- 19 6月, 2012 1 次提交
-
-
由 Arik Nemtsov 提交于
While HW reconfig is in progress, drop all incoming Rx. This prevents incoming packets from changing the internal state of the driver or calling callbacks of the low level driver while it is in inconsistent state. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 18 6月, 2012 4 次提交
-
-
由 Chun-Yeow Yeoh 提交于
This patch fixes the wrong assignment of mesh element TTL. Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Chun-Yeow Yeoh 提交于
As defined in section 13.10.9.3 Case D (802.11-2012), this control variable is used to limit the mesh STA to send only one PREQ to a root mesh STA within this interval of time (in TUs). The default value for this variable is set to 2000 TUs. However, for current implementation, the maximum configurable of dot11MeshHWMPconfirmationInterval is restricted by dot11MeshHWMPactivePathTimeout. Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> [line-break commit log] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Chun-Yeow Yeoh 提交于
mesh_path_root_timer is invoked once the dot11MeshHWMPRootMode is larger than 1. This patch also adds the backward compatible to the previous setting on dot11MeshHWMPRootMode. If the user configures as follow, it will still trigger the proactive RANN with Gate Announcement. iw mesh0 set mesh_param mesh_hwmp_rootmode 1 iw mesh0 set mesh_param mesh_gate_announcements 1 similar to the following setting: iw mesh0 set mesh_param mesh_hwmp_rootmode 4 iw mesh0 set mesh_param mesh_gate_announcements 1 Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> [line-break commit log] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Chun-Yeow Yeoh 提交于
Generate the proactive PREP element in Proactive PREQ mode as defined in Sec. 13.10.10.3 (Case D) of IEEE Std. 802.11-2012. Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 14 6月, 2012 2 次提交
-
-
由 Chun-Yeow Yeoh 提交于
Generate the proactive PREQ element as defined in Sec. 13.10.9.3 (Case C) of IEEE Std. 802.11-2012 based on the selection of dot11MeshHWMPRootMode as follow: dot11MeshHWMPRootMode (2) is proactivePREQnoPREP dot11MeshHWMPRootMode (3) is proactivePREQwithPREP The proactive PREQ is generated based on the interval defined by dot11MeshHWMProotInterval. With this change, proactive RANN element is now generated if the dot11MeshHWMPRootMode is set to (4) instead of (1). Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> [line-break commit log] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Chun-Yeow Yeoh 提交于
Add the mesh configuration parameters dot11MeshHWMProotInterval and dot11MeshHWMPactivePathToRootTimeout to be used by proactive PREQ mechanism. Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> [line-break commit log] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 13 6月, 2012 4 次提交
-
-
由 Johannes Berg 提交于
Add missing entries to nl80211.h and fix the kernel-doc notation in cfg80211.h. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
It should be NL80211_SCHED_SCAN_MATCH_ATTR_SSID as documented, not NL80211_ATTR_SCHED_SCAN_MATCH_SSID. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Pontus Fuchs 提交于
If you add a monitor interface in parallel to a normal interface mac80211 will let you to change the channel type on the monitor interface even if you are connected. Add an explicit check to disallow this. Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com> [fix typo in commit log, use sdata instead of netdev] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
In my redesign of remain-on-channel I forgot that an item could be cancelled when it's a dependent item that is part of another item. Allow cancelling such items by removing them from the dependents list. Note that when we cancel the main item, all its dependents are also cancelled. It would be possible to not do that, but would need tricks to promote an item from dependent to top-level and is tricky in the HW ROC case. Reported-by: NIlan Peer <ilan.peer@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 12 6月, 2012 1 次提交
-
-
由 Avinash Patil 提交于
Reference: http://standards.ieee.org/develop/regauth/oui/oui.txtSigned-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 11 6月, 2012 3 次提交
-
-
由 Johannes Berg 提交于
Ilan pointed out to me that ieee80211_start_next_roc() already calls ieee80211_run_deferred_scan() if the list of ROC items is empty, so there's no need to call it again after calling ieee80211_start_next_roc(). Reported-by: NIlan Peer <ilan.peer@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Chun-Yeow Yeoh 提交于
fix the coding style related to mesh parameters, especially the indentation, as pointed out by Johannes Berg. Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Chun-Yeow Yeoh 提交于
Add the missing kernel-doc for mesh configuration parameters as pointed out by Johannes Berg. Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 09 6月, 2012 3 次提交
-
-
由 Javier Cardona 提交于
Signed-off-by: NJavier Cardona <javier@cozybit.com> Reviewed-by: NJason Abele <jason@cozybit.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Javier Cardona 提交于
Signed-off-by: NJavier Cardona <javier@cozybit.com> Reviewed-by: NJason Abele <jason@cozybit.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 John W. Linville 提交于
CC drivers/net/wireless/ti/wl18xx/main.o drivers/net/wireless/ti/wl18xx/main.c: In function ‘wl18xx_conf_init’: drivers/net/wireless/ti/wl18xx/main.c:1024:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 2 has type ‘long unsigned int’ [-Wformat] drivers/net/wireless/ti/wl18xx/main.c:1024:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t’ [-Wformat] Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 08 6月, 2012 15 次提交
-
-
由 Luciano Coelho 提交于
-
由 Arik Nemtsov 提交于
Don't spew errors when we can't find the NVS file in wlcore. Instead fail the wl12xx boot HW op if the NVS isn't found. Take this opportunity to remove some dead code from register_hw() which looks for the NVS again needlessly. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Arik Nemtsov 提交于
