Merge tag 'spi-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "The nicest things about this release for me is seeing some older
  drivers getting some cleanups and modernization, it's really good to
  see things moving forwards even for older drivers.

  In content terms it's a fairly humdrum release but where the work has
  been happening is great.

   - Support for simultaneous use of internal and GPIO chip selects for
     devices that require the use of the internal select even if it's
     not connected and a GPIO is actually routed to the slave device.

   - A major rework and cleanup of the fsl-espi driver from Heiner
     Kallweit which should make it work substantially better.

   - DMA support for Freescale DSPI IPs.

   - New drivers for Freescale LPSPI IPs and Marvell Armada 3700.

   - Support for Allwinner H3"

* tag 'spi-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (85 commits)
  spi: mvebu: fix baudrate calculation for armada variant
  spi: Add support for Armada 3700 SPI Controller
  spi: armada-3700: Add documentation for the Armada 3700 SPI Controller
  spi: fsl-lpspi: quit reading rx fifo under error condition
  spi: fsl-lpspi: use GPL as module license
  spi: fsl-espi: fix ioread16/iowrite16 endianness
  spi: fsl-espi: remove unused linearization code
  spi: fsl-espi: eliminate need for linearization when reading from hardware
  spi: fsl-espi: eliminate need for linearization when writing to hardware
  spi: fsl-espi: determine need for byte swap only once
  spi: fsl-lpspi: read lpspi tx/rx fifo size in probe()
  spi: fsl-lpspi: use wait_for_completion_timeout() while waiting transfer done
  spi: orion: fix comment to mention MVEBU
  spi: atmel: remove the use of private channel fields
  spi: atmel: trivial: remove unused fields in DMA structure
  spi: atmel: Use SPI core DMA mapping framework
  spi: atmel: Use core SPI_MASTER_MUST_[RT]X handling
  spi: atmel: trivial: move info banner to latest probe action
  spi: imx: replace schedule() with cond_resched()
  spi: imx: fix potential shift truncation
  ...

Documentation/devicetree/bindings/spi/sh-msiof.txt

@@ -10,6 +10,7 @@ Required properties:
 			 "renesas,msiof-r8a7792" (R-Car V2H)
 			 "renesas,msiof-r8a7793" (R-Car M2-N)
 			 "renesas,msiof-r8a7794" (R-Car E2)
+			 "renesas,msiof-r8a7796" (R-Car M3-W)
 			 "renesas,msiof-sh73a0" (SH-Mobile AG5)
 - reg                  : A list of offsets and lengths of the register sets for
 			 the device.

Documentation/devicetree/bindings/spi/spi-armada-3700.txt

+* Marvell Armada 3700 SPI Controller
+
+Required Properties:
+
+- compatible: should be "marvell,armada-3700-spi"
+- reg: physical base address of the controller and length of memory mapped
+       region.
+- interrupts: The interrupt number. The interrupt specifier format depends on
+	      the interrupt controller and of its driver.
+- clocks: Must contain the clock source, usually from the North Bridge clocks.
+- num-cs: The number of chip selects that is supported by this SPI Controller
+- #address-cells: should be 1.
+- #size-cells: should be 0.
+
+Example:
+
+	spi0: spi@10600 {
+		compatible = "marvell,armada-3700-spi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10600 0x5d>;
+		clocks = <&nb_perih_clk 7>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+		num-cs = <4>;
+	};

Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt

+* Freescale Low Power SPI (LPSPI) for i.MX
+
+Required properties:
+- compatible :
+  - "fsl,imx7ulp-spi" for LPSPI compatible with the one integrated on i.MX7ULP soc
+- reg : address and length of the lpspi master registers
+- interrupt-parent : core interrupt controller
+- interrupts : lpspi interrupt
+- clocks : lpspi clock specifier
+
+Examples:
+
+lpspi2: lpspi@40290000 {
+	compatible = "fsl,imx7ulp-spi";
+	reg = <0x40290000 0x10000>;
+	interrupt-parent = <&intc>;
+	interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&clks IMX7ULP_CLK_LPSPI2>;
+};

Documentation/devicetree/bindings/spi/spi-sun6i.txt

-Allwinner A31 SPI controller
+Allwinner A31/H3 SPI controller
 
 Required properties:
-- compatible: Should be "allwinner,sun6i-a31-spi".
+- compatible: Should be "allwinner,sun6i-a31-spi" or "allwinner,sun8i-h3-spi".
 - reg: Should contain register location and length.
 - interrupts: Should contain interrupt.
 - clocks: phandle to the clocks feeding the SPI controller. Two are
@@ -12,6 +12,11 @@ Required properties:
 - resets: phandle to the reset controller asserting this device in
           reset
 
+Optional properties:
+- dmas: DMA specifiers for rx and tx dma. See the DMA client binding,
+	Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: DMA request names should include "rx" and "tx" if present.
+
 Example:
 
 spi1: spi@01c69000 {
@@ -22,3 +27,19 @@ spi1: spi@01c69000 {
 	clock-names = "ahb", "mod";
 	resets = <&ahb1_rst 21>;
 };
+
+spi0: spi@01c68000 {
+	compatible = "allwinner,sun8i-h3-spi";
+	reg = <0x01c68000 0x1000>;
+	interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+	clock-names = "ahb", "mod";
+	dmas = <&dma 23>, <&dma 23>;
+	dma-names = "rx", "tx";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	resets = <&ccu RST_BUS_SPI0>;
+	status = "disabled";
+	#address-cells = <1>;
+	#size-cells = <0>;
+};

drivers/spi/Kconfig

@@ -67,6 +67,13 @@ config SPI_ATH79
 	  This enables support for the SPI controller present on the
 	  Atheros AR71XX/AR724X/AR913X SoCs.
 
+config SPI_ARMADA_3700
+	tristate "Marvell Armada 3700 SPI Controller"
+	depends on (ARCH_MVEBU && OF) || COMPILE_TEST
+	help
+	  This enables support for the SPI controller present on the
+	  Marvell Armada 3700 SoCs.
+
 config SPI_ATMEL
 	tristate "Atmel SPI Controller"
 	depends on HAS_DMA
@@ -264,6 +271,12 @@ config SPI_FALCON
 	  has only been tested with m25p80 type chips. The hardware has no
 	  support for other types of SPI peripherals.
 
+config SPI_FSL_LPSPI
+	tristate "Freescale i.MX LPSPI controller"
+	depends on ARCH_MXC || COMPILE_TEST
+	help
+	  This enables Freescale i.MX LPSPI controllers in master mode.
+
 config SPI_GPIO
 	tristate "GPIO-based bitbanging SPI Master"
 	depends on GPIOLIB || COMPILE_TEST
@@ -373,7 +386,6 @@ config SPI_FSL_DSPI
 config SPI_FSL_ESPI
 	tristate "Freescale eSPI controller"
 	depends on FSL_SOC
-	select SPI_FSL_LIB
 	help
 	  This enables using the Freescale eSPI controllers in master mode.
 	  From MPC8536, 85xx platform uses the controller, and all P10xx,
@@ -451,7 +463,8 @@ config SPI_ORION
 	tristate "Orion SPI master"
 	depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
 	help
-	  This enables using the SPI master controller on the Orion chips.
+	  This enables using the SPI master controller on the Orion
+	  and MVEBU chips.
 
 config SPI_PIC32
 	tristate "Microchip PIC32 series SPI"
@@ -553,7 +566,7 @@ config SPI_S3C24XX_FIQ
 
 config SPI_S3C64XX
 	tristate "Samsung S3C64XX series type SPI"
-	depends on (PLAT_SAMSUNG || ARCH_EXYNOS)
+	depends on (PLAT_SAMSUNG || ARCH_EXYNOS || COMPILE_TEST)
 	help
 	  SPI driver for Samsung S3C64XX and newer SoCs.
 

