Signed-off-by: NRayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows to set the mtu bigger than 1500
in case of normal descriptors.
This is helping some SPEAr customers.
Signed-off-by: NDeepak SIKRI <deepak.sikri@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a problem raised on Orly ARM SMP platform
where, in case of fragmented frames, the descriptors
in the TX ring resulted broken. This was due to a missing lock
protection in the tx process.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch stops advertising 1000Base capablities if GMAC is either
configured for MII or RMII mode and on board there is a GPHY plugged on.
Without this patch if an GBit switch is connected on MII interface,
Ethernet stops working at all.

Discovered as part of
https://bugzilla.stlinux.com/show_bug.cgi?id=14148 triage
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sysfs is a core piece of ifrastructure that many people use and
few people have all of the rules in their head on how to use
it correctly.  Add warnings for people using tagged directories
improperly to that any misuses can be caught and diagnosed quickly.

A single inexpensive test in sysfs_find_dirent is almost sufficient
to catch all possible misuses.  An additional warning is needed
in sysfs_add_dirent so that we actually fail when attempting to
add an untagged dirent in a tagged directory.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that /sys/class/net/bonding_masters is implemented as a tagged sysfs
file we can remove support for untagged files in tagged directories.

This change removes any ambiguity of what a NULL namespace value
means.  A NULL namespace parameter after this patch means
that we are talking about an untagged sysfs dirent.

This makes the sysfs code much less prone to mistakes when during
maintenance.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a network namespace misfeature that bonding_masters looked at
current instead of the remembering the context where in which
/sys/class/net/bonding_masters was opened in to see which network
namespace to act upon.

This removes the need for sysfs to handle tagged directories with
untagged members allowing for a conceptually simpler sysfs
implementation.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Looking up files in sysfs is hard to understand and analyize because we
currently allow placing untagged files in tagged directories.  In the
implementation of that we have two subtly different meanings of NULL.
NULL meaning there is no tag on a directory entry and NULL meaning
we don't care which namespace the lookup is performed for.  This
multiple uses of NULL have resulted in subtle bugs (since fixed)
in the code.

Currently it is only the bonding driver that needs to have an untagged
file in a tagged directory.

To untagle this mess I am adding support for tagged files to sysfs.
Modifying the bonding driver to implement bonding_masters as a tagged
file.  Registering bonding_masters once for each network namespace.
Then I am removing support for untagged entries in tagged sysfs
directories.

Resulting in code that is much easier to reason about.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The port shouldn't be enabled unless its current MUX
state is DISTRIBUTING which is correctly handled by
ad_mux_machine(), otherwise the packet sent can be
lost because the other end may not be ready.

The issue happens on every port initialization, but
as the ports are expected to move quickly to DISTRIBUTING,
it doesn't cause much problem.  However, it does cause
constant packet loss if the other peer has the port
configured to stay in STANDBY (i.e. SYNC set to OFF).
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a sanity check on the values provided by user space for
the hardware time stamping configuration. If the values lie outside of
the absolute limits, then the ioctl request will be denied.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the rcu_barrier from rollback_registered_many
(inside the rtnl_lock) into netdev_run_todo (just outside the rtnl_lock).
This allows us to gain the full benefit of sychronize_net calling
synchronize_rcu_expedited when the rtnl_lock is held.

The rcu_barrier in rollback_registered_many was originally a synchronize_net
but was promoted to be a rcu_barrier() when it was found that people were
unnecessarily hitting the 250ms wait in netdev_wait_allrefs().  Changing
the rcu_barrier back to a synchronize_net is therefore safe.

Since we only care about waiting for the rcu callbacks before we get
to netdev_wait_allrefs() it is also safe to move the wait into
netdev_run_todo.

This was tested by creating and destroying 1000 tap devices and observing
/proc/lock_stat.  /proc/lock_stat reports this change reduces the hold
times of the rtnl_lock by a factor of 10.  There was no observable
difference in the amount of time it takes to destroy a network device.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initial cwnd being 10 (TCP_INIT_CWND) instead of 3, change
tcp_fixup_sndbuf() to get more than 16384 bytes (sysctl_tcp_wmem[1]) in
initial sk_sndbuf
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Vitesse driver was using the RGMII_ID interface type to determine if
skew was necessary.  However, we want to move away from using that
interface type, as it's really a property of the board's PHY connection.
However, some boards depend on it, so we want to support it, while
allowing new boards to use the more flexible "fixups" approach.  To do
this, we extract the code which adds skew into its own function, and
call that function when RGMII_ID has been selected.

