dpi_init() does not use the pdev argument for anything. Remove it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

FB_OMAP_BOOTLOADER_INIT does not work, and it was only partially
implemented for SDI.

This patch removes support for FB_OMAP_BOOTLOADER_INIT to clean up the
code and to remove any assumptions that FB_OMAP_BOOTLOADER_INIT would
work.

Proper implementation is much more complex, requiring early boot time
register and clock handling to keep the DSS running.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSI PLL output clock names have been made more generic. The clock name
describes what the source of the clock and what clock is used for. Some of
DSI PLL parameters like dividers and DSI PLL source have also been made more
generic.

dsi1_pll_fclk and dsi2_pll_fclk have been changed as dsi_pll_hsdiv_dispc_clk
and dsi_pll_hsdiv_dsi_clk respectively. Also, the hsdividers are now named
regm_dispc and regm_dsi instead of regm3 and regm4.

Functions and macros named on the basis of these clock names have also been
made generic.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Clock source names vary across OMAP2/3 and OMAP4, the clock source enum
names have been made generic in the driver, but for purposes of debugging
and dumping clock sources, it is better to preserve the actual TRM name of
the clock.

Introduce a dss feature function 'dss_feat_get_clk_source_name()' which
returns a string with the TRM clock name for the current OMAP in use. The OMAP
specific name is printed along the generic name within brackets.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The enum members of 'dss_clk_source' have clock source names specific to
OMAP2/3. Change the names to more generic terms such that they now describe
where the clocks come from and what they are used for.

Also, change the enum member names to have "DSS_CLK_SRC" instead of "DSS_SRC"
for more clarity.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The maximum supported frequency for DSS has increased from 173 to 186 Mhz on
OMAP4.

Introduce a dss feature function to get the max_fck to replace DISPC_MAX_FCK
macro.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

enum dss_clock structure is replaced with generic names that
could be used across OMAP2420, 2430, 3xxx, 44xx platforms.
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for DSI is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

Also, vdds_dsi regulator handling is copied to dsi.c, since vdds_dsi regulator is
needed by dpi_init() too. Board files are updated accordingly to add 2 instances of
vdds_dsi regulator.

DSI platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for VENC is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

Also, venc_vdda_dac reading is moved to venc.c.

VENC platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for DISPC is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

DISPC platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for RFBI is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

RFBI platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

All clock management is moved to dss platform driver. clk_get/put APIs use
dss device instead of core platform device.

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So the device name is changed from omapdss to omapdss_dss in 2420, 2430,
3xxx clock database files. Now the core driver "omapdss" only takes care
of panel registration with the custom bus.
core driver also uses the clk_enable() / clk_disable() APIs exposed by DSS for
clock management.
DSS driver would do clock management of clocks needed by DISPC, RFBI, DSI, VENC

TODO:  The clock content would be adapted to omap_hwmod in a seperate series.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver of DSS is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.

DSS platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

A panel connects to one of the overlay managers of DSS through some interface block.
On OMAP4, specifying the type of the display is not sufficient to conclude which manager
the panel should be connected to.
Hence, a new member 'channel' is introduced in omap_dss_device structure to determine
which manager the panel uses. The dss_recheck_connections() called in dss_driver_probe()
uses this channel parameter to set the correct manager to the corresponding omap_dss_device.

The channel parameter is used only once to ensure the correct managers are set for each
panel. The parameter dssdev->manager->id will take care of ensuring that the panel and
then the interface driver configures the correct DISPC channel.

Also, add a new Overlay Manager in manager.c, make other changes needed for LCD2 channel.
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NMukund Mittal <mmittal@ti.com>
Signed-off-by: NSamreen <samreen@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The following dispc functions are also changed to incorporate channel as an argument:
	-dispc_lclk_rate()
	-dispc_pclk_rate()
	-dispc_set_pol_freq()
	-dispc_set_clock_div()
	-dispc_get_clock_div()
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NMukund Mittal <mmittal@ti.com>
Signed-off-by: NSamreen <samreen@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
[tomi.valkeinen@nokia.com: fixed trivial compile error]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The interface drivers (dsi.c, sdi.c etc) need to call dispc functions with
dssdev->manager->id as a parameter to specify the DISPC channel which they want
to configure/use, this is required as the same functions are now used to configure
dispc registers of different channels.

The following dispc functions are changed to incorporate channel as an argument:
	-dispc_enable_fifohandcheck()
	-dispc_set_lcd_size()
	-dispc_set_parallel_interface_mode()
	-dispc_set_tft_data_lines()
	-dispc_set_lcd_display_type()
	-dispc_set_lcd_timings()
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NMukund Mittal <mmittal@ti.com>
Signed-off-by: NSamreen <samreen@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
[tomi.valkeinen@nokia.com: fixed trivial compile error]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Enable dss to process color formats with pre-mulitplied alpha.
With this we can have alpha values defined for each pixel
and hence can have different blending values for each pixel.
sysfs entry has been created for this and pre-multiplied alpha
support is turned off by default.
Signed-off-by: NSudeep Basavaraj <sudeep.basavaraj@ti.com>
Signed-off-by: NRajkumar N <rajkumar.nagarajan@ti.com>
Signed-off-by: NSamreen <samreen@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Currently the update area on manual update displays is automatically
enlargened to fully cover scaled overlays. This patch makes that
optional, allowing the panel driver to choose if it's used or not.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The TRM tells us to wait for the DSI PLL derived clocks to become
active before selecting them for use. I didn't actually have any issues
which this would fix but according to the TRM it seems to be the right
thing to do.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move a number of #ifdefs from code into dss.h and elsewhere, and
conditionally define no-op static inline functions, cleaning up the
code. This style is according to Documentation/SubmittingPatches.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Move enable/disable_channel() from omap_dss_device to overlay manager.

This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

dss_select_clk_source() was rather confusing. Selecting the source with
enums is much clearer.

The clk source selection is also stored into memory, so that we know what
is the selected source, even when clocks are off. This is important during
setup, as we need to what clocks to turn on before the clocks are turned
on.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

It looks like on OMAP3 some DSS pins need VDDS_DSI to function properly.

This has not been confirmed from TI, but looking at figure 15-1 "Display
subsystem highlight" from the TRM, some data pins come near the DSI and SDI
blocks. This is not very hard evidence, but the fact remains that with the
power on, pixels are ok, and with the power off, pixels are not ok.

It may also be that VDDS_SDI is needed to power some pins, but as normally
both VDDS_SDI and VDDS_DSI come from the same power source, this hasn't
been shown.

It seems that a single driver can only get a regulator once. This patch
solves it by getting all the required regulators in one place, and from
which the submodules then get the regulators they need.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Collect interrupt statistics, printable via debugfs:

debugfs/omapdss/dispc_irq
debugfs/omapdss/dsi_irq

The counters are reset when printed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The core files of DSS2. DSS2 commits are split a bit artificially to
make the individual commits smaller, and DSS2 doesn't compile properly
without the rest of the core commits. This shouldn't be a problem, as no
configuration uses DSS2 yet.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>