drivers/spi/Makefile

@@ -12,6 +12,7 @@ obj-$(CONFIG_SPI_LOOPBACK_TEST)		+= spi-loopback-test.o
 
 # SPI master controller drivers (bus)
 obj-$(CONFIG_SPI_ALTERA)		+= spi-altera.o
+obj-$(CONFIG_SPI_ARMADA_3700)		+= spi-armada-3700.o
 obj-$(CONFIG_SPI_ATMEL)			+= spi-atmel.o
 obj-$(CONFIG_SPI_ATH79)			+= spi-ath79.o
 obj-$(CONFIG_SPI_AU1550)		+= spi-au1550.o
@@ -43,6 +44,7 @@ obj-$(CONFIG_SPI_FSL_CPM)		+= spi-fsl-cpm.o
 obj-$(CONFIG_SPI_FSL_DSPI)		+= spi-fsl-dspi.o
 obj-$(CONFIG_SPI_FSL_LIB)		+= spi-fsl-lib.o
 obj-$(CONFIG_SPI_FSL_ESPI)		+= spi-fsl-espi.o
+obj-$(CONFIG_SPI_FSL_LPSPI)		+= spi-fsl-lpspi.o
 obj-$(CONFIG_SPI_FSL_SPI)		+= spi-fsl-spi.o
 obj-$(CONFIG_SPI_GPIO)			+= spi-gpio.o
 obj-$(CONFIG_SPI_IMG_SPFI)		+= spi-img-spfi.o

drivers/spi/spi-ath79.c

@@ -304,6 +304,7 @@ static const struct of_device_id ath79_spi_of_match[] = {
 	{ .compatible = "qca,ar7100-spi", },
 	{ },
 };
+MODULE_DEVICE_TABLE(of, ath79_spi_of_match);
 
 static struct platform_driver ath79_spi_driver = {
 	.probe		= ath79_spi_probe,

drivers/spi/spi-atmel.c

@@ -24,6 +24,7 @@
 
 #include <linux/io.h>
 #include <linux/gpio.h>
+#include <linux/of_gpio.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/pm_runtime.h>
 
@@ -264,17 +265,6 @@
 
 #define AUTOSUSPEND_TIMEOUT	2000
 
-struct atmel_spi_dma {
-	struct dma_chan			*chan_rx;
-	struct dma_chan			*chan_tx;
-	struct scatterlist		sgrx;
-	struct scatterlist		sgtx;
-	struct dma_async_tx_descriptor	*data_desc_rx;
-	struct dma_async_tx_descriptor	*data_desc_tx;
-
-	struct at_dma_slave	dma_slave;
-};
-
 struct atmel_spi_caps {
 	bool	is_spi2;
 	bool	has_wdrbt;
@@ -295,6 +285,7 @@ struct atmel_spi {
 	int			irq;
 	struct clk		*clk;
 	struct platform_device	*pdev;
+	unsigned long		spi_clk;
 
 	struct spi_transfer	*current_transfer;
 	int			current_remaining_bytes;
@@ -302,17 +293,11 @@ struct atmel_spi {
 
 	struct completion	xfer_completion;
 
-	/* scratch buffer */
-	void			*buffer;
-	dma_addr_t		buffer_dma;
-
 	struct atmel_spi_caps	caps;
 
 	bool			use_dma;
 	bool			use_pdc;
 	bool			use_cs_gpios;
-	/* dmaengine data */
-	struct atmel_spi_dma	dma;
 
 	bool			keep_cs;
 	bool			cs_active;
@@ -326,7 +311,7 @@ struct atmel_spi_device {
 	u32			csr;
 };
 
-#define BUFFER_SIZE		PAGE_SIZE
+#define SPI_MAX_DMA_XFER	65535 /* true for both PDC and DMA */
 #define INVALID_DMA_ADDRESS	0xffffffff
 
 /*
@@ -456,10 +441,20 @@ static inline bool atmel_spi_use_dma(struct atmel_spi *as,
 	return as->use_dma && xfer->len >= DMA_MIN_BYTES;
 }
 
+static bool atmel_spi_can_dma(struct spi_master *master,
+			      struct spi_device *spi,
+			      struct spi_transfer *xfer)
+{
+	struct atmel_spi *as = spi_master_get_devdata(master);
+
+	return atmel_spi_use_dma(as, xfer);
+}
+
 static int atmel_spi_dma_slave_config(struct atmel_spi *as,
 				struct dma_slave_config *slave_config,
 				u8 bits_per_word)
 {
+	struct spi_master *master = platform_get_drvdata(as->pdev);
 	int err = 0;
 
 	if (bits_per_word > 8) {
@@ -491,7 +486,7 @@ static int atmel_spi_dma_slave_config(struct atmel_spi *as,
 	 * path works the same whether FIFOs are available (and enabled) or not.
 	 */
 	slave_config->direction = DMA_MEM_TO_DEV;
-	if (dmaengine_slave_config(as->dma.chan_tx, slave_config)) {
+	if (dmaengine_slave_config(master->dma_tx, slave_config)) {
 		dev_err(&as->pdev->dev,
 			"failed to configure tx dma channel\n");
 		err = -EINVAL;
@@ -506,7 +501,7 @@ static int atmel_spi_dma_slave_config(struct atmel_spi *as,
 	 * enabled) or not.
 	 */
 	slave_config->direction = DMA_DEV_TO_MEM;
-	if (dmaengine_slave_config(as->dma.chan_rx, slave_config)) {
+	if (dmaengine_slave_config(master->dma_rx, slave_config)) {
 		dev_err(&as->pdev->dev,
 			"failed to configure rx dma channel\n");
 		err = -EINVAL;
@@ -515,7 +510,8 @@ static int atmel_spi_dma_slave_config(struct atmel_spi *as,
 	return err;
 }
 
-static int atmel_spi_configure_dma(struct atmel_spi *as)
+static int atmel_spi_configure_dma(struct spi_master *master,
+				   struct atmel_spi *as)
 {
 	struct dma_slave_config	slave_config;
 	struct device *dev = &as->pdev->dev;
@@ -525,26 +521,26 @@ static int atmel_spi_configure_dma(struct atmel_spi *as)
 	dma_cap_zero(mask);
 	dma_cap_set(DMA_SLAVE, mask);
 
-	as->dma.chan_tx = dma_request_slave_channel_reason(dev, "tx");
-	if (IS_ERR(as->dma.chan_tx)) {
-		err = PTR_ERR(as->dma.chan_tx);
+	master->dma_tx = dma_request_slave_channel_reason(dev, "tx");
+	if (IS_ERR(master->dma_tx)) {
+		err = PTR_ERR(master->dma_tx);
 		if (err == -EPROBE_DEFER) {
 			dev_warn(dev, "no DMA channel available at the moment\n");
-			return err;
+			goto error_clear;
 		}
 		dev_err(dev,
 			"DMA TX channel not available, SPI unable to use DMA\n");
 		err = -EBUSY;
-		goto error;
+		goto error_clear;
 	}
 
 	/*
 	 * No reason to check EPROBE_DEFER here since we have already requested
 	 * tx channel. If it fails here, it's for another reason.
 	 */
-	as->dma.chan_rx = dma_request_slave_channel(dev, "rx");
+	master->dma_rx = dma_request_slave_channel(dev, "rx");
 
-	if (!as->dma.chan_rx) {
+	if (!master->dma_rx) {
 		dev_err(dev,
 			"DMA RX channel not available, SPI unable to use DMA\n");
 		err = -EBUSY;
@@ -557,31 +553,38 @@ static int atmel_spi_configure_dma(struct atmel_spi *as)
 
 	dev_info(&as->pdev->dev,
 			"Using %s (tx) and %s (rx) for DMA transfers\n",
-			dma_chan_name(as->dma.chan_tx),
-			dma_chan_name(as->dma.chan_rx));
+			dma_chan_name(master->dma_tx),
+			dma_chan_name(master->dma_rx));
+
 	return 0;
 error:
-	if (as->dma.chan_rx)
-		dma_release_channel(as->dma.chan_rx);
-	if (!IS_ERR(as->dma.chan_tx))
-		dma_release_channel(as->dma.chan_tx);
+	if (master->dma_rx)
+		dma_release_channel(master->dma_rx);
+	if (!IS_ERR(master->dma_tx))
+		dma_release_channel(master->dma_tx);
+error_clear:
+	master->dma_tx = master->dma_rx = NULL;
 	return err;
 }
 
-static void atmel_spi_stop_dma(struct atmel_spi *as)
+static void atmel_spi_stop_dma(struct spi_master *master)
 {
-	if (as->dma.chan_rx)
-		dmaengine_terminate_all(as->dma.chan_rx);
-	if (as->dma.chan_tx)
-		dmaengine_terminate_all(as->dma.chan_tx);
+	if (master->dma_rx)
+		dmaengine_terminate_all(master->dma_rx);
+	if (master->dma_tx)
+		dmaengine_terminate_all(master->dma_tx);
 }
 
