1. 17 9月, 2013 5 次提交
  2. 16 9月, 2013 3 次提交
    • L
      Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus · d8efd82e
      Linus Torvalds 提交于
      Pull MIPS fixes from Ralf Baechle:
       "These are four patches for three construction sites:
      
         - Fix register decoding for the combination of multi-core processors
           and multi-threading.
      
         - Two more fixes that are part of the ongoing DECstation resurrection
           work.  One of these touches a DECstation-only network driver.
      
         - Finally Markos' trivial build fix for the AP/SP support.
      
        (With this applied now all MIPS defconfigs are building again)"
      
      * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
        MIPS: kernel: vpe: Make vpe_attrs an array of pointers.
        MIPS: Fix SMP core calculations when using MT support.
        MIPS: DECstation I/O ASIC DMA interrupt handling fix
        MIPS: DECstation HRT initialization rearrangement
      d8efd82e
    • L
      Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86 · cd619e21
      Linus Torvalds 提交于
      Pull x86 platform updates from Matthew Garrett:
       "Nothing amazing here, almost entirely cleanups and minor bugfixes and
        one bit of hardware enablement in the amilo-rfkill driver"
      
      * 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
        platform/x86: panasonic-laptop: reuse module_acpi_driver
        samsung-laptop: fix config build error
        platform: x86: remove unnecessary platform_set_drvdata()
        amilo-rfkill: Enable using amilo-rfkill with the FSC Amilo L1310.
        wmi: parse_wdg() should return kernel error codes
        hp_wmi: Fix unregister order in hp_wmi_rfkill_setup()
        platform: replace strict_strto*() with kstrto*()
        x86: irst: use module_acpi_driver to simplify the code
        x86: smartconnect: use module_acpi_driver to simplify the code
        platform samsung-q10: use ACPI instead of direct EC calls
        thinkpad_acpi: add the ability setting TPACPI_LED_NONE by quirk
        thinkpad_acpi: return -NODEV while operating uninitialized LEDs
      cd619e21
    • L
      Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi · 0375ec58
      Linus Torvalds 提交于
      Pull misc SCSI driver updates from James Bottomley:
       "This patch set is a set of driver updates (megaraid_sas, fnic, lpfc,
        ufs, hpsa) we also have a couple of bug fixes (sd out of bounds and
        ibmvfc error handling) and the first round of esas2r checker fixes and
        finally the much anticipated big endian additions for megaraid_sas"
      
      * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
        [SCSI] fnic: fnic Driver Tuneables Exposed through CLI
        [SCSI] fnic: Kernel panic while running sh/nosh with max lun cfg
        [SCSI] fnic: Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset
        [SCSI] fnic: Remove QUEUE_FULL handling code
        [SCSI] fnic: On system with >1.1TB RAM, VIC fails multipath after boot up
        [SCSI] fnic: FC stat param seconds_since_last_reset not getting updated
        [SCSI] sd: Fix potential out-of-bounds access
        [SCSI] lpfc 8.3.42: Update lpfc version to driver version 8.3.42
        [SCSI] lpfc 8.3.42: Fixed issue of task management commands having a fixed timeout
        [SCSI] lpfc 8.3.42: Fixed inconsistent spin lock usage.
        [SCSI] lpfc 8.3.42: Fix driver's abort loop functionality to skip IOs already getting aborted
        [SCSI] lpfc 8.3.42: Fixed failure to allocate SCSI buffer on PPC64 platform for SLI4 devices
        [SCSI] lpfc 8.3.42: Fix WARN_ON when driver unloads
        [SCSI] lpfc 8.3.42: Avoided making pci bar ioremap call during dual-chute WQ/RQ pci bar selection
        [SCSI] lpfc 8.3.42: Fixed driver iocbq structure's iocb_flag field running out of space
        [SCSI] lpfc 8.3.42: Fix crash on driver load due to cpu affinity logic
        [SCSI] lpfc 8.3.42: Fixed logging format of setting driver sysfs attributes hard to interpret
        [SCSI] lpfc 8.3.42: Fixed back to back RSCNs discovery failure.
        [SCSI] lpfc 8.3.42: Fixed race condition between BSG I/O dispatch and timeout handling
        [SCSI] lpfc 8.3.42: Fixed function mode field defined too small for not recognizing dual-chute mode
        ...
      0375ec58
  3. 15 9月, 2013 4 次提交
  4. 14 9月, 2013 8 次提交
  5. 13 9月, 2013 20 次提交
    • L
      Merge branch 'genirq' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux · 399a946e
      Linus Torvalds 提交于
      Pull generic hardirq option removal from Martin Schwidefsky:
       "All architectures now use generic hardirqs, s390 has been last to
        switch.
      
