortunately, this is causing some problems
on particular hardware platforms.  This patch removes all code that
modifies the MRRS except for one case.

As part of a solution to fix an internal FIFO problem on the 5719, the
driver artificially capped the MRRS to 2k for the entire 5719, and later
5720, ASIC revs.  This was overly aggressive and only really needed to
be done for the 5719 A0.  In the spirit of the rest of this patch, the
driver will only reprogram the MRRS for this device if the value exceeds
the 2k cap.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the earliest TSO capable devices, TSO was accomplished through
firmware.  The TSO cannot coexist with ASF management firmware though.
The tg3 driver determines whether or not ASF is enabled by calling
tg3_get_eeprom_hw_cfg(), which checks a particular bit of NIC memory.
Commit dabc5c67, entitled "tg3: Move
TSO_CAPABLE assignment", accidentally moved the code that determines
TSO capabilities earlier than the call to tg3_get_eeprom_hw_cfg().  As a
consequence, the driver was attempting to determine TSO capabilities
before it had all the data it needed to make the decision.

This patch fixes the problem by revisiting and reevaluating the decision
after tg3_get_eeprom_hw_cfg() is called.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current SFB double hashing is not fulfilling SFB theory, if two flows
share same rxhash value.

Using skb_flow_dissect() permits to really have better hash dispersion,
and get tunnelling support as well.

Double hashing point was mentioned by Florian Westphal
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a custom flow dissector, use skb_flow_dissect() and
benefit from tunnelling support.

This lack of tunnelling support was mentioned by Dan Siemon.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No functional changes.

This uses the code we factorized in skb_flow_dissect()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We use at least two flow dissectors in network stack, with known
limitations and code duplication.

Introduce skb_flow_dissect() to factorize this, highly inspired from
existing dissector from __skb_get_rxhash()

Note : We extensively use skb_header_pointer(), this permits us to not
touch skb at all.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change comparison order such that the variable will come before the compared value.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix spelling, alignment, empty lines, relocate the is_4_port_mode function, and split bnx2x_link_status_update function.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the MAC test of the 1G port of the BCM57800 to use the UMAC instead of the XMAC.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The populate function will fail in case an unknown external PHY is detected.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables the usage of simpler MDC/MDIO work-around when accessing Warpcore registers.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch contain several fixes for the BCM84833. This PHY is still not in bnx2x production, hence this patch can be considered as enhancement.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Put Warpcore in low power mode in case of fan failure to reduce heat.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a problem when new traffic class is created with 0% BW, the ETS is not conforming.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change BRB to work in per class guaranteed mode and handle cases for BW 0%.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now sk_route_caps is u64, its dangerous to use an integer to store
result of an AND operator. It wont work if NETIF_F_SG is moved on the
upper part of u64.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts the drivers in drivers/net/irda/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The problem: Senders were overriding cwnd values picked during an undo
by calling tcp_moderate_cwnd() in tcp_try_to_open().

The fix: Don't moderate cwnd in tcp_try_to_open() if we're in
TCP_CA_Open, since doing so is generally unnecessary and specifically
would override a DSACK-based undo of a cwnd reduction made in fast
recovery.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, SACK-enabled connections hung around in TCP_CA_Disorder
state while snd_una==high_seq, just waiting to accumulate DSACKs and
hopefully undo a cwnd reduction. This could and did lead to the
following unfortunate scenario: if some incoming ACKs advance snd_una
beyond high_seq then we were setting undo_marker to 0 and moving to
TCP_CA_Open, so if (due to reordering in the ACK return path) we
shortly thereafter received a DSACK then we were no longer able to
undo the cwnd reduction.

The change: Simplify the congestion avoidance state machine by
removing the behavior where SACK-enabled connections hung around in
the TCP_CA_Disorder state just waiting for DSACKs. Instead, when
snd_una advances to high_seq or beyond we typically move to
TCP_CA_Open immediately and allow an undo in either TCP_CA_Open or
TCP_CA_Disorder if we later receive enough DSACKs.

Other patches in this series will provide other changes that are
necessary to fully fix this problem.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bug: When the ACK field is below snd_una (which can happen when
ACKs are reordered), senders ignored DSACKs (preventing undo) and did
not call tcp_fastretrans_alert, so they did not increment
prr_delivered to reflect newly-SACKed sequence ranges, and did not
call tcp_xmit_retransmit_queue, thus passing up chances to send out
more retransmitted and new packets based on any newly-SACKed packets.