-static void atmel_spi_release_dma(struct atmel_spi *as)
+static void atmel_spi_release_dma(struct spi_master *master)
 {
-	if (as->dma.chan_rx)
-		dma_release_channel(as->dma.chan_rx);
-	if (as->dma.chan_tx)
-		dma_release_channel(as->dma.chan_tx);
+	if (master->dma_rx) {
+		dma_release_channel(master->dma_rx);
+		master->dma_rx = NULL;
+	}
+	if (master->dma_tx) {
+		dma_release_channel(master->dma_tx);
+		master->dma_tx = NULL;
+	}
 }
 
 /* This function is called by the DMA driver from tasklet context */
@@ -611,14 +614,10 @@ static void atmel_spi_next_xfer_single(struct spi_master *master,
 		cpu_relax();
 	}
 
-	if (xfer->tx_buf) {
-		if (xfer->bits_per_word > 8)
-			spi_writel(as, TDR, *(u16 *)(xfer->tx_buf + xfer_pos));
-		else
-			spi_writel(as, TDR, *(u8 *)(xfer->tx_buf + xfer_pos));
-	} else {
-		spi_writel(as, TDR, 0);
-	}
+	if (xfer->bits_per_word > 8)
+		spi_writel(as, TDR, *(u16 *)(xfer->tx_buf + xfer_pos));
+	else
+		spi_writel(as, TDR, *(u8 *)(xfer->tx_buf + xfer_pos));
 
 	dev_dbg(master->dev.parent,
 		"  start pio xfer %p: len %u tx %p rx %p bitpw %d\n",
@@ -665,17 +664,12 @@ static void atmel_spi_next_xfer_fifo(struct spi_master *master,
 
 	/* Fill TX FIFO */
 	while (num_data >= 2) {
-		if (xfer->tx_buf) {
-			if (xfer->bits_per_word > 8) {
-				td0 = *words++;
-				td1 = *words++;
-			} else {
-				td0 = *bytes++;
-				td1 = *bytes++;
-			}
+		if (xfer->bits_per_word > 8) {
+			td0 = *words++;
+			td1 = *words++;
 		} else {
-			td0 = 0;
-			td1 = 0;
+			td0 = *bytes++;
+			td1 = *bytes++;
 		}
 
 		spi_writel(as, TDR, (td1 << 16) | td0);
@@ -683,14 +677,10 @@ static void atmel_spi_next_xfer_fifo(struct spi_master *master,
 	}
 
 	if (num_data) {
-		if (xfer->tx_buf) {
-			if (xfer->bits_per_word > 8)
-				td0 = *words++;
-			else
-				td0 = *bytes++;
-		} else {
-			td0 = 0;
-		}
+		if (xfer->bits_per_word > 8)
+			td0 = *words++;
+		else
+			td0 = *bytes++;
 
 		spi_writew(as, TDR, td0);
 		num_data--;
@@ -730,13 +720,12 @@ static int atmel_spi_next_xfer_dma_submit(struct spi_master *master,
 				u32 *plen)
 {
 	struct atmel_spi	*as = spi_master_get_devdata(master);
-	struct dma_chan		*rxchan = as->dma.chan_rx;
-	struct dma_chan		*txchan = as->dma.chan_tx;
+	struct dma_chan		*rxchan = master->dma_rx;
+	struct dma_chan		*txchan = master->dma_tx;
 	struct dma_async_tx_descriptor *rxdesc;
 	struct dma_async_tx_descriptor *txdesc;
 	struct dma_slave_config	slave_config;
 	dma_cookie_t		cookie;
-	u32	len = *plen;
 
 	dev_vdbg(master->dev.parent, "atmel_spi_next_xfer_dma_submit\n");
 
@@ -747,44 +736,22 @@ static int atmel_spi_next_xfer_dma_submit(struct spi_master *master,
 	/* release lock for DMA operations */
 	atmel_spi_unlock(as);
 
-	/* prepare the RX dma transfer */
-	sg_init_table(&as->dma.sgrx, 1);
-	if (xfer->rx_buf) {
-		as->dma.sgrx.dma_address = xfer->rx_dma + xfer->len - *plen;
-	} else {
-		as->dma.sgrx.dma_address = as->buffer_dma;
-		if (len > BUFFER_SIZE)
-			len = BUFFER_SIZE;
-	}
-
-	/* prepare the TX dma transfer */
-	sg_init_table(&as->dma.sgtx, 1);
-	if (xfer->tx_buf) {
-		as->dma.sgtx.dma_address = xfer->tx_dma + xfer->len - *plen;
-	} else {
-		as->dma.sgtx.dma_address = as->buffer_dma;
-		if (len > BUFFER_SIZE)
-			len = BUFFER_SIZE;
-		memset(as->buffer, 0, len);
-	}
-
-	sg_dma_len(&as->dma.sgtx) = len;
-	sg_dma_len(&as->dma.sgrx) = len;
-
-	*plen = len;
+	*plen = xfer->len;
 
 	if (atmel_spi_dma_slave_config(as, &slave_config,
 				       xfer->bits_per_word))
 		goto err_exit;
 
 	/* Send both scatterlists */
-	rxdesc = dmaengine_prep_slave_sg(rxchan, &as->dma.sgrx, 1,
+	rxdesc = dmaengine_prep_slave_sg(rxchan,
+					 xfer->rx_sg.sgl, xfer->rx_sg.nents,
 					 DMA_FROM_DEVICE,
 					 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 	if (!rxdesc)
 		goto err_dma;
 
-	txdesc = dmaengine_prep_slave_sg(txchan, &as->dma.sgtx, 1,
+	txdesc = dmaengine_prep_slave_sg(txchan,
+					 xfer->tx_sg.sgl, xfer->tx_sg.nents,
 					 DMA_TO_DEVICE,
 					 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 	if (!txdesc)
@@ -818,7 +785,7 @@ static int atmel_spi_next_xfer_dma_submit(struct spi_master *master,
 
 err_dma:
 	spi_writel(as, IDR, SPI_BIT(OVRES));
-	atmel_spi_stop_dma(as);
+	atmel_spi_stop_dma(master);
 err_exit:
 	atmel_spi_lock(as);
 	return -ENOMEM;
@@ -830,30 +797,10 @@ static void atmel_spi_next_xfer_data(struct spi_master *master,
 				dma_addr_t *rx_dma,
 				u32 *plen)
 {
-	struct atmel_spi	*as = spi_master_get_devdata(master);
-	u32			len = *plen;
-
-	/* use scratch buffer only when rx or tx data is unspecified */
-	if (xfer->rx_buf)
-		*rx_dma = xfer->rx_dma + xfer->len - *plen;
-	else {
-		*rx_dma = as->buffer_dma;
-		if (len > BUFFER_SIZE)
-			len = BUFFER_SIZE;
-	}
-
-	if (xfer->tx_buf)
-		*tx_dma = xfer->tx_dma + xfer->len - *plen;
-	else {
-		*tx_dma = as->buffer_dma;
-		if (len > BUFFER_SIZE)
-			len = BUFFER_SIZE;
-		memset(as->buffer, 0, len);
-		dma_sync_single_for_device(&as->pdev->dev,
-				as->buffer_dma, len, DMA_TO_DEVICE);
-	}
-
-	*plen = len;
+	*rx_dma = xfer->rx_dma + xfer->len - *plen;
+	*tx_dma = xfer->tx_dma + xfer->len - *plen;
+	if (*plen > master->max_dma_len)
+		*plen = master->max_dma_len;
 }
 
 static int atmel_spi_set_xfer_speed(struct atmel_spi *as,
@@ -864,7 +811,7 @@ static int atmel_spi_set_xfer_speed(struct atmel_spi *as,
 	unsigned long		bus_hz;
 
 	/* v1 chips start out at half the peripheral bus speed. */
-	bus_hz = clk_get_rate(as->clk);
+	bus_hz = as->spi_clk;
 	if (!atmel_spi_is_v2(as))
 		bus_hz /= 2;
 
@@ -1025,16 +972,12 @@ atmel_spi_pump_single_data(struct atmel_spi *as, struct spi_transfer *xfer)
 	u16		*rxp16;
 	unsigned long	xfer_pos = xfer->len - as->current_remaining_bytes;
 
