There's no need to setup the frame pointer again in
call_handle_tlbmiss. The frame pointer will already have been setup in
handle_interrupt.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Unfortunately, due to poor DWARF info in current toolchains, unwinding
through interrutps cannot be done reliably. The problem is that the
DWARF info for function epilogues is wrong.

Take this standard epilogue sequence,

80003cc4:       e3 6f           mov     r14,r15
80003cc6:       26 4f           lds.l   @r15+,pr
80003cc8:       f6 6e           mov.l   @r15+,r14
						<---- interrupt here
80003cca:       f6 6b           mov.l   @r15+,r11
80003ccc:       f6 6a           mov.l   @r15+,r10
80003cce:       f6 69           mov.l   @r15+,r9
80003cd0:       0b 00           rts

If we take an interrupt at the highlighted point, the DWARF info will
bogusly claim that the return address can be found at some offset from
the frame pointer, even though the frame pointer was just restored. The
worst part is if the unwinder finds a text address at the bogus stack
address - unwinding will continue, for a bit, until it finally comes
across an unexpected address on the stack and blows up.

The only solution is to stop unwinding once we've calculated the
function that was executing when the interrupt occurred. This PC can be
easily calculated from pt_regs->pc.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

In order to allow the DWARF unwinder to unwind through exceptions we
need to setup the frame pointer register (r14).
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The address that ret_from_exception and ret_from_irq will return to is
found in the stack slot for SPC, not PR. This error was causing the
DWARF unwinder to pick up the wrong return address on the stack and then
unwind using the unwind tables for the wrong function.

While I'm here I might as well add CFI annotations for the other
registers since they could be useful when unwinding.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The current root hub polling code exhibits a spinlock recursion on the
private controller lock. r8a66597_root_hub_control() is called from
r8a66597_timer() which grabs the lock and disables IRQs. The following
chain emerges:

  r8a66597_timer() <-- lock taken
    r8a66597_root_hub_control()
      r8a66597_check_syssts()
        usb_hcd_poll_rh_status() <-- acquires the same lock
	/* insert death here */

The entire chain requires IRQs to be disabled, so we just unlock and
relock around the call to usb_hcd_poll_rh_status() while leaving the
IRQ state unchanged.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>

This implements the same D-cache flushing logic for r8a66597-hcd as
Catalin's isp1760 (http://patchwork.kernel.org/patch/76391/) change,
with the same note applying here as well:

    When the HDC driver writes the data to the transfer buffers it
    pollutes the D-cache (unlike DMA drivers where the device writes
    the data). If the corresponding pages get mapped into user space,
    there are no additional cache flushing operations performed and
    this causes random user space faults on architectures with
    separate I and D caches (Harvard) or those with aliasing D-cache.

This fixes up crashes during USB boot on SH7724 and others:

	http://marc.info/?l=linux-sh&m=126439837308912&w=2Reported-by: NGoda Yusuke <goda.yusuke@renesas.com>
Tested-by: NGoda Yusuke <goda.yusuke@renesas.com>
Cc: stable@kernel.org
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Acked-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: Fix wrong register in proc-arm6_7.S data abort handler
  ARM: 5909/1: ARM: Correct the FPSCR bits setting when raising exceptions
  ARM: 5904/1: ARM: Always generate the IT instruction when compiling for Thumb-2
  ARM: 5907/1: ARM: Fix the reset on the RealView PBX Development board
  mx35: add a missing comma in a pad definition
  mx25: make the FEC AHB clk secondary of the IPG
  mx25: fix time accounting
  mx25: properly initialize clocks
  mx25: remove unused mx25_clocks_init() argument
  i.MX25: implement secondary clocks for uarts and fec
  i.MX25: Allow secondary clocks in DEFINE_CLOCK
  ARM: MX3: Fixed typo in declared enum type name.
  MXC: Add AUDMUXv2 register decode to debugfs
  mx31ads: Provide an IRQ range to the WM835x on the 1133-EV1 module
  mx31ads: Provide a name for EXPIO interrupt chip
  mx31ads: Allow enable/disable of switchable supplies