        With that the code under !CONFIG_GENERIC_HARDIRQS and the related
        HAVE_GENERIC_HARDIRQS and GENERIC_HARDIRQS config options can be
        removed.  Yay!"
      
      * 'genirq' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
        Remove GENERIC_HARDIRQ config option
      399a946e
    • L
      Merge branch 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild · 183c4203
      Linus Torvalds 提交于
      Pull kconfig fix from Michal Marek:
       "This is a fix for a regression caused by my previous pull request.
      
        A sed command in scripts/config that used colons as separator was
        accidentally changed to use slashes, which fails when you use slashes
        in a value.  Changing it back to colons is of course not a proper fix,
        but at least it will be broken in the same way it had been for four
        years.  A proper fix is pending"
      
      * 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
        scripts/config: fix variable substitution command
      183c4203
    • L
      Merge tag 'blackfin-for-linus' of... · 951a730a
      Linus Torvalds 提交于
      Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux
      
      Pull blackfin updates from Steven Miao.
      
      * tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
        blackfin: Ignore generated uImages
        blackfin: Add STMMAC platform data to enable dwmac1000 driver on BF60x.
        bf609: adv7343: add S-Video and Component output support
        bf609: add adv7343 video encoder support
        clock: add stmmac clock for ethernet driver
        blackfin: scb: Add SCB1 to SCB9 config options and data.
        blackfin: scb: Add system crossbar init code.
      951a730a
    • L
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 · 0898d2aa
      Linus Torvalds 提交于
      Pull crypto fixes from Herbert Xu:
       "This fixes a 7+ year race condition in the crypto API that causes
        sporadic crashes when multiple threads load the same algorithm.
      
        It also fixes the crct10dif algorithm again to prevent boot failures
        on systems where the initramfs tool ignores module softdeps"
      
      * git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
        crypto: crct10dif - Add fallback for broken initrds
        crypto: api - Fix race condition in larval lookup
      0898d2aa
    • M
      MIPS: kernel: vpe: Make vpe_attrs an array of pointers. · 1b467633
      Markos Chandras 提交于
      Commit 567b21e9
      "mips: convert vpe_class to use dev_groups"
      
      broke the build on MIPS since vpe_attrs should be an array
      of 'struct device_attribute' pointers.
      
      Fixes the following build problem:
      arch/mips/kernel/vpe.c:1372:2: error: missing braces around initializer
      [-Werror=missing-braces]
      arch/mips/kernel/vpe.c:1372:2: error: (near initialization for 'vpe_attrs[0]')
      [-Werror=missing-braces]
      
      Cc: Ralf Baechle <ralf@linux-mips.org>
      Cc: John Crispin <blogic@openwrt.org>
      Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
      Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
      Cc: linux-mips@linux-mips.org
      Patchwork: https://patchwork.linux-mips.org/patch/5819/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      1b467633
    • M
      Remove GENERIC_HARDIRQ config option · 0244ad00
      Martin Schwidefsky 提交于
      After the last architecture switched to generic hard irqs the config
      options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
      for !CONFIG_GENERIC_HARDIRQS can be removed.
      Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
      0244ad00
    • C
      scripts/config: fix variable substitution command · 86eb7818
      Clement Chauplannaz 提交于
      Commit 229455bc02b87f7128f190c4491b4ceffff38648 accidentally changed the
      separator between sed `s' command and its parameters from ':' to '/'.
      
