提交 e6d92e63 编写于 作者: A Andrew Victor 提交者: Russell King

[ARM] 4146/1: AT91: Support for AT91SAM9263-EK board.

Add support for the Atmel AT91SAM9263-EK board.

Original patch from Nicolas Ferre.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
上级 b2c65616
此差异已折叠。
......@@ -121,17 +121,32 @@ endif
# ----------------------------------------------------------
if ARCH_AT91SAM9263
comment "AT91SAM9263 Board Type"
config MACH_AT91SAM9263EK
bool "Atmel AT91SAM9263-EK Evaluation Kit"
depends on ARCH_AT91SAM9263
help
Select this if you are using Atmel's AT91SAM9263-EK Evaluation Kit.
<http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4057>
endif
# ----------------------------------------------------------
comment "AT91 Board Options"
config MTD_AT91_DATAFLASH_CARD
bool "Enable DataFlash Card support"
depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK)
depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK)
help
Enable support for the DataFlash card.
config MTD_NAND_AT91_BUSWIDTH_16
bool "Enable 16-bit data bus interface to NAND flash"
depends on (MACH_AT91SAM9261EK || MACH_AT91SAM9260EK)
depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK)
help
On AT91SAM926x boards both types of NAND flash can be present
(8 and 16 bit data bus width).
......
......@@ -32,6 +32,9 @@ obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o
# AT91SAM9261 board-specific support
obj-$(CONFIG_MACH_AT91SAM9261EK) += board-sam9261ek.o
# AT91SAM9263 board-specific support
obj-$(CONFIG_MACH_AT91SAM9263EK) += board-sam9263ek.o
# LEDs support
led-$(CONFIG_ARCH_AT91RM9200DK) += leds.o
led-$(CONFIG_MACH_AT91RM9200EK) += leds.o
......
/*
* linux/arch/arm/mach-at91/board-sam9263ek.c
*
* Copyright (C) 2005 SAN People
* Copyright (C) 2007 Atmel Corporation.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <asm/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/arch/board.h>
#include <asm/arch/gpio.h>
#include <asm/arch/at91sam926x_mc.h>
#include "generic.h"
/*
* Serial port configuration.
* 0 .. 2 = USART0 .. USART2
* 3 = DBGU
*/
static struct at91_uart_config __initdata ek_uart_config = {
.console_tty = 0, /* ttyS0 */
.nr_tty = 2,
.tty_map = { 3, 0, -1, -1, } /* ttyS0, ..., ttyS3 */
};
static void __init ek_map_io(void)
{
/* Initialize processor: 16.367 MHz crystal */
at91sam9263_initialize(16367660);
/* Setup the serial ports and console */
at91_init_serial(&ek_uart_config);
}
static void __init ek_init_irq(void)
{
at91sam9263_init_interrupts(NULL);
}
/*
* USB Host port
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
};
/*
* USB Device port
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PA25,
.pullup_pin = 0, /* pull-up driven by UDC */
};
/*
* SPI devices.
*/
static struct spi_board_info ek_spi_devices[] = {
#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
{ /* DataFlash card */
.modalias = "mtd_dataflash",
.chip_select = 0,
.max_speed_hz = 15 * 1000 * 1000,
.bus_num = 0,
},
#endif
};
/*
* MCI (SD/MMC)
*/
static struct at91_mmc_data __initdata ek_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PE18,
.wp_pin = AT91_PIN_PE19,
// .vcc_pin = ... not connected
};
/*
* NAND flash
*/
static struct mtd_partition __initdata ek_nand_partition[] = {
{
.name = "Partition 1",
.offset = 0,
.size = 64 * 1024 * 1024,
},
{
.name = "Partition 2",
.offset = 64 * 1024 * 1024,
.size = MTDPART_SIZ_FULL,
},
};
static struct mtd_partition *nand_partitions(int size, int *num_partitions)
{
*num_partitions = ARRAY_SIZE(ek_nand_partition);
return ek_nand_partition;
}
static struct at91_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.rdy_pin = AT91_PIN_PA22,
.enable_pin = AT91_PIN_PD15,
.partition_info = nand_partitions,
#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#endif
};
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* MMC */
at91_add_device_mmc(1, &ek_mmc_data);
/* NAND */
at91_add_device_nand(&ek_nand_data);
}
MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
/* Maintainer: Atmel */
.phys_io = AT91_BASE_SYS,
.io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
.boot_params = AT91_SDRAM_BASE + 0x100,
.timer = &at91sam926x_timer,
.map_io = ek_map_io,
.init_irq = ek_init_irq,
.init_machine = ek_board_init,
MACHINE_END
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册