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  omap: Disable serial port autoidle by default
  omap: Fix access to already released memory in clk_debugfs_register_one()
  omap: Fix arch/arm/mach-omap2/mux.c: Off by one error
  omap: Fix 3630 mux errors
  OMAP2/3: GPMC: ensure valid clock pointer
  OMAP2/3: IRQ: ensure valid base address
  ARCH OMAP : enable ARCH_HAS_HOLES_MEMORYMODEL for OMAP
  omap: Remove old unused defines for OMAP_32KSYNCT_BASE
  omap: define _toggle_gpio_edge_triggering only for OMAP1

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: Don't clobber the attribute type in nfs_update_inode()
  NFS: Fix a umount race
  NFS: Fix an Oops when truncating a file
  NFS: Ensure that we handle NFS4ERR_STALE_STATEID correctly
  NFSv4.1: Don't call nfs4_schedule_state_recovery() unnecessarily
  NFSv4: Don't allow posix locking against servers that don't support it
  NFSv4: Ensure that the NFSv4 locking can recover from stateid errors
  NFS: Avoid warnings when CONFIG_NFS_V4=n
  NFS: Make nfs_commitdata_release static
  NFS: Try to commit unstable writes in nfs_release_page()
  NFS: Fix a reference leak in nfs_wb_cancel_page()

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  futex: Handle futex value corruption gracefully
  futex: Handle user space corruption gracefully
  futex_lock_pi() key refcnt fix
  softlockup: Add sched_clock_tick() to avoid kernel warning on kgdb resume

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
  GFS2: Extend umount wait coverage to full glock lifetime
  GFS2: Wait for unlock completion on umount

Commit 859ddf09 tried to fix
misallocation bug but broke full bit marking by not clearing
pa[idp->layers] and also is causing X failures due to lookup failure
in drm code.  The cause of the latter hasn't been found yet.  Revert
the fix for now.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: fix interrupt state restore
  microblaze: Defconfig update

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  saa7146: stop DMA before de-allocating DMA scatter/gather page buffers
  V4L/DVB: saa7134: remove stray unlock_kernel

Currently the omap serial clocks are autoidled after 5 seconds.
However, this causes lost characters on the serial ports. As this
is considered non-standard behaviour for Linux, disable the timeout.

Note that this will also cause blocking of any deeper omap sleep
states.

To enable the autoidling of the serial ports, do something like
this for each serial port:

# echo 5 > /sys/devices/platform/serial8250.0/sleep_timeout
# echo 5 > /sys/devices/platform/serial8250.1/sleep_timeout
...
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

I have found an access to already released memory in
clk_debugfs_register_one() function.
Signed-off-by: NMarek Skuczynski <mareksk7@gmail.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

David Binderman ran the sourceforge tool cppcheck over the source code of the
new Linux kernel 2.6.33-rc6:

[./arm/mach-omap2/mux.c:492]: (error) Buffer access out-of-bounds

13 characters + 1 digit + 1 zero byte is more than 14 characters.

Also add a comment on mode0 name length in case new omaps
start using longer names.
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

3630 has more mux signals than 34xx. The additional pins
exist in omap36xx_cbp_subset, but are not initialized
as the superset is missing these offsets. This causes
the following errors during the boot:

mux: Unknown entry offset 0x236
mux: Unknown entry offset 0x22e
mux: Unknown entry offset 0x1ec
mux: Unknown entry offset 0x1ee
mux: Unknown entry offset 0x1f4
mux: Unknown entry offset 0x1f6
mux: Unknown entry offset 0x1f8
mux: Unknown entry offset 0x1fa
mux: Unknown entry offset 0x1fc
mux: Unknown entry offset 0x22a
mux: Unknown entry offset 0x226
mux: Unknown entry offset 0x230
mux: Unknown entry offset 0x22c
mux: Unknown entry offset 0x228

Fix this by adding the missing offsets to omap3 superset.
Note that additionally the uninitialized pins need to be
skipped on 34xx.

