- 27 10月, 2011 5 次提交
-
-
由 Ludovic Desroches 提交于
Rename atmci_start_command() to atmci_send_command() which is more appropriate; atmci_start_command suggests we're sending a start command. Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Ludovic Desroches 提交于
Add pdc support for atmel-mci. It makes at91-mci driver useless because it was only used for the old atmel MCI core which has pdc but no dma support. To allow removing at91-mci, the capabilities of the MCI core are detected at runtime -- then the driver will use pio, pdc or dma transfers. Warning: at91rm9200 is not supported, to support it we need to use swab32 on data but I have no board to test it. Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Ludovic Desroches 提交于
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Ludovic Desroches 提交于
Change atmci_readl and atmci_writel macros: remove string concatenation. We can use these macros with registers which are not prefixed by ATMCI_. This is the case if we want to write PDC registers which are common to several devices so they are not prefixed with ATMCI_. Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Ludovic Desroches 提交于
Homogenize namespace to atmci. Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
- 18 10月, 2011 1 次提交
-
- 17 10月, 2011 4 次提交
-
-
由 Michał Mirosław 提交于
Private rx_csum flags are now duplicate of netdev->features & NETIF_F_RXCSUM. Removing this needs deeper surgery. Things noticed: - HW VLAN acceleration probably can be toggled, but it's left as is - the resets on RX csum offload change can probably be avoided - there is A LOT of copy-and-pasted code here Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
When enabling hardware timestamping for ptp v2 event packets, the software does not setup the queue for l4 packets, although layer 4 packets are valid for v2. This patch adds the flag which enables setting up a queue and enabling udp packet timestamping. Signed-off-by: NJacob E Keller <jacob.e.keller@intel.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Greg Rose 提交于
Implements the new netdev op to allow user configuration of spoof checking on a per VF basis. V2 - Change netdev spoof check op setting to bool Signed-off-by: NGreg Rose <gregory.v.rose@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Greg Rose 提交于
Add configuration setting for drivers to turn spoof checking on or off for discrete VFs. v2 - Fix indentation problem, wrap the ifla_vf_info structure in #ifdef __KERNEL__ to prevent user space from accessing and change function paramater for the spoof check setting netdev op from u8 to bool. v3 - Preset spoof check setting to -1 so that user space tools such as ip can detect that the driver didn't report a spoofcheck setting. Prevents incorrect display of spoof check settings for drivers that don't report it. Signed-off-by: NGreg Rose <gregory.v.rose@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 16 10月, 2011 1 次提交
-
-
由 Bruce Allan 提交于
Commit 67fd4fcb (e1000e: convert to stats64) added the ability to update statistics more accurately and on-demand through the net_device_ops .ndo_get_stats64 hook, but introduced a locking bug on 82577/8/9 when linked at half-duplex (seen on kernels with CONFIG_DEBUG_ATOMIC_SLEEP=y and CONFIG_PROVE_LOCKING=y). The commit introduced code paths that caused a mutex to be locked in atomic contexts, e.g. an rcu_read_lock is held when irqbalance reads the stats from /sys/class/net/ethX/statistics causing the mutex to be locked to read the Phy half-duplex statistics registers. The mutex was originally introduced to prevent concurrent accesses of resources (the NVM and Phy) shared by the driver, firmware and hardware a few years back when there was an issue with the NVM getting corrupted. It was later split into two mutexes - one for the NVM and one for the Phy when it was determined the NVM, unlike the Phy, should not be protected by the software/firmware/hardware semaphore (arbitration of which is done in part with the SWFLAG bit in the EXTCNF_CTRL register). This latter semaphore should be sufficient to prevent resource contention of the Phy in the driver (i.e. the mutex for Phy accesses is not needed), but to be sure the mutex is replaced with an atomic bit flag which will warn if any contention is possible. Also add additional debug output to help determine when the sw/fw/hw semaphore is owned by the firmware or hardware. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Reported-by: NFrancois Romieu <romieu@fr.zoreil.com> Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
-
- 15 10月, 2011 29 次提交
-
-
由 Daniel Drake 提交于
The recent changes to only power the device when the interface up introduced a bug: changing interface type, legal when the interface is down, performs device I/O. Fix this functionality by validating and recording the interface type when the change is requested, but only applying the change if/when the interface is brought up. Signed-off-by: NDaniel Drake <dsd@laptop.org> Acked-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Helmut Schaa 提交于
Only station flags that are already defined in nl80211 are added for now. Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Helmut Schaa 提交于
Reuse the already existing struct nl80211_sta_flag_update to specify both, a flag mask and the flag set itself. This means nl80211_sta_flag_update is now used for setting station flags and also for getting station flags. Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The queue mapping/TID for non-QoS null data responses to is never set, making it default to BK. Fix that. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Renamed to be in sync with Marketing term and to avoid confusion with other chip names. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