-	if (xfer->rx_buf) {
-		if (xfer->bits_per_word > 8) {
-			rxp16 = (u16 *)(((u8 *)xfer->rx_buf) + xfer_pos);
-			*rxp16 = spi_readl(as, RDR);
-		} else {
-			rxp = ((u8 *)xfer->rx_buf) + xfer_pos;
-			*rxp = spi_readl(as, RDR);
-		}
+	if (xfer->bits_per_word > 8) {
+		rxp16 = (u16 *)(((u8 *)xfer->rx_buf) + xfer_pos);
+		*rxp16 = spi_readl(as, RDR);
 	} else {
-		spi_readl(as, RDR);
+		rxp = ((u8 *)xfer->rx_buf) + xfer_pos;
+		*rxp = spi_readl(as, RDR);
 	}
 	if (xfer->bits_per_word > 8) {
 		if (as->current_remaining_bytes > 2)
@@ -1073,12 +1016,10 @@ atmel_spi_pump_fifo_data(struct atmel_spi *as, struct spi_transfer *xfer)
 	/* Read data */
 	while (num_data) {
 		rd = spi_readl(as, RDR);
-		if (xfer->rx_buf) {
-			if (xfer->bits_per_word > 8)
-				*words++ = rd;
-			else
-				*bytes++ = rd;
-		}
+		if (xfer->bits_per_word > 8)
+			*words++ = rd;
+		else
+			*bytes++ = rd;
 		num_data--;
 	}
 }
@@ -1204,7 +1145,6 @@ static int atmel_spi_setup(struct spi_device *spi)
 	u32			csr;
 	unsigned int		bits = spi->bits_per_word;
 	unsigned int		npcs_pin;
-	int			ret;
 
 	as = spi_master_get_devdata(spi->master);
 
@@ -1247,16 +1187,9 @@ static int atmel_spi_setup(struct spi_device *spi)
 		if (!asd)
 			return -ENOMEM;
 
-		if (as->use_cs_gpios) {
-			ret = gpio_request(npcs_pin, dev_name(&spi->dev));
-			if (ret) {
-				kfree(asd);
-				return ret;
-			}
-
+		if (as->use_cs_gpios)
 			gpio_direction_output(npcs_pin,
 					      !(spi->mode & SPI_CS_HIGH));
-		}
 
 		asd->npcs_pin = npcs_pin;
 		spi->controller_state = asd;
@@ -1307,7 +1240,7 @@ static int atmel_spi_one_transfer(struct spi_master *master,
 	 * better fault reporting.
 	 */
 	if ((!msg->is_dma_mapped)
-		&& (atmel_spi_use_dma(as, xfer)	|| as->use_pdc)) {
+		&& as->use_pdc) {
 		if (atmel_spi_dma_map_xfer(as, xfer) < 0)
 			return -ENOMEM;
 	}
@@ -1380,11 +1313,11 @@ static int atmel_spi_one_transfer(struct spi_master *master,
 			spi_readl(as, SR);
 
 		} else if (atmel_spi_use_dma(as, xfer)) {
-			atmel_spi_stop_dma(as);
+			atmel_spi_stop_dma(master);
 		}
 
 		if (!msg->is_dma_mapped
-			&& (atmel_spi_use_dma(as, xfer) || as->use_pdc))
+			&& as->use_pdc)
 			atmel_spi_dma_unmap_xfer(master, xfer);
 
 		return 0;
@@ -1395,7 +1328,7 @@ static int atmel_spi_one_transfer(struct spi_master *master,
 	}
 
 	if (!msg->is_dma_mapped
-		&& (atmel_spi_use_dma(as, xfer) || as->use_pdc))
+		&& as->use_pdc)
 		atmel_spi_dma_unmap_xfer(master, xfer);
 
 	if (xfer->delay_usecs)
@@ -1471,13 +1404,11 @@ static int atmel_spi_transfer_one_message(struct spi_master *master,
 static void atmel_spi_cleanup(struct spi_device *spi)
 {
 	struct atmel_spi_device	*asd = spi->controller_state;
-	unsigned		gpio = (unsigned long) spi->controller_data;
 
 	if (!asd)
 		return;
 
 	spi->controller_state = NULL;
-	gpio_free(gpio);
 	kfree(asd);
 }
 
@@ -1499,6 +1430,39 @@ static void atmel_get_caps(struct atmel_spi *as)
 }
 
 /*-------------------------------------------------------------------------*/
+static int atmel_spi_gpio_cs(struct platform_device *pdev)
+{
+	struct spi_master	*master = platform_get_drvdata(pdev);
+	struct atmel_spi	*as = spi_master_get_devdata(master);
+	struct device_node	*np = master->dev.of_node;
+	int			i;
+	int			ret = 0;
+	int			nb = 0;
+
+	if (!as->use_cs_gpios)
+		return 0;
+
+	if (!np)
+		return 0;
+
+	nb = of_gpio_named_count(np, "cs-gpios");
+	for (i = 0; i < nb; i++) {
+		int cs_gpio = of_get_named_gpio(pdev->dev.of_node,
+						"cs-gpios", i);
+
+		if (cs_gpio == -EPROBE_DEFER)
+			return cs_gpio;
+
+		if (gpio_is_valid(cs_gpio)) {
+			ret = devm_gpio_request(&pdev->dev, cs_gpio,
+						dev_name(&pdev->dev));
+			if (ret)
+				return ret;
+		}
+	}
+
+	return 0;
+}
 
 static int atmel_spi_probe(struct platform_device *pdev)
 {
@@ -1537,29 +1501,23 @@ static int atmel_spi_probe(struct platform_device *pdev)
 	master->bus_num = pdev->id;
 	master->num_chipselect = master->dev.of_node ? 0 : 4;
 	master->setup = atmel_spi_setup;
+	master->flags = (SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX);
 	master->transfer_one_message = atmel_spi_transfer_one_message;
 	master->cleanup = atmel_spi_cleanup;
 	master->auto_runtime_pm = true;
+	master->max_dma_len = SPI_MAX_DMA_XFER;
+	master->can_dma = atmel_spi_can_dma;
 	platform_set_drvdata(pdev, master);
 
 	as = spi_master_get_devdata(master);
 
-	/*
-	 * Scratch buffer is used for throwaway rx and tx data.
-	 * It's coherent to minimize dcache pollution.
-	 */
-	as->buffer = dma_alloc_coherent(&pdev->dev, BUFFER_SIZE,
-					&as->buffer_dma, GFP_KERNEL);
-	if (!as->buffer)
-		goto out_free;
-
 	spin_lock_init(&as->lock);
 
 	as->pdev = pdev;
 	as->regs = devm_ioremap_resource(&pdev->dev, regs);
 	if (IS_ERR(as->regs)) {
 		ret = PTR_ERR(as->regs);
-		goto out_free_buffer;
+		goto out_unmap_regs;
 	}
 	as->phybase = regs->start;
 	as->irq = irq;
@@ -1577,14 +1535,19 @@ static int atmel_spi_probe(struct platform_device *pdev)
 		master->num_chipselect = 4;
 	}
 
+	ret = atmel_spi_gpio_cs(pdev);
+	if (ret)
+		goto out_unmap_regs;
+
 	as->use_dma = false;
 	as->use_pdc = false;
 	if (as->caps.has_dma_support) {
-		ret = atmel_spi_configure_dma(as);
-		if (ret == 0)
+		ret = atmel_spi_configure_dma(master, as);
+		if (ret == 0) {
 			as->use_dma = true;
-		else if (ret == -EPROBE_DEFER)
+		} else if (ret == -EPROBE_DEFER) {
 			return ret;
+		}
 	} else {
 		as->use_pdc = true;
 	}
@@ -1606,6 +1569,9 @@ static int atmel_spi_probe(struct platform_device *pdev)
 	ret = clk_prepare_enable(clk);
 	if (ret)
 		goto out_free_irq;
+
+	as->spi_clk = clk_get_rate(clk);
+
 	spi_writel(as, CR, SPI_BIT(SWRST));
 	spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */
 	if (as->caps.has_wdrbt) {
@@ -1626,10 +1592,6 @@ static int atmel_spi_probe(struct platform_device *pdev)
 		spi_writel(as, CR, SPI_BIT(FIFOEN));
 	}
 