Based on an earlier patch by Allen Pais <allen.pais@ti.com>.
Reported-by: NAllen Pais <allen.pais@ti.com>
Signed-off-by: NAllen Pais <allen.pais@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Ensure valid clock pointer during GPMC init.  Fixes compiler
warning about potential use of uninitialized variable.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Ensure valid base address during IRQ init.  Fixes compiler warning
about potential use of uninitialized variable.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP platforms(like OMAP3530) include DSP or other co-processors
for media acceleration. when carving out memory for the
accelerators we can end up creating a hole in the memory map
of sort:
<kernel memory><hole(memory for accelerator)><kernel memory>

To handle such a memory configuration ARCH_HAS_HOLES_MEMORYMODEL
has to be enabled. For further information refer discussion at:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15262.html.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove old unused defines for OMAP_32KSYNCT_BASE
Signed-off-by: NTony Lindgren <tony@atomide.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: fix potential leak of dirty data on umount

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The WARN_ON in lookup_pi_state which complains about a mismatch
between pi_state->owner->pid and the pid which we retrieved from the
user space futex is completely bogus.

The code just emits the warning and then continues despite the fact
that it detected an inconsistent state of the futex. A conveniant way
for user space to spam the syslog.

Replace the WARN_ON by a consistency check. If the values do not match
return -EINVAL and let user space deal with the mess it created.

This also fixes the missing task_pid_vnr() when we compare the
pi_state->owner pid with the futex value.
Reported-by: NJermome Marchand <jmarchan@redhat.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NDarren Hart <dvhltc@us.ibm.com>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <stable@kernel.org>

If the owner of a PI futex dies we fix up the pi_state and set
pi_state->owner to NULL. When a malicious or just sloppy programmed
user space application sets the futex value to 0 e.g. by calling
pthread_mutex_init(), then the futex can be acquired again. A new
waiter manages to enqueue itself on the pi_state w/o damage, but on
unlock the kernel dereferences pi_state->owner and oopses.

Prevent this by checking pi_state->owner in the unlock path. If
pi_state->owner is not current we know that user space manipulated the
futex value. Ignore the mess and return -EINVAL.

This catches the above case and also the case where a task hijacks the
futex by setting the tid value and then tries to unlock it.
Reported-by: NJermome Marchand <jmarchan@redhat.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NDarren Hart <dvhltc@us.ibm.com>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <stable@kernel.org>

This fixes a futex key reference count bug in futex_lock_pi(),
where a key's reference count is incremented twice but decremented
only once, causing the backing object to not be released.

If the futex is created in a temporary file in an ext3 file system,
this bug causes the file's inode to become an "undead" orphan,
which causes an oops from a BUG_ON() in ext3_put_super() when the
file system is unmounted. glibc's test suite is known to trigger this,
see <http://bugzilla.kernel.org/show_bug.cgi?id=14256>.

The bug is a regression from 2.6.28-git3, namely Peter Zijlstra's
38d47c1b "[PATCH] futex: rely on
get_user_pages() for shared futexes". That commit made get_futex_key()
also increment the reference count of the futex key, and updated its
callers to decrement the key's reference count before returning.
Unfortunately the normal exit path in futex_lock_pi() wasn't corrected:
the reference count is incremented by get_futex_key() and queue_lock(),
but the normal exit path only decrements once, via unqueue_me_pi().
The fix is to put_futex_key() after unqueue_me_pi(), since 2.6.31
this is easily done by 'goto out_put_key' rather than 'goto out'.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NDarren Hart <dvhltc@us.ibm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>

If the NFS_ATTR_FATTR_TYPE field isn't set in fattr->valid, then we should
not set the S_IFMT part of inode->i_mode.
Reported-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Ensure that we unregister the bdi before kill_anon_super() calls
ida_remove() on our device name.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org

The VM/VFS does not allow mapping->a_ops->invalidatepage() to fail.
Unfortunately, nfs_wb_page_cancel() may fail if a fatal signal occurs.
Since the NFS code assumes that the page stays mapped for as long as the
writeback is active, we can end up Oopsing (among other things).