The AR946/8x chips are 2x2 Dual band with BT support. In order to avoid misleading with other chips and to be in sync with marketing team's term, AR9480 is renamed as AR9462. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Support the fast channel change across band switch only when there are available of reusable cabliration results. And also observed that doing agc control calibration on fastcc, sometimes causing calibration timeout. Hence changing agc control to be run only on full chip reset. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Supported calibrations of radio retention table (RTT) are - DC offset - Filter - Peak detect Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
To improve sensitivity for AR9480, the normal and minimum noise floor values of both bands are updated. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
The commit "ath9k_hw: Improve fast channel change for AR9003 chips" fixes the fast channel change issue for AR9003 chips that was originally observed in AR9382 chip. Hence enabling fastcc support again for 11A channel for AR9003 chips. Cc: Paul Stewart <pstew@google.com> Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Currently Tx IQ calibration is enabled by default for all AR9003 chips. But for AR9480, the calibration status should be read from chip after processing ini. And also the carrier leak calibration status is checked during init cal. As the init_cal is being called for fast channel change too, the tx_cl status only be read after full reset. Hence moving that into process ini function. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
This patch adds support to reuse Carrier leak calibration during fast channel change for AR9480 chips. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Pass an argument to decide whether to reuse the Tx IQ calibration measurements or not during fast channel change. This will be later used by MCI support for AR9480. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
In order to reduce the overall scan time, fast channel change should be implemented properly. This patch adds fast channel change support across band switch or channel mode switch instead of doing full chip reset. During the fastcc, tx iqcal measurements are preserved and will be reloaded after successful the channel change. This patch also addressed fast channel issue where the STA can not see APs in higher than operating channel on 5GHz band after the association. Cc: Paul Stewart <pstew@google.com> Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
The 5G Tx gain table w/ XPA is updated to improve spur performance in high_power Tx gain table. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
The ar9003 table is updated to increase XLNA BIAS output driver strengh. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Because of not clearing Bit 14 of AR_WA, the ASPM L1 is not enabled when entering into sleep mode. AR9480 does not need bit 14 to be set. Cc: stable@kernel.org Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
This patch takes care of warnings found by running 'make namespacecheck': 1. Remove dead code. 2. Reorder function definitions to avoid forward declarations. 3. Remove unnecessary function/structure declarations and mark them as static. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Amitkumar Karwar 提交于
Currently global wait condition (adapter->cmd_wait_q.condition) is used while sending synchronous commands to FW. When two threads enter in mwifiex_send_cmd_sync() routine at the same time, both the threads wait for their command responses. Since wait condition is same for both, they wake up simultaneously after getting response of 1st command. After this when a thread is waiting for command response of 3rd command, it wakes up after getting response of 2nd command and so on. Therefore we don't wait for the response of last command(0xaa) during unload. Hence while next time loading the driver command time out is seen for INIT command. This problem is resolved by having separate wait condition flag for each command(except scan command). Since scan command is treated differently (by maintaining scan pending q etc.), newly defined flag (scan_wait_q_woken) is used as a scan wait condition. Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com> Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rafał Miłecki 提交于
This reverts commit 55ad5962. I assumed N is newer than LP, which isn't true. This regressed LP case. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stephen Rothwell 提交于
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Alwin Beukers 提交于
Wifi.c was empty after previous cleanups, so it was removed. Reviewed-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Alwin Beukers 提交于
Moved the brcmu_format_flags function and brcmu_bit_desc structure into smac. Names were adjusted accordingly. Reported-by: NJohannes Berg <johannes@sipsolutions.net> Reviewed-by: NRoland Vossen <rvossen@broadcom.com> Reviewed-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Alwin Beukers 提交于
Moved the brcmu_mkiovar function into fmac, adjusting the name accordingly. Reported-by: NJohannes Berg <johannes@sipsolutions.net> Reviewed-by: NRoland Vossen <rvossen@broadcom.com> Reviewed-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Alwin Beukers 提交于
Moved brcmu_chspec_malformed into the only file using it. The function name was adjusted accordingly. Reported-by: NJohannes Berg <johannes@sipsolutions.net> Reviewed-by: NRoland Vossen <rvossen@broadcom.com> Reviewed-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Alwin Beukers 提交于
Moved the brcmu_parse_tlvs function and brcmu_tlv structure into the only file using them. Names were adjusted accordingly. Reported-by: NJohannes Berg <johannes@sipsolutions.net> Reviewed-by: NRoland Vossen <rvossen@broadcom.com> Reviewed-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Alwin Beukers 提交于
Moved the brcmu_chipname function into the only file using it. The function name was adjusted accordingly. Reported-by: NJohannes Berg <johannes@sipsolutions.net> Reviewed-by: NRoland Vossen <rvossen@broadcom.com> Reviewed-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-