-	/* go! */
-	dev_info(&pdev->dev, "Atmel SPI Controller at 0x%08lx (irq %d)\n",
-			(unsigned long)regs->start, irq);
-
 	pm_runtime_set_autosuspend_delay(&pdev->dev, AUTOSUSPEND_TIMEOUT);
 	pm_runtime_use_autosuspend(&pdev->dev);
 	pm_runtime_set_active(&pdev->dev);
@@ -1639,6 +1601,10 @@ static int atmel_spi_probe(struct platform_device *pdev)
 	if (ret)
 		goto out_free_dma;
 
+	/* go! */
+	dev_info(&pdev->dev, "Atmel SPI Controller at 0x%08lx (irq %d)\n",
+			(unsigned long)regs->start, irq);
+
 	return 0;
 
 out_free_dma:
@@ -1646,16 +1612,13 @@ static int atmel_spi_probe(struct platform_device *pdev)
 	pm_runtime_set_suspended(&pdev->dev);
 
 	if (as->use_dma)
-		atmel_spi_release_dma(as);
+		atmel_spi_release_dma(master);
 
 	spi_writel(as, CR, SPI_BIT(SWRST));
 	spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */
 	clk_disable_unprepare(clk);
 out_free_irq:
 out_unmap_regs:
-out_free_buffer:
-	dma_free_coherent(&pdev->dev, BUFFER_SIZE, as->buffer,
-			as->buffer_dma);
 out_free:
 	spi_master_put(master);
 	return ret;
@@ -1671,8 +1634,8 @@ static int atmel_spi_remove(struct platform_device *pdev)
 	/* reset the hardware and block queue progress */
 	spin_lock_irq(&as->lock);
 	if (as->use_dma) {
-		atmel_spi_stop_dma(as);
-		atmel_spi_release_dma(as);
+		atmel_spi_stop_dma(master);
+		atmel_spi_release_dma(master);
 	}
 
 	spi_writel(as, CR, SPI_BIT(SWRST));
@@ -1680,9 +1643,6 @@ static int atmel_spi_remove(struct platform_device *pdev)
 	spi_readl(as, SR);
 	spin_unlock_irq(&as->lock);
 
-	dma_free_coherent(&pdev->dev, BUFFER_SIZE, as->buffer,
-			as->buffer_dma);
-
 	clk_disable_unprepare(as->clk);
 
 	pm_runtime_put_noidle(&pdev->dev);

drivers/spi/spi-axi-spi-engine.c

@@ -574,6 +574,7 @@ static const struct of_device_id spi_engine_match_table[] = {
 	{ .compatible = "adi,axi-spi-engine-1.00.a" },
 	{ },
 };
+MODULE_DEVICE_TABLE(of, spi_engine_match_table);
 
 static struct platform_driver spi_engine_driver = {
 	.probe = spi_engine_probe,

drivers/spi/spi-dw.c

@@ -502,6 +502,7 @@ int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
 	master->handle_err = dw_spi_handle_err;
 	master->max_speed_hz = dws->max_freq;
 	master->dev.of_node = dev->of_node;
+	master->flags = SPI_MASTER_GPIO_SS;
 
 	/* Basic HW init */
 	spi_hw_init(dev, dws);

drivers/spi/spi-fsl-dspi.c

@@ -15,6 +15,8 @@
 
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
 #include <linux/err.h>
 #include <linux/errno.h>
 #include <linux/interrupt.h>
@@ -40,6 +42,7 @@
 #define TRAN_STATE_WORD_ODD_NUM	0x04
 
 #define DSPI_FIFO_SIZE			4
+#define DSPI_DMA_BUFSIZE		(DSPI_FIFO_SIZE * 1024)
 
 #define SPI_MCR		0x00
 #define SPI_MCR_MASTER		(1 << 31)
@@ -72,6 +75,11 @@
 #define SPI_SR_TCFQF		0x80000000
 #define SPI_SR_CLEAR		0xdaad0000
 
+#define SPI_RSER_TFFFE		BIT(25)
+#define SPI_RSER_TFFFD		BIT(24)
+#define SPI_RSER_RFDFE		BIT(17)
+#define SPI_RSER_RFDFD		BIT(16)
+
 #define SPI_RSER		0x30
 #define SPI_RSER_EOQFE		0x10000000
 #define SPI_RSER_TCFQE		0x80000000
@@ -109,6 +117,8 @@
 
 #define SPI_TCR_TCNT_MAX	0x10000
 
+#define DMA_COMPLETION_TIMEOUT	msecs_to_jiffies(3000)
+
 struct chip_data {
 	u32 mcr_val;
 	u32 ctar_val;
@@ -118,6 +128,7 @@ struct chip_data {
 enum dspi_trans_mode {
 	DSPI_EOQ_MODE = 0,
 	DSPI_TCFQ_MODE,
+	DSPI_DMA_MODE,
 };
 
 struct fsl_dspi_devtype_data {
@@ -126,7 +137,7 @@ struct fsl_dspi_devtype_data {
 };
 
 static const struct fsl_dspi_devtype_data vf610_data = {
-	.trans_mode = DSPI_EOQ_MODE,
+	.trans_mode = DSPI_DMA_MODE,
 	.max_clock_factor = 2,
 };
 
@@ -140,6 +151,23 @@ static const struct fsl_dspi_devtype_data ls2085a_data = {
 	.max_clock_factor = 8,
 };
 
+struct fsl_dspi_dma {
+	/* Length of transfer in words of DSPI_FIFO_SIZE */
+	u32 curr_xfer_len;
+
+	u32 *tx_dma_buf;
+	struct dma_chan *chan_tx;
+	dma_addr_t tx_dma_phys;
+	struct completion cmd_tx_complete;
+	struct dma_async_tx_descriptor *tx_desc;
+
+	u32 *rx_dma_buf;
+	struct dma_chan *chan_rx;
+	dma_addr_t rx_dma_phys;
+	struct completion cmd_rx_complete;
+	struct dma_async_tx_descriptor *rx_desc;
+};
+
 struct fsl_dspi {
 	struct spi_master	*master;
 	struct platform_device	*pdev;
@@ -166,8 +194,11 @@ struct fsl_dspi {
 	u32			waitflags;
 
 	u32			spi_tcnt;
+	struct fsl_dspi_dma	*dma;
 };
 
+static u32 dspi_data_to_pushr(struct fsl_dspi *dspi, int tx_word);
+
 static inline int is_double_byte_mode(struct fsl_dspi *dspi)
 {
 	unsigned int val;
@@ -177,6 +208,255 @@ static inline int is_double_byte_mode(struct fsl_dspi *dspi)
 	return ((val & SPI_FRAME_BITS_MASK) == SPI_FRAME_BITS(8)) ? 0 : 1;
 }
 