Give all wl18xx phy module paramters -1 as a default value, indicating the paramter was not set. Add previous default values to the default 18xx priv conf structure. Remove the board_type field from wl18xx priv. The field with the same name inside the phy conf is good enough for our purposes. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Arik Nemtsov 提交于
wl18xx_conf_phy represents part of the FW native wl18xx_mac_and_phy_params structure. Remove it and replace the phy part of the wl18xx conf with the FW bound structure. This allows us to set/override all members. Increment the wlconf version to ensure compatibility with the new structure Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Ido Reis 提交于
Aligned to the struct in FW 8.2.0.0.91 and updated the debugfs entries accordingly. Signed-off-by: NIdo Reis <idor@ti.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Arik Nemtsov 提交于
This is supported by new FW versions (.88+). Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Luciano Coelho 提交于
Instead of using the hardcoded configuration structure, try to read it from a "firmware" file called wl18xx-conf.bin. If the file doesn't exist, fall back to the hardcoded version. If the file exists but is illegal, bail out. Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Luciano Coelho 提交于
Add conf file header structure, magic and version values and export the entire conf struct in debugfs. Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Luciano Coelho 提交于
Since we are now going to export the conf structure and read it from a file, it should be packed to avoid surprises with padding bytes. Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Luciano Coelho 提交于
Since we will export the conf structure as a file, we need to use well defined types. Instead of using enum, whose size may vary, use u8 for bcn_filt_mode instead. Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Luciano Coelho 提交于
The conf structure is going to be exported to a file, so we should use only well defined types. bool is not well defined and may vary from platform to platform, so change the host_fast_wakeup_support type to u8 instead. Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Luciano Coelho 提交于
Instead of parsing all the binary data returned by the firmware, we should simply export the binary and let the userspace do the parsing. This commit adds a new file to debugfs to do that. Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Luciano Coelho 提交于
This patch calls ACX_CLEAR_STATISTICS to clear the firmware statistics. The trigger is a new debugfs file called clear_fw_statistics in the fw_stats directory. Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Eyal Shapira 提交于
Add control over several conf fields which combined control the rx interrupt pacing mechanism, that is avoiding getting an interrupt following a single frame rx but instead have the FW trigger the interrupt only after a certain amount of frames received or a timeout. Signed-off-by: NEyal Shapira <eyal@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Eyal Shapira 提交于
The current debugfs code contains too much code duplication of bolierplate code. Add some macro magic to avoid this and enable adding new debugfs entries by using just a few lines. Signed-off-by: NEyal Shapira <eyal@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
- 07 6月, 2012 7 次提交
-
-
由 Grant Erickson 提交于
Add support for an external 26 MHz crystal source. [Changed wl->ref_clock to priv->ref_clock -- Luca.] Signed-off-by: NGrant Erickson <marathon96@gmail.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Ido Reis 提交于
In PG2 only the last frame in the aggregate buffer should be aligned to the sdio block size. This frame's header msb should be set to 0, while in all the previous frames in the aggregation buffer, this bit should be set to 1. [Add a HW op for setting the frame ctrl bit only for 18xx. Other minor cleanups - Arik] [Make the pre_pkt_send operation optional -- Luca] Signed-off-by: NIdo Reis <idor@ti.com> Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Ido Reis 提交于
In PG2, the HW watchdog interrupt occupies bit0 of the event vector, and the SW watchdog is relocated to bit9. We perform the relocation globally, as there's only one watchdog bit on previous platforms (bit0). [Only mask in the new bit9 for platforms supporting it. This avoids spurious events on other platforms - Arik] Signed-off-by: NOrit Brayer <orit@ti.com> Signed-off-by: NIdo Reis <idor@ti.com> Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Ido Reis 提交于
PG2 requires 4 new parameters that to be passed to the PHY. Use the actual PHY initialization struct size for the mem size of the PHY_INIT section, to account for additions in params. [Make sure PG1 still gets the original struct - Arik] Signed-off-by: NIdo Reis <idor@ti.com> Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Ido Reis 提交于
PG2 has a unique chip id. It supports similar HW quirks. Signed-off-by: NIdo Reis <idor@ti.com> Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Ido Reis 提交于
was hardcoded 252, now uses the parameters struct size. Signed-off-by: NIdo Reis <idor@ti.com> Signed-off-by: NLuciano Coelho <coelho@ti.com>
-
由 Johannes Berg 提交于
Redesign all the off-channel code, getting rid of the generic off-channel work concept, replacing it with a simple remain-on-channel list. This fixes a number of small issues with the ROC implementation: * offloaded remain-on-channel couldn't be queued, now we can queue it as well, if needed * in iwlwifi (the only user) offloaded ROC is mutually exclusive with scanning, use the new queue to handle that case -- I expect that it will later depend on a HW flag The bigger issue though is that there's a bad bug in the current implementation: if we get a mgmt TX request while HW roc is active, and this new request has a wait time, we actually schedule a software ROC instead since we can't guarantee the existing offloaded ROC will still be that long. To fix this, the queuing mechanism was needed. The queuing mechanism for offloaded ROC isn't yet optimal, ideally we should add API to have the HW extend the ROC if needed. We could add that later but for now use a software implementation. Overall, this unifies the behaviour between the offloaded and software-implemented case as much as possible. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-