      Revert this change.
      Reported-and-tested-by: NLinus Walleij <linus.walleij@linaro.org>
      Signed-off-by: NClement Chauplannaz <chauplac@gmail.com>
      Signed-off-by: NMichal Marek <mmarek@suse.cz>
      86eb7818
    • L
      MIPS: Fix SMP core calculations when using MT support. · 670bac3a
      Leonid Yegoshin 提交于
      The TCBIND register is only available if the core has MT support. It
      should not be read otherwise. Secondly, the number of TCs (siblings)
      are calculated differently depending on if the kernel is configured
      as SMVP or SMTC.
      Signed-off-by: NLeonid Yegoshin <Leonid.Yegoshin@imgtec.com>
      Signed-off-by: NSteven J. Hill <Steven.Hill@imgtec.com>
      Cc: linux-mips@linux-mips.org
      Patchwork: https://patchwork.linux-mips.org/patch/5822/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      670bac3a
    • M
      MIPS: DECstation I/O ASIC DMA interrupt handling fix · 5359b938
      Maciej W. Rozycki 提交于
      This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
      and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
      the same time, to make I/O ASIC DMA interrupts functional.
      
      Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
      by software by writing 0 to the respective bit in I/O ASIC's System
      Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
      bits are handled in the CPU (the difference is SIR DMA interrupt bits are
      R/W0C so there's no need for an RMW cycle).  Otherwise the handler is
      reentered over and over again.
      
      The only current user is the DEC LANCE Ethernet driver and its extremely
      uncommon DMA memory error handler that does not care when exactly the
      interrupt is cleared.  Anticipating the use of DMA interrupts by the Zilog
      SCC driver this change however exports clear_ioasic_dma_irq for device
      drivers to choose the right application-specific sequence to clear the
      request explicitly rather than calling it implicitly in the .irq_eoi
      handler of `struct irq_chip'.  Previously these interrupts were cleared in
      the .end handler of the said structure, before it was removed.
      Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
      Cc: linux-mips@linux-mips.org
      Patchwork: https://patchwork.linux-mips.org/patch/5826/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      5359b938
    • M
      MIPS: DECstation HRT initialization rearrangement · daed1285
      Maciej W. Rozycki 提交于
      Not all I/O ASIC versions have the free-running counter implemented, an
      early revision used in the 5000/1xx models aka 3MIN and 4MIN did not have
      it.  Therefore we cannot unconditionally use it as a clock source.
      Fortunately if not implemented its register slot has a fixed value so it
      is enough if we check for the value at the end of the calibration period
      being the same as at the beginning.
      
      This also means we need to look for another high-precision clock source on
      the systems affected.  The 5000/1xx can have an R4000SC processor
      installed where the CP0 Count register can be used as a clock source.
      Unfortunately all the R4k DECstations suffer from the missed timer
      interrupt on CP0 Count reads erratum, so we cannot use the CP0 timer as a
      clock source and a clock event both at a time.  However we never need an
      R4k clock event device because all DECstations have a DS1287A RTC chip
      whose periodic interrupt can be used as a clock source.
      
      This gives us the following four configuration possibilities for I/O ASIC
      DECstations:
      
      1. No I/O ASIC counter and no CP0 timer, e.g. R3k 5000/1xx (3MIN).
      
      2. No I/O ASIC counter but the CP0 timer, i.e. R4k 5000/150 (4MIN).
      
      3. The I/O ASIC counter but no CP0 timer, e.g. R3k 5000/240 (3MAX+).
      
      4. The I/O ASIC counter and the CP0 timer, e.g. R4k 5000/260 (4MAX+).
      
      For #1 and #2 this change stops the I/O ASIC free-running counter from
      being installed as a clock source of a 0Hz frequency.  For #2 it also
      arranges for the CP0 timer to be used as a clock source rather than a
      clock event device, because having an accurate wall clock is more
      important than a high-precision interval timer.  For #3 there is no
      change.  For #4 the change makes the I/O ASIC free-running counter
      installed as a clock source so that the CP0 timer can be used as a clock
      event device.
      