+static void dspi_tx_dma_callback(void *arg)
+{
+	struct fsl_dspi *dspi = arg;
+	struct fsl_dspi_dma *dma = dspi->dma;
+
+	complete(&dma->cmd_tx_complete);
+}
+
+static void dspi_rx_dma_callback(void *arg)
+{
+	struct fsl_dspi *dspi = arg;
+	struct fsl_dspi_dma *dma = dspi->dma;
+	int rx_word;
+	int i;
+	u16 d;
+
+	rx_word = is_double_byte_mode(dspi);
+
+	if (!(dspi->dataflags & TRAN_STATE_RX_VOID)) {
+		for (i = 0; i < dma->curr_xfer_len; i++) {
+			d = dspi->dma->rx_dma_buf[i];
+			rx_word ? (*(u16 *)dspi->rx = d) :
+						(*(u8 *)dspi->rx = d);
+			dspi->rx += rx_word + 1;
+		}
+	}
+
+	complete(&dma->cmd_rx_complete);
+}
+
+static int dspi_next_xfer_dma_submit(struct fsl_dspi *dspi)
+{
+	struct fsl_dspi_dma *dma = dspi->dma;
+	struct device *dev = &dspi->pdev->dev;
+	int time_left;
+	int tx_word;
+	int i;
+
+	tx_word = is_double_byte_mode(dspi);
+
+	for (i = 0; i < dma->curr_xfer_len; i++) {
+		dspi->dma->tx_dma_buf[i] = dspi_data_to_pushr(dspi, tx_word);
+		if ((dspi->cs_change) && (!dspi->len))
+			dspi->dma->tx_dma_buf[i] &= ~SPI_PUSHR_CONT;
+	}
+
+	dma->tx_desc = dmaengine_prep_slave_single(dma->chan_tx,
+					dma->tx_dma_phys,
+					dma->curr_xfer_len *
+					DMA_SLAVE_BUSWIDTH_4_BYTES,
+					DMA_MEM_TO_DEV,
+					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+	if (!dma->tx_desc) {
+		dev_err(dev, "Not able to get desc for DMA xfer\n");
+		return -EIO;
+	}
+
+	dma->tx_desc->callback = dspi_tx_dma_callback;
+	dma->tx_desc->callback_param = dspi;
+	if (dma_submit_error(dmaengine_submit(dma->tx_desc))) {
+		dev_err(dev, "DMA submit failed\n");
+		return -EINVAL;
+	}
+
+	dma->rx_desc = dmaengine_prep_slave_single(dma->chan_rx,
+					dma->rx_dma_phys,
+					dma->curr_xfer_len *
+					DMA_SLAVE_BUSWIDTH_4_BYTES,
+					DMA_DEV_TO_MEM,
+					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+	if (!dma->rx_desc) {
+		dev_err(dev, "Not able to get desc for DMA xfer\n");
+		return -EIO;
+	}
+
+	dma->rx_desc->callback = dspi_rx_dma_callback;
+	dma->rx_desc->callback_param = dspi;
+	if (dma_submit_error(dmaengine_submit(dma->rx_desc))) {
+		dev_err(dev, "DMA submit failed\n");
+		return -EINVAL;
+	}
+
+	reinit_completion(&dspi->dma->cmd_rx_complete);
+	reinit_completion(&dspi->dma->cmd_tx_complete);
+
+	dma_async_issue_pending(dma->chan_rx);
+	dma_async_issue_pending(dma->chan_tx);
+
+	time_left = wait_for_completion_timeout(&dspi->dma->cmd_tx_complete,
+					DMA_COMPLETION_TIMEOUT);
+	if (time_left == 0) {
+		dev_err(dev, "DMA tx timeout\n");
+		dmaengine_terminate_all(dma->chan_tx);
+		dmaengine_terminate_all(dma->chan_rx);
+		return -ETIMEDOUT;
+	}
+
+	time_left = wait_for_completion_timeout(&dspi->dma->cmd_rx_complete,
+					DMA_COMPLETION_TIMEOUT);
+	if (time_left == 0) {
+		dev_err(dev, "DMA rx timeout\n");
+		dmaengine_terminate_all(dma->chan_tx);
+		dmaengine_terminate_all(dma->chan_rx);
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static int dspi_dma_xfer(struct fsl_dspi *dspi)
+{
+	struct fsl_dspi_dma *dma = dspi->dma;
+	struct device *dev = &dspi->pdev->dev;
+	int curr_remaining_bytes;
+	int bytes_per_buffer;
+	int word = 1;
+	int ret = 0;
+
+	if (is_double_byte_mode(dspi))
+		word = 2;
+	curr_remaining_bytes = dspi->len;
+	bytes_per_buffer = DSPI_DMA_BUFSIZE / DSPI_FIFO_SIZE;
+	while (curr_remaining_bytes) {
+		/* Check if current transfer fits the DMA buffer */
+		dma->curr_xfer_len = curr_remaining_bytes / word;
+		if (dma->curr_xfer_len > bytes_per_buffer)
+			dma->curr_xfer_len = bytes_per_buffer;
+
+		ret = dspi_next_xfer_dma_submit(dspi);
+		if (ret) {
+			dev_err(dev, "DMA transfer failed\n");
+			goto exit;
+
+		} else {
+			curr_remaining_bytes -= dma->curr_xfer_len * word;
+			if (curr_remaining_bytes < 0)
+				curr_remaining_bytes = 0;
+		}
+	}
+
+exit:
+	return ret;
+}
+
+static int dspi_request_dma(struct fsl_dspi *dspi, phys_addr_t phy_addr)
+{
+	struct fsl_dspi_dma *dma;
+	struct dma_slave_config cfg;
+	struct device *dev = &dspi->pdev->dev;
+	int ret;
+
+	dma = devm_kzalloc(dev, sizeof(*dma), GFP_KERNEL);
+	if (!dma)
+		return -ENOMEM;
+
+	dma->chan_rx = dma_request_slave_channel(dev, "rx");
+	if (!dma->chan_rx) {
+		dev_err(dev, "rx dma channel not available\n");
+		ret = -ENODEV;
+		return ret;
+	}
+
+	dma->chan_tx = dma_request_slave_channel(dev, "tx");
+	if (!dma->chan_tx) {
+		dev_err(dev, "tx dma channel not available\n");
+		ret = -ENODEV;
+		goto err_tx_channel;
+	}
+
+	dma->tx_dma_buf = dma_alloc_coherent(dev, DSPI_DMA_BUFSIZE,
+					&dma->tx_dma_phys, GFP_KERNEL);
+	if (!dma->tx_dma_buf) {
+		ret = -ENOMEM;
+		goto err_tx_dma_buf;
+	}
+
+	dma->rx_dma_buf = dma_alloc_coherent(dev, DSPI_DMA_BUFSIZE,
+					&dma->rx_dma_phys, GFP_KERNEL);
+	if (!dma->rx_dma_buf) {
+		ret = -ENOMEM;
+		goto err_rx_dma_buf;
+	}
+
+	cfg.src_addr = phy_addr + SPI_POPR;
+	cfg.dst_addr = phy_addr + SPI_PUSHR;
+	cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+	cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+	cfg.src_maxburst = 1;
+	cfg.dst_maxburst = 1;
+
+	cfg.direction = DMA_DEV_TO_MEM;
+	ret = dmaengine_slave_config(dma->chan_rx, &cfg);
+	if (ret) {
+		dev_err(dev, "can't configure rx dma channel\n");
+		ret = -EINVAL;
+		goto err_slave_config;
+	}
+
+	cfg.direction = DMA_MEM_TO_DEV;
+	ret = dmaengine_slave_config(dma->chan_tx, &cfg);
+	if (ret) {
+		dev_err(dev, "can't configure tx dma channel\n");
+		ret = -EINVAL;
+		goto err_slave_config;
+	}
+
+	dspi->dma = dma;
+	init_completion(&dma->cmd_tx_complete);
+	init_completion(&dma->cmd_rx_complete);
+
+	return 0;
+
+err_slave_config:
+	dma_free_coherent(dev, DSPI_DMA_BUFSIZE,
+			dma->rx_dma_buf, dma->rx_dma_phys);
+err_rx_dma_buf:
+	dma_free_coherent(dev, DSPI_DMA_BUFSIZE,
+			dma->tx_dma_buf, dma->tx_dma_phys);
+err_tx_dma_buf:
+	dma_release_channel(dma->chan_tx);
+err_tx_channel:
+	dma_release_channel(dma->chan_rx);
+
+	devm_kfree(dev, dma);
+	dspi->dma = NULL;
+
+	return ret;
+}
+
+static void dspi_release_dma(struct fsl_dspi *dspi)
+{
+	struct fsl_dspi_dma *dma = dspi->dma;
+	struct device *dev = &dspi->pdev->dev;
+
+	if (dma) {
+		if (dma->chan_tx) {
+			dma_unmap_single(dev, dma->tx_dma_phys,
+					DSPI_DMA_BUFSIZE, DMA_TO_DEVICE);
+			dma_release_channel(dma->chan_tx);
+		}
+
+		if (dma->chan_rx) {
+			dma_unmap_single(dev, dma->rx_dma_phys,
+					DSPI_DMA_BUFSIZE, DMA_FROM_DEVICE);
+			dma_release_channel(dma->chan_rx);
+		}
+	}
+}
+
 static void hz_to_spi_baud(char *pbr, char *br, int speed_hz,
 		unsigned long clkrate)
 {
@@ -425,6 +705,12 @@ static int dspi_transfer_one_message(struct spi_master *master,
 			regmap_write(dspi->regmap, SPI_RSER, SPI_RSER_TCFQE);
 			dspi_tcfq_write(dspi);
 			break;
+		case DSPI_DMA_MODE:
+			regmap_write(dspi->regmap, SPI_RSER,
+				SPI_RSER_TFFFE | SPI_RSER_TFFFD |
+				SPI_RSER_RFDFE | SPI_RSER_RFDFD);
+			status = dspi_dma_xfer(dspi);
+			break;
 		default:
 			dev_err(&dspi->pdev->dev, "unsupported trans_mode %u\n",
 				trans_mode);
@@ -432,9 +718,13 @@ static int dspi_transfer_one_message(struct spi_master *master,
 			goto out;
 		}
 