The change: When the ACK field is below snd_una (the "old_ack" goto
label), call tcp_fastretrans_alert to allow undo based on any
newly-arrived DSACKs and try to send out more packets based on
newly-SACKed packets.

Other patches in this series will provide other changes that are
necessary to fully fix this problem.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bug: Senders ignored DSACKs after recovery when there were no
outstanding packets (a common scenario for HTTP servers).

The change: when there are no outstanding packets (the "no_queue" goto
label), call tcp_fastretrans_alert() in order to use DSACKs to undo
congestion window reductions.

Other patches in this series will provide other changes that are
necessary to fully fix this problem.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow callers to decide whether an ACK is a duplicate ACK. This is a
prerequisite to allowing fastretrans_alert to be called from new
contexts, such as the no_queue and old_ack code paths, from which we
have extra info that tells us whether an ACK is a dupack.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using vlan 0 and UP 0, vlan header wasn't placed.
Signed-off-by: NAmir Vadai <amirv@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device must be in promiscuous mode or DMAC must be same as the host MAC, or
else packet will be dropped by the HW rx filtering.
Signed-off-by: NAmir Vadai <amirv@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are 2 capability bits for WOL, one for each port.
WOL handlers were looking only on the second bit, regardless of the port.
Signed-off-by: NOren Duer <oren@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moving to regular Completion Queue implementation (not collapsed)
Completion for each transmitted packet is written to new entry.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the MLX4_EN_WOL_DO_MODIFY flag which is defined through enum targets
bit 63, this triggers a "cast truncate bits from constant value
(8000000000000000 becomes 0)" warning from sparse, fix that by using
define instead of enum.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using RSS which takes into account UDP headers is controlled by
a module param, fix the setting of the HW RSS context to align
with that scheme. So far it was uncoditionally allowing hashing
on the UDP headers.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Towards adding RSS support for IB drivers/application who use
the mlx4 HW, make the RSS related definitions global and change
the mlx4_en driver to use them.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NShlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the "ISDN4Linux interface" message from device registration,
where it is emitted for each device, to driver registration, where
it is emitted only once, for consistency with the CAPI variant.
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Documentation/networking/ifenslave.c: In function ‘if_getconfig’:
Documentation/networking/ifenslave.c:508:14: warning: variable ‘mtu’ set but not used [-Wunused-but-set-variable]
Documentation/networking/ifenslave.c:508:6: warning: variable ‘metric’ set but not used [-Wunused-but-set-variable]

The purpose of this function is to simply print out the values
it probes, so...
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tx_fifo_errors are tracked in start_xmit_ for virtio_net, but not
reported in the tallies returned by virtnet_stats().  Return them
as the rx "sub-stats" rx_length_errors and rx_frame_errors are.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rx_msg is defined to have a 1 entry array at the end, so gcc warns:

drivers/net/wireless/ray_cs.c: In function ‘rx_authenticate’:
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2436:3: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2439:15: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2452:16: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2453:18: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/ray_cs.c:2453:32: warning: array subscript is above array bounds [-Warray-bounds]

Use a zero length array and rename to "ray_rx_msg" to make sure we hit all
of the necessary cases.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/wireless/airo.c: In function ‘encapsulate’:
drivers/net/wireless/airo.c:1421:15: warning: array subscript is above array bounds [-Warray-bounds]
drivers/net/wireless/airo.c: In function ‘decapsulate’:
drivers/net/wireless/airo.c:1509:16: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethtool EEPROM read/write support using the eeprom_93cx6
library instead of open-coding the functions.

Depends on eeprom_93cx6 driver getting EEPROM write support.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
[sboyd@codeaurora.org: Removed previous eeprom implementation]
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When device is off it is under power saving mode. Changing the MAC address
in that situation will result in the device not communicating as the first
write to the MAC address register is not executed.
Signed-off-by: NTristram Ha <Tristram.Ha@micrel.com>
[ben@simtec.co.uk: cleaned up header]
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for reading the MAC address from the system registers if there
is an EEPROM present. This involves caching the KS_CCR register for later
use (will also be useful for ETHTOOL support) and adding a print to say
that there is an EEPROM present.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for writing data to EEPROM.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Linux Kernel <linux-kernel@vger.kernel.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some devices need to know if the data is to be output or read, so add a
data direction into the eeprom structure to tell the driver whether the
data line should be driven.

The user in this case is the Micrel KS8851 which has a direction
control for the EEPROM data line and thus needs to know whether
to drive it (writing) or to tristate it for receiving.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>