      Unfortunately the use of the CP0 timer as a clock event device relies on a
      succesful completion of c0_compare_interrupt.  That never happens, because
      while waiting for a CP0 Compare interrupt to happen the function spins in
      a loop reading the CP0 Count register.  This makes the CP0 Count erratum
      trigger reliably causing the interrupt waited for to be lost in all cases.
      As a result #4 resorts to using the CP0 timer as a clock source as well,
      just as #2.  However we want to keep this separate arrangement in case
      (hope) c0_compare_interrupt is eventually rewritten such that it avoids
      the erratum.
      Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
      Cc: linux-mips@linux-mips.org
      Patchwork: https://patchwork.linux-mips.org/patch/5825/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      daed1285
    • M
      blackfin: Ignore generated uImages · 08b67faa
      Mark Brown 提交于
      We have the build infrastructure to generate uImages so we should ignore
      the resulting generated files.
      Signed-off-by: NMark Brown <broonie@linaro.org>
      Acked-by: NMike Frysinger <vapier@gentoo.org>
      08b67faa
    • S
      blackfin: Add STMMAC platform data to enable dwmac1000 driver on BF60x. · 1d899fd6
      Sonic Zhang 提交于
      - Enable GMAC
      - Set propler DMA PBL
      - Disable DMA store and forward mode
      - Select PTP input clock from MII
      clock.
      Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
      Signed-off-by: NSteven Miao <realmz6@gmail.com>
      1d899fd6
    • S
      e5786092
    • S
      bf609: add adv7343 video encoder support · 4940c53d
      Scott Jiang 提交于
      Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
      4940c53d
    • S
      clock: add stmmac clock for ethernet driver · 3036dccf
      Steven Miao 提交于
      Signed-off-by: NSteven Miao <realmz6@gmail.com>
      3036dccf
    • S
      206f060c
    • S
      blackfin: scb: Add system crossbar init code. · 24a70cf2
      Steven Miao 提交于
      If SCB exists in select blackfin cpu, developer can change the SCB
      priority in kernel configuration.
      Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
      Signed-off-by: NSteven Miao <realmz6@gmail.com>
      24a70cf2
    • L
      Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus · 5a7d8a28
      Linus Torvalds 提交于
      Pull MIPS updates from Ralf Baechle:
       "This has been sitting in -next for a while with no objections and all
        MIPS defconfigs except one are building fine; that one platform got
        broken by another patch in your tree and I'm going to submit a patch
        separately.
      
         - a handful of fixes that didn't make 3.11
         - a few bits of Octeon 3 support with more to come for a later
           release
         - platform enhancements for Octeon, ath79, Lantiq, Netlogic and
           Ralink SOCs
         - a GPIO driver for the Octeon
         - some dusting off of the DECstation code
         - the usual dose of cleanups"
      
      * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (65 commits)
        MIPS: DMA: Fix BUG due to smp_processor_id() in preemptible code
        MIPS: kexec: Fix random crashes while loading crashkernel
        MIPS: kdump: Skip walking indirection page for crashkernels
        MIPS: DECstation HRT calibration bug fixes
        MIPS: Export copy_from_user_page() (needed by lustre)
        MIPS: Add driver for the built-in PCI controller of the RT3883 SoC
        MIPS: DMA: For BMIPS5000 cores flush region just like non-coherent R10000
        MIPS: ralink: Add support for reset-controller API
        MIPS: ralink: mt7620: Add cpu-feature-override header
        MIPS: ralink: mt7620: Add spi clock definition
        MIPS: ralink: mt7620: Add wdt clock definition
        MIPS: ralink: mt7620: Improve clock frequency detection
        MIPS: ralink: mt7620: This SoC has EHCI and OHCI hosts
        MIPS: ralink: mt7620: Add verbose ram info
        MIPS: ralink: Probe clocksources from OF
        MIPS: ralink: Add support for systick timer found on newer ralink SoC
        MIPS: ralink: Add support for periodic timer irq
        MIPS: Netlogic: Built-in DTB for XLP2xx SoC boards
        MIPS: Netlogic: Add support for USB on XLP2xx
        MIPS: Netlogic: XLP2xx update for I2C controller
        ...
      5a7d8a28
    • L
      Merge tag 'xfs-for-linus-v3.12-rc1-2' of git://oss.sgi.com/xfs/xfs · e0ea4045
      Linus Torvalds 提交于
      Pull xfs update #2 from Ben Myers:
       "Here we have defrag support for v5 superblock, a number of bugfixes
        and a cleanup or two.
      