-		if (wait_event_interruptible(dspi->waitq, dspi->waitflags))
-			dev_err(&dspi->pdev->dev, "wait transfer complete fail!\n");
-		dspi->waitflags = 0;
+		if (trans_mode != DSPI_DMA_MODE) {
+			if (wait_event_interruptible(dspi->waitq,
+						dspi->waitflags))
+				dev_err(&dspi->pdev->dev,
+					"wait transfer complete fail!\n");
+			dspi->waitflags = 0;
+		}
 
 		if (transfer->delay_usecs)
 			udelay(transfer->delay_usecs);
@@ -740,6 +1030,13 @@ static int dspi_probe(struct platform_device *pdev)
 	if (ret)
 		goto out_master_put;
 
+	if (dspi->devtype_data->trans_mode == DSPI_DMA_MODE) {
+		if (dspi_request_dma(dspi, res->start)) {
+			dev_err(&pdev->dev, "can't get dma channels\n");
+			goto out_clk_put;
+		}
+	}
+
 	master->max_speed_hz =
 		clk_get_rate(dspi->clk) / dspi->devtype_data->max_clock_factor;
 
@@ -768,6 +1065,7 @@ static int dspi_remove(struct platform_device *pdev)
 	struct fsl_dspi *dspi = spi_master_get_devdata(master);
 
 	/* Disconnect from the SPI framework */
+	dspi_release_dma(dspi);
 	clk_disable_unprepare(dspi->clk);
 	spi_unregister_master(dspi->master);
 

drivers/spi/spi-fsl-lib.h

@@ -28,10 +28,6 @@ struct mpc8xxx_spi {
 	/* rx & tx bufs from the spi_transfer */
 	const void *tx;
 	void *rx;
-#if IS_ENABLED(CONFIG_SPI_FSL_ESPI)
-	int len;
-	u8 *local_buf;
-#endif
 
 	int subblock;
 	struct spi_pram __iomem *pram;

