Initialise PXA devices before platform initialisation, so that
platforms can parent devices to these.
Acked-by: Neric miao <ymiao3@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Changes include:

1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate
   the board capability of this pin to wakeup the system

2. add gpio_set_wake() and keypad_set_wake() to allow dynamically
   enable/disable wakeup from GPIOs and keypad GPIO

   * these functions are currently kept in mfp-pxa2xx.c due to their
     dependency to the MFP configuration

3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP
   is set on incorrect pins

So that the GPIO's wakeup capability is now decided by the following:

   a) processor's capability: (only those GPIOs which have dedicated
      bits within PWER/PRER/PFER can wakeup the system), this is
      initialized by pxa{25x,27x}_init_mfp()

   b) board design decides:
      - whether the pin is designed to wakeup the system (some of
        the GPIOs are configured as other functions, which is not
        intended to be a wakeup source), by OR'ing the pin config
        with MFP_LPM_CAN_WAKEUP

      - which edge the pin is designed to wakeup the system, this
        may depends on external peripherals/connections, which is
        totally board specific; this is indicated by MFP_LPM_EDGE_*

   c) the corresponding device's (most likely the gpio_keys.c) wakeup
      attribute:
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

To further clean up the GPIO and IRQ structure:

1. pxa_init_irq_gpio() and pxa_init_gpio() combines into a single
   function pxa_init_gpio()

2. assignment of set_wake merged into pxa_init_{irq,gpio}() as
   an argument
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This makes the code better organized and simplified a bit.  The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.

This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable.  The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)

The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).

"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This adds back the registration of HWUART clock on pxa25x
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The PXA manuals indicate that when in standby or sleep modes, clocks to
peripherals are shut off by the processor itself.  Eg:

PXA270 standby: "In standby mode, all clocks are disabled except those
 for the power manager and the RTC."

PXA270 sleep: "In sleep mode, all clocks are disabled to the processor
 and to all peripherals except the RTC."

PXA255 sleep: "In Sleep Mode, all processor and peripheral clocks are
 disabled, except the RTC."

Therefore, it should be safe to leave the clock enable register alone
prior to entering low power modes for these SoCs.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Only register the MMC, framebuffer, I2C and FICP devices when the
platform supplies the necessary platform data structures for the
devices.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Suspend/resume on the pxa25x was fairly obviously broken in revision
711be5cc.

This patch fixes the damage by adding back the missing code.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The name of 'struct pm_ops' suggests that it is related to the power
management in general, but in fact it is only related to suspend.   Moreover,
its name should indicate what this structure is used for, so it seems
reasonable to change it to 'struct platform_suspend_ops'.   In that case, the
name of the global variable of this type used by the PM core and the names of
related functions should be changed accordingly.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move the definition of 'struct pm_ops' and related functions from <linux/pm.h>
to <linux/suspend.h> .

There are, at least, the following reasons to do that:
* 'struct pm_ops' is specifically related to suspend and not to the power
  management in general.
* As long as 'struct pm_ops' is defined in <linux/pm.h>, any modification of it
  causes the entire kernel to be recompiled, which is unnecessary and annoying.
* Some suspend-related features are already defined in <linux/suspend.h>, so it
  is logical to move the definition of 'struct pm_ops' into there.
* 'struct hibernation_ops', being the hibernation-related counterpart of
  'struct pm_ops', is defined in <linux/suspend.h> .
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

a function pxa_init_irq_set_wake() was introduced, so that
processor specific code could install their own version

code setting PFER and PRER registers within pxa_gpio_irq_type
are removed, and the edge configuration is postponed to the
(*set_wake) and copies the GRER and GFER register, which will
always be set up correctly by pxa_gpio_irq_type()
Signed-off-by: Neric miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rename pxa25x and pxa27x memory/lcd/core clock functions, and
select the correct version at run time.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. split pxa_cpu_suspend to pxa25x_cpu_suspend and pxa27x_cpu_suspend
   and make pxa25x_cpu_pm_enter() and pxa27x_cpu_pm_enter() to invoke
   the corresponding _suspend functions, thus remove all those ugly
   #ifdef .. #endif out of sleep.S