Another side-effect of this change is that if your PHY has skew set
already, it doesn't clear it.  This way, the fixup code can modify the
register without config_init then clearing it.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_recycle_check resets the skb if it's eligible for recycling.
However, there are times when a driver might want to optionally
manipulate the skb data with the skb before resetting the skb,
but after it has determined eligibility.  We do this by splitting the
eligibility check from the skb reset, creating two inline functions to
accomplish that task.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Acked-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver version updated to 1.5.4.2
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moving to Toeplitz function in RSS calculation.
Reporting rxhash in skb.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not updating common counters from data path.
The checksum counters are per ring, summarizing them when collecting statistics.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Canceling FCS removal where FW allows for better alignment
of incoming data.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent overflow when trying to register more Vlans then the Vlan table in
HW is configured to.
Need to take into acount that the first 2 entries are reserved.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added recovery check of CA wake status in case of wake up timeout.
Added check of CA wake status in case of wake down timeout.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added sanity check for length of CAIF frames, and tear down of
CAIF link-layer device upon protocol error.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CAIF HSI uses a timer for inactivity. Upon timeout HSI-wake signaling
is initiated to allow power-down of the HSI block.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Platform device is no longer removed from caif_hsi at shutdown.
The HSI-platform device must do it's own registration and unregistration.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some platforms do not allow to put HSI block into low-power
mode when FIFO is not empty. The patch flushes (by reading)
FIFO at wake down sequence. Asynchronous read and write is
implemented for that. As a side effect this will also greatly
improve performance.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under stressed conditions a race could happen when del_timer_sync() was called
from softirq context at the same time when mod_timer_pending() for the same
timer was called from the workqueue. This leaded to a state mismatch in the
CAIF HSI driver and following unexpected link wakeup procedure.

The fix puts del_timer_sync() and mod_timer_pending() calls under a spin lock
to protect against the race condition.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cfhsi->tx_state was not protected by a spin lock. TX soft-irq could interrupt
cfhsi_tx_done_work work leading to inconsistent state of the driver.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CAIF HSI header may be uninitialized and cause last message to
be repeated if transmit size is ~86 bytes long.
Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.

Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling icmpv6_send() on a local message size error leads to
an incorrect update of the path mtu. So use xfrm6_local_rxpmtu()
to notify about the pmtu if the IPV6_DONTFRAG socket option is
set on an udp or raw socket, according RFC 3542 and use
ipv6_local_error() otherwise.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip6_append_data() builds packets based on the mtu from dst_mtu(rt->dst.path).
On IPsec the effective mtu is lower because we need to add the protocol
headers and trailers later when we do the IPsec transformations. So after
the IPsec transformations the packet might be too big, which leads to a
slowpath fragmentation then. This patch fixes this by building the packets
based on the lower IPsec mtu from dst_mtu(&rt->dst) and adapts the exthdr
handling to this.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pointer to mtu_info is taken from the common buffer
of the skb, thus it can't be a NULL pointer. This patch
removes this check on mtu_info.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The replay check and replay advance functions had some code
duplications. This patch removes the duplications.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The extra delay of 2ns to adjust RX clock phase is actually needed
in RGMII mode. Tested on the HDK7108 (STx7108c2).
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following configuration used to work as I expected. At least
we could use the fcoe interfaces to do MPIO and the bond0 iface
to do load balancing or failover.

       ---eth2.228-fcoe
       |
eth2 -----|
          |
          |---- bond0
          |
eth3 -----|
       |
       ---eth3.228-fcoe

This worked because of a change we added to allow inactive slaves
to rx 'exact' matches. This functionality was kept intact with the
rx_handler mechanism. However now the vlan interface attached to the
active slave never receives traffic because the bonding rx_handler
updates the skb->dev and goto's another_round. Previously, the
vlan_do_receive() logic was called before the bonding rx_handler.

Now by the time vlan_do_receive calls vlan_find_dev() the
skb->dev is set to bond0 and it is clear no vlan is attached
to this iface. The vlan lookup fails.

This patch moves the VLAN check above the rx_handler. A VLAN
tagged frame is now routed to the eth2.228-fcoe iface in the
above schematic. Untagged frames continue to the bond0 as
normal. This case also remains intact,

eth2 --> bond0 --> vlan.228

Here the skb is VLAN tagged but the vlan lookup fails on eth2
causing the bonding rx_handler to be called. On the second
pass the vlan lookup is on the bond0 iface and completes as
expected.

Putting a VLAN.228 on both the bond0 and eth2 device will
result in eth2.228 receiving the skb. I don't think this is
completely unexpected and was the result prior to the rx_handler
result.

Note, the same setup is also used for other storage traffic that
MPIO is used with eg. iSCSI and similar setups can be contrived
without storage protocols.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NJesse Gross <jesse@nicira.com>
Reviewed-by: NJiri Pirko <jpirko@redhat.com>
Tested-by: NHans Schillstrom <hams.schillstrom@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cs89x0 driver was initial placed in the apple/ when it
should have been placed in the cirrus/.  This resolves the
issue by moving the dirver and fixing up the respective
Kconfig(s) and Makefile(s).

Thanks to Sascha for reporting the issue.

-v2 Fix a config error that was introduced with v1 by removing
    the dependency on MACE for NET_VENDOR_APPLE.

CC: Russell Nelson <nelson@crynwr.com>
CC: Andrew Morton <akpm@linux-foundation.org>
Reported-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pppol2tp_xmit() calls skb_cow_head(skb, 2) before calling
l2tp_xmit_skb()

Then l2tp_xmit_skb() calls again skb_cow_head(skb, large_headroom)

This patchs changes the first skb_cow_head() call to supply the needed
headroom to make sure at most one (expensive) pskb_expand_head() is
done.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fragmented multicast frames are delivered to a single macvlan port,
because ip defrag logic considers other samples are redundant.

Implement a defrag step before trying to send the multicast frame.
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>