         - defrag support for CRC filesystems
         - fix endian worning in xlog_recover_get_buf_lsn
         - fixes for sparse warnings
         - fix for assert in xfs_dir3_leaf_hdr_from_disk
         - fix for log recovery of remote symlinks
         - fix for log recovery of btree root splits
         - fixes formemory allocation failures with ACLs
         - fix for assert in xfs_buf_item_relse
         - fix for assert in xfs_inode_buf_verify
         - fix an assignment in an assert that should be a test in
           xfs_bmbt_change_owner
         - remove dead code in xlog_recover_inode_pass2"
      
      * tag 'xfs-for-linus-v3.12-rc1-2' of git://oss.sgi.com/xfs/xfs:
        xfs: remove dead code from xlog_recover_inode_pass2
        xfs: = vs == typo in ASSERT()
        xfs: don't assert fail on bad inode numbers
        xfs: aborted buf items can be in the AIL.
        xfs: factor all the kmalloc-or-vmalloc fallback allocations
        xfs: fix memory allocation failures with ACLs
        xfs: ensure we copy buffer type in da btree root splits
        xfs: set remote symlink buffer type for recovery
        xfs: recovery of swap extents operations for CRC filesystems
        xfs: swap extents operations for CRC filesystems
        xfs: check magic numbers in dir3 leaf verifier first
        xfs: fix some minor sparse warnings
        xfs: fix endian warning in xlog_recover_get_buf_lsn()
      e0ea4045
    • L
      Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending · 48efe453
      Linus Torvalds 提交于
      Pull SCSI target updates from Nicholas Bellinger:
       "Lots of activity again this round for I/O performance optimizations
        (per-cpu IDA pre-allocation for vhost + iscsi/target), and the
        addition of new fabric independent features to target-core
        (COMPARE_AND_WRITE + EXTENDED_COPY).
      
        The main highlights include:
      
         - Support for iscsi-target login multiplexing across individual
           network portals
         - Generic Per-cpu IDA logic (kent + akpm + clameter)
         - Conversion of vhost to use per-cpu IDA pre-allocation for
           descriptors, SGLs and userspace page pointer list
         - Conversion of iscsi-target + iser-target to use per-cpu IDA
           pre-allocation for descriptors
         - Add support for generic COMPARE_AND_WRITE (AtomicTestandSet)
           emulation for virtual backend drivers
         - Add support for generic EXTENDED_COPY (CopyOffload) emulation for
           virtual backend drivers.
         - Add support for fast memory registration mode to iser-target (Vu)
      
        The patches to add COMPARE_AND_WRITE and EXTENDED_COPY support are of
        particular significance, which make us the first and only open source
        target to support the full set of VAAI primitives.
      
        Currently Linux clients are lacking upstream support to actually
        utilize these primitives.  However, with server side support now in
        place for folks like MKP + ZAB working on the client, this logic once
        reserved for the highest end of storage arrays, can now be run in VMs
        on their laptops"
      
      * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (50 commits)
        target/iscsi: Bump versions to v4.1.0
        target: Update copyright ownership/year information to 2013
        iscsi-target: Bump default TCP listen backlog to 256
        target: Fix >= v3.9+ regression in PR APTPL + ALUA metadata write-out
        iscsi-target; Bump default CmdSN Depth to 64
        iscsi-target: Remove unnecessary wait_for_completion in iscsi_get_thread_set
        iscsi-target: Add thread_set->ts_activate_sem + use common deallocate
        iscsi-target: Fix race with thread_pre_handler flush_signals + ISCSI_THREAD_SET_DIE
        target: remove unused including <linux/version.h>
        iser-target: introduce fast memory registration mode (FRWR)
        iser-target: generalize rdma memory registration and cleanup
        iser-target: move rdma wr processing to a shared function
        target: Enable global EXTENDED_COPY setup/release
        target: Add Third Party Copy (3PC) bit in INQUIRY response
        target: Enable EXTENDED_COPY setup in spc_parse_cdb
        target: Add support for EXTENDED_COPY copy offload emulation
        target: Avoid non-existent tg_pt_gp_mem in target_alua_state_check
        target: Add global device list for EXTENDED_COPY
        target: Make helpers non static for EXTENDED_COPY command setup
        target: Make spc_parse_naa_6h_vendor_specific non static
        ...
      48efe453