2. move the declarations of those suspend functions to pm.h

note: this is not a clean enough solution until all the pxa25x and
pxa27x specific part is further removed out of sleep.S, sleep.S is
supposed to contain generic code only
Signed-off-by: Neric miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. introduce a structure pxa_cpu_pm_fns for pxa25x/pxa27x specific
   operations as follows:

	struct pxa_cpu_pm_fns {
		int	save_size;
		void	(*save)(unsigned long *);
		void	(*restore)(unsigned long *);
		int	(*valid)(suspend_state_t state);
		void	(*enter)(suspend_state_t state);
	}

2. processor specific registers saving and restoring are performed
   by calling the corresponding (*save) and (*restore)

3. pxa_cpu_pm_fns->save_size should be initialized to the required
   size for processor specific registers saving, the allocated
   memory address will be passed to (*save) and (*restore)

   memory allocation happens early in pxa_pm_init(), and save_size
   should be assigned prior to this (which is usually true, since
   pxa_pm_init() happens in device_initcall()

4. there're some redundancies for those SLEEP_SAVE_XXX and related
   macros, will be fixed later, one way possible is for the system
   devices to handle the specific registers saving and restoring
Signed-off-by: Neric miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. for common devices across all the pxa variants, the names
   are changed to be:
     "pxa_device_xxx"

2. for pxa25x or pxa27x specific devices, the names are
   changed to be:
     "pxa25x_device_xxx", or
     "pxa27x_device_xxx"
Signed-off-by: Neric miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This allows individual CPU support to determine which platform
devices should be registered.  Also fix a copy-n-paste bug in
the I2C power platform device entry.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since the number of dma channels varies between pxa25x and pxa27x, it
introduces some specific code in dma.c. This patch moves the specific
code to pxa25x.c and pxa27x.c and makes dma.c more generic.

1. add pxa_init_dma() for dma initialization, the number of channels
   are passed in by the argument

2. add a "prio" field to the "struct pxa_dma_channel" for the channel
   priority, and is initialized in pxa_init_dma()

3. use a general priority comparison with the channels "prio" field so
   to remove the processor specific pxa_for_each_dma_prio macro,  this
   is not lightning fast as the original one,  but it is acceptable as
   it happens when requesting dma, which is usually not so performance
   critical
Signed-off-by: Neric miao <eric.miao@marvell.com>
Acked-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

/* should be ok this time, I aligned this patch to your arm:pxa2.mbox */

1. move pxa25x specific IRQ initialization code to pxa25x_init_irq()
and pxa27x code to pxa27x_init_irq(), remove pxa_init_irq()

2. replace all pxa_init_irq() with their PXA25x or PXA27x specific
functions
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

pxa_pm_prepare() tried to validate the suspend method type.  As
noted in previous commits:
	eb9289eb
	9c372d06
	e8c9c502

the checking of the suspend type in the 'prepare' method is the
wrong place to do this; use the 'valid' method instead.  This
means that pxa_pm_prepare() can be entirely removed.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the pm_ops structure into the PXA25x and PXA27x support
files.  Remove the old pxa_pm_prepare() function, and rename
the both pxa_cpu_pm_prepare() functions as pxa_pm_prepare().
We'll fix that later.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Patch from Todd Poynor

Add symbols for PXA2xx PWRMODE register M field that selects low-power
mode, replace unadorned constants.  Honor power mode parameter of
pxa_cpu_suspend(mode), no longer force to 3 (sleep).  Full Deep Sleep
low-power mode support for PXA27x is pending generic PM interfaces to
select more than 2 suspend-to-RAM-style power modes, but this is
expected soon. This can be hardcoded in the meantime by replacing the
pxa_cpu_suspend() parameter value.  From David Burrage and Todd Poynor.
Try #2 removes one of the register copies and moves the code to save the
pxa_cpu_suspend parameter to immediately surround the call that requires
the parameter value be preserved.
Signed-off-by: NTodd Poynor <tpoynor@mvista.com>
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

Signed-off-by: Nicolas Pitre
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Todd Poynor

PXA27x sleep fixes:
* set additional sleep/wakeup registers for Mainstone boards.
* move CKEN=0 to pxa25x-specific code; that value is harmful on pxa27x.
* save/restore additional registers, including some found necessary for
C5 processors and/or newer blob versions.
* enable future support of additional sleep modes for PXA27x (eg,
standby, deep sleep).
* split off cpu-specific sleep processing between pxa27x and pxa25x into
separate files (partly in preparation for additional sleep modes).
Includes fixes from David Burrage.

Signed-off-by: Todd Poynor
Signed-off-by: Nicolas Pitre
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!