drivers/spi/spi-fsl-lpspi.c

+/*
+ * Freescale i.MX7ULP LPSPI driver
+ *
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
+#include <linux/types.h>
+
+#define DRIVER_NAME "fsl_lpspi"
+
+/* i.MX7ULP LPSPI registers */
+#define IMX7ULP_VERID	0x0
+#define IMX7ULP_PARAM	0x4
+#define IMX7ULP_CR	0x10
+#define IMX7ULP_SR	0x14
+#define IMX7ULP_IER	0x18
+#define IMX7ULP_DER	0x1c
+#define IMX7ULP_CFGR0	0x20
+#define IMX7ULP_CFGR1	0x24
+#define IMX7ULP_DMR0	0x30
+#define IMX7ULP_DMR1	0x34
+#define IMX7ULP_CCR	0x40
+#define IMX7ULP_FCR	0x58
+#define IMX7ULP_FSR	0x5c
+#define IMX7ULP_TCR	0x60
+#define IMX7ULP_TDR	0x64
+#define IMX7ULP_RSR	0x70
+#define IMX7ULP_RDR	0x74
+
+/* General control register field define */
+#define CR_RRF		BIT(9)
+#define CR_RTF		BIT(8)
+#define CR_RST		BIT(1)
+#define CR_MEN		BIT(0)
+#define SR_TCF		BIT(10)
+#define SR_RDF		BIT(1)
+#define SR_TDF		BIT(0)
+#define IER_TCIE	BIT(10)
+#define IER_RDIE	BIT(1)
+#define IER_TDIE	BIT(0)
+#define CFGR1_PCSCFG	BIT(27)
+#define CFGR1_PCSPOL	BIT(8)
+#define CFGR1_NOSTALL	BIT(3)
+#define CFGR1_MASTER	BIT(0)
+#define RSR_RXEMPTY	BIT(1)
+#define TCR_CPOL	BIT(31)
+#define TCR_CPHA	BIT(30)
+#define TCR_CONT	BIT(21)
+#define TCR_CONTC	BIT(20)
+#define TCR_RXMSK	BIT(19)
+#define TCR_TXMSK	BIT(18)
+
+static int clkdivs[] = {1, 2, 4, 8, 16, 32, 64, 128};
+
+struct lpspi_config {
+	u8 bpw;
+	u8 chip_select;
+	u8 prescale;
+	u16 mode;
+	u32 speed_hz;
+};
+
+struct fsl_lpspi_data {
+	struct device *dev;
+	void __iomem *base;
+	struct clk *clk;
+
+	void *rx_buf;
+	const void *tx_buf;
+	void (*tx)(struct fsl_lpspi_data *);
+	void (*rx)(struct fsl_lpspi_data *);
+
+	u32 remain;
+	u8 txfifosize;
+	u8 rxfifosize;
+
+	struct lpspi_config config;
+	struct completion xfer_done;
+};
+
+static const struct of_device_id fsl_lpspi_dt_ids[] = {
+	{ .compatible = "fsl,imx7ulp-spi", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, fsl_lpspi_dt_ids);
+
+#define LPSPI_BUF_RX(type)						\
+static void fsl_lpspi_buf_rx_##type(struct fsl_lpspi_data *fsl_lpspi)	\
+{									\
+	unsigned int val = readl(fsl_lpspi->base + IMX7ULP_RDR);	\
+									\
+	if (fsl_lpspi->rx_buf) {					\
+		*(type *)fsl_lpspi->rx_buf = val;			\
+		fsl_lpspi->rx_buf += sizeof(type);                      \
+	}								\
+}
+
+#define LPSPI_BUF_TX(type)						\
+static void fsl_lpspi_buf_tx_##type(struct fsl_lpspi_data *fsl_lpspi)	\
+{									\
+	type val = 0;							\
+									\
+	if (fsl_lpspi->tx_buf) {					\
+		val = *(type *)fsl_lpspi->tx_buf;			\
+		fsl_lpspi->tx_buf += sizeof(type);			\
+	}								\
+									\
+	fsl_lpspi->remain -= sizeof(type);				\
+	writel(val, fsl_lpspi->base + IMX7ULP_TDR);			\
+}
+
+LPSPI_BUF_RX(u8)
+LPSPI_BUF_TX(u8)
+LPSPI_BUF_RX(u16)
+LPSPI_BUF_TX(u16)
+LPSPI_BUF_RX(u32)
+LPSPI_BUF_TX(u32)
+
+static void fsl_lpspi_intctrl(struct fsl_lpspi_data *fsl_lpspi,
+			      unsigned int enable)
+{
+	writel(enable, fsl_lpspi->base + IMX7ULP_IER);
+}
+
+static int lpspi_prepare_xfer_hardware(struct spi_master *master)
+{
+	struct fsl_lpspi_data *fsl_lpspi = spi_master_get_devdata(master);
+
+	return clk_prepare_enable(fsl_lpspi->clk);
+}
+
+static int lpspi_unprepare_xfer_hardware(struct spi_master *master)
+{
+	struct fsl_lpspi_data *fsl_lpspi = spi_master_get_devdata(master);
+
+	clk_disable_unprepare(fsl_lpspi->clk);
+
+	return 0;
+}
+
+static int fsl_lpspi_txfifo_empty(struct fsl_lpspi_data *fsl_lpspi)
+{
+	u32 txcnt;
+	unsigned long orig_jiffies = jiffies;
+
+	do {
+		txcnt = readl(fsl_lpspi->base + IMX7ULP_FSR) & 0xff;
+
+		if (time_after(jiffies, orig_jiffies + msecs_to_jiffies(500))) {
+			dev_dbg(fsl_lpspi->dev, "txfifo empty timeout\n");
+			return -ETIMEDOUT;
+		}
+		cond_resched();
+
+	} while (txcnt);
+
+	return 0;
+}
+
+static void fsl_lpspi_write_tx_fifo(struct fsl_lpspi_data *fsl_lpspi)
+{
+	u8 txfifo_cnt;
+
+	txfifo_cnt = readl(fsl_lpspi->base + IMX7ULP_FSR) & 0xff;
+
+	while (txfifo_cnt < fsl_lpspi->txfifosize) {
+		if (!fsl_lpspi->remain)
+			break;
+		fsl_lpspi->tx(fsl_lpspi);
+		txfifo_cnt++;
+	}
+
+	if (!fsl_lpspi->remain && (txfifo_cnt < fsl_lpspi->txfifosize))
+		writel(0, fsl_lpspi->base + IMX7ULP_TDR);
+	else
+		fsl_lpspi_intctrl(fsl_lpspi, IER_TDIE);
+}
+
+static void fsl_lpspi_read_rx_fifo(struct fsl_lpspi_data *fsl_lpspi)
+{
+	while (!(readl(fsl_lpspi->base + IMX7ULP_RSR) & RSR_RXEMPTY))
+		fsl_lpspi->rx(fsl_lpspi);
+}
+
+static void fsl_lpspi_set_cmd(struct fsl_lpspi_data *fsl_lpspi,
+			      bool is_first_xfer)
+{
+	u32 temp = 0;
+
+	temp |= fsl_lpspi->config.bpw - 1;
+	temp |= fsl_lpspi->config.prescale << 27;
+	temp |= (fsl_lpspi->config.mode & 0x3) << 30;
+	temp |= (fsl_lpspi->config.chip_select & 0x3) << 24;
+
+	/*
+	 * Set TCR_CONT will keep SS asserted after current transfer.
+	 * For the first transfer, clear TCR_CONTC to assert SS.
+	 * For subsequent transfer, set TCR_CONTC to keep SS asserted.
+	 */
+	temp |= TCR_CONT;
+	if (is_first_xfer)
+		temp &= ~TCR_CONTC;
+	else
+		temp |= TCR_CONTC;
+
+	writel(temp, fsl_lpspi->base + IMX7ULP_TCR);
+
+	dev_dbg(fsl_lpspi->dev, "TCR=0x%x\n", temp);
+}
+
+static void fsl_lpspi_set_watermark(struct fsl_lpspi_data *fsl_lpspi)
+{
+	u32 temp;
+
+	temp = fsl_lpspi->txfifosize >> 1 | (fsl_lpspi->rxfifosize >> 1) << 16;
+
+	writel(temp, fsl_lpspi->base + IMX7ULP_FCR);
+
+	dev_dbg(fsl_lpspi->dev, "FCR=0x%x\n", temp);
+}
+
+static int fsl_lpspi_set_bitrate(struct fsl_lpspi_data *fsl_lpspi)
+{
+	struct lpspi_config config = fsl_lpspi->config;
+	unsigned int perclk_rate, scldiv;
+	u8 prescale;
+
+	perclk_rate = clk_get_rate(fsl_lpspi->clk);
+	for (prescale = 0; prescale < 8; prescale++) {
+		scldiv = perclk_rate /
+			 (clkdivs[prescale] * config.speed_hz) - 2;
+		if (scldiv < 256) {
+			fsl_lpspi->config.prescale = prescale;
+			break;
+		}
+	}
+
+	if (prescale == 8 && scldiv >= 256)
+		return -EINVAL;
+
+	writel(scldiv, fsl_lpspi->base + IMX7ULP_CCR);
+
+	dev_dbg(fsl_lpspi->dev, "perclk=%d, speed=%d, prescale =%d, scldiv=%d\n",
+		perclk_rate, config.speed_hz, prescale, scldiv);
+
+	return 0;
+}
+
+static int fsl_lpspi_config(struct fsl_lpspi_data *fsl_lpspi)
+{
+	u32 temp;
+	int ret;
+
+	temp = CR_RST;
+	writel(temp, fsl_lpspi->base + IMX7ULP_CR);
+	writel(0, fsl_lpspi->base + IMX7ULP_CR);
+
+	ret = fsl_lpspi_set_bitrate(fsl_lpspi);
+	if (ret)
+		return ret;
+
+	fsl_lpspi_set_watermark(fsl_lpspi);
+
+	temp = CFGR1_PCSCFG | CFGR1_MASTER | CFGR1_NOSTALL;
+	if (fsl_lpspi->config.mode & SPI_CS_HIGH)
+		temp |= CFGR1_PCSPOL;
+	writel(temp, fsl_lpspi->base + IMX7ULP_CFGR1);
+
+	temp = readl(fsl_lpspi->base + IMX7ULP_CR);
+	temp |= CR_RRF | CR_RTF | CR_MEN;
+	writel(temp, fsl_lpspi->base + IMX7ULP_CR);
+
+	return 0;
+}
+
+static void fsl_lpspi_setup_transfer(struct spi_device *spi,
+				     struct spi_transfer *t)
+{
+	struct fsl_lpspi_data *fsl_lpspi = spi_master_get_devdata(spi->master);
+
+	fsl_lpspi->config.mode = spi->mode;
+	fsl_lpspi->config.bpw = t ? t->bits_per_word : spi->bits_per_word;
+	fsl_lpspi->config.speed_hz = t ? t->speed_hz : spi->max_speed_hz;
+	fsl_lpspi->config.chip_select = spi->chip_select;
+
+	if (!fsl_lpspi->config.speed_hz)
+		fsl_lpspi->config.speed_hz = spi->max_speed_hz;
+	if (!fsl_lpspi->config.bpw)
+		fsl_lpspi->config.bpw = spi->bits_per_word;
+
+	/* Initialize the functions for transfer */
+	if (fsl_lpspi->config.bpw <= 8) {
+		fsl_lpspi->rx = fsl_lpspi_buf_rx_u8;
+		fsl_lpspi->tx = fsl_lpspi_buf_tx_u8;
+	} else if (fsl_lpspi->config.bpw <= 16) {
+		fsl_lpspi->rx = fsl_lpspi_buf_rx_u16;
+		fsl_lpspi->tx = fsl_lpspi_buf_tx_u16;
+	} else {
+		fsl_lpspi->rx = fsl_lpspi_buf_rx_u32;
+		fsl_lpspi->tx = fsl_lpspi_buf_tx_u32;
+	}
+
+	fsl_lpspi_config(fsl_lpspi);
+}
+
+static int fsl_lpspi_transfer_one(struct spi_master *master,
+				  struct spi_device *spi,
+				  struct spi_transfer *t)
+{
+	struct fsl_lpspi_data *fsl_lpspi = spi_master_get_devdata(master);
+	int ret;
+
+	fsl_lpspi->tx_buf = t->tx_buf;
+	fsl_lpspi->rx_buf = t->rx_buf;
+	fsl_lpspi->remain = t->len;
+
+	reinit_completion(&fsl_lpspi->xfer_done);
+	fsl_lpspi_write_tx_fifo(fsl_lpspi);
+
+	ret = wait_for_completion_timeout(&fsl_lpspi->xfer_done, HZ);
+	if (!ret) {
+		dev_dbg(fsl_lpspi->dev, "wait for completion timeout\n");
+		return -ETIMEDOUT;
+	}
+
+	ret = fsl_lpspi_txfifo_empty(fsl_lpspi);
+	if (ret)
+		return ret;
+
+	fsl_lpspi_read_rx_fifo(fsl_lpspi);
+
+	return 0;
+}
+
+static int fsl_lpspi_transfer_one_msg(struct spi_master *master,
+				      struct spi_message *msg)
+{
+	struct fsl_lpspi_data *fsl_lpspi = spi_master_get_devdata(master);
+	struct spi_device *spi = msg->spi;
+	struct spi_transfer *xfer;
+	bool is_first_xfer = true;
+	u32 temp;
+	int ret;
+
+	msg->status = 0;
+	msg->actual_length = 0;
+
+	list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+		fsl_lpspi_setup_transfer(spi, xfer);
+		fsl_lpspi_set_cmd(fsl_lpspi, is_first_xfer);
+
+		is_first_xfer = false;
+
+		ret = fsl_lpspi_transfer_one(master, spi, xfer);
+		if (ret < 0)
+			goto complete;
+
+		msg->actual_length += xfer->len;
+	}
+
+complete:
+	/* de-assert SS, then finalize current message */
+	temp = readl(fsl_lpspi->base + IMX7ULP_TCR);
+	temp &= ~TCR_CONTC;
+	writel(temp, fsl_lpspi->base + IMX7ULP_TCR);
+
+	msg->status = ret;
+	spi_finalize_current_message(master);
+
+	return ret;
+}
+
+static irqreturn_t fsl_lpspi_isr(int irq, void *dev_id)
+{
+	struct fsl_lpspi_data *fsl_lpspi = dev_id;
+	u32