The only safe fix here is to convert nfs_wait_on_request(), so as to make
it uninterruptible (as is already the case with wait_on_page_writeback()).
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org

Interrupts must be disabled while an interrupt state restore
(prep for interrupt return) is in progress.
Code to do this was lost in the port to the mainline kernel.
Signed-off-by: NSteven J. Magnani <steve@digidescorp.com>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Although all glocks are, by the time of the umount glock wait,
scheduled for demotion, some of them haven't made it far
enough through the process for the original set of waiting
code to wait for them.

This extends the ref count to the whole glock lifetime in order
to ensure that the waiting does catch all glocks. It does make
it a bit more invasive, but it seems the only sensible solution
at the moment.
Signed-off-by: NSteven Whitehouse <swhiteho@redhat.com>

This patch adds a wait on umount between the point at which we
dispose of all glocks and the point at which we unmount the
lock protocol. This ensures that we've received all the replies
to our unlock requests before we stop the locking.
Signed-off-by: NSteven Whitehouse <swhiteho@redhat.com>
Reported-by: NFabio M. Di Nitto <fdinitto@redhat.com>

There were several changes in Microblaze defconfig that's why
is good to update defconfigs.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  kernel/cred.c: use kmem_cache_free

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
  connector: Delete buggy notification code.
  be2net: use eq-id to calculate cev-isr reg offset
  Bluetooth: Use the control channel for raw HID reports
  Bluetooth: Add DFU driver for Atheros Bluetooth chipset AR3011
  Bluetooth: Redo checks in IRQ handler for shared IRQ support
  Bluetooth: Fix memory leak in L2CAP
  Bluetooth: Remove double free of SKB pointer in L2CAP
  cdc_ether: Partially revert "usbnet: Set link down initially ..."
  be2net: Fix memset() arg ordering.
  bonding: bond_open error return value
  ixgbe: if ixgbe_copy_dcb_cfg is going to fail learn about it early
  ixgbe: set the correct DCB bit for pg tx settings
  igbvf: fix issue w/ mapped_as_page being left set after unmap
  drivers/net: ks8851_mll ethernet network driver
  be2net: Bug fix to support newer generation of BE ASIC
  starfire: clean up properly if firmware loading fails
  mac80211: fix NULL pointer dereference when ftrace is enabled
  netfilter: ctnetlink: fix expectation mask dump
  ipv6: conntrack: Add member of user to nf_ct_frag6_queue structure
  ath9k: fix eeprom INI values override for 2GHz-only cards
  ...

This is the counterpart to cba76717
("pktcdvd: remove broken dev_t export of class devices").  Device is not
registered using dev_t, so it should not be destroyed using device_destroy
which looks up the device by dev_t.  This will fail and adding the device
again will fail with the "duplicate name" error.  This is fixed using
device_unregister instead of device_destroy.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Newly added memory can not be accessed via /dev/mem, because we do not
update the variables high_memory, max_pfn and max_low_pfn.

Add a function update_end_of_memory_vars() to update these variables for
64-bit kernels.

[akpm@linux-foundation.org: simplify comment]
Signed-off-by: NShaohui Zheng <shaohui.zheng@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Li Haicheng <haicheng.li@intel.com>
Reviewed-by: NWu Fengguang <fengguang.wu@intel.com>
Reviewed-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

init_fault_attr_entries() should be init_fault_attr_dentries().

cleanup_fault_attr_entries() should be cleanup_fault_attr_dentries().
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

hugetlb_sysfs_add_hstate is called by hugetlb_register_node directly
during init and also indirectly via sysfs after init.

This patch removes the __init tag from hugetlb_sysfs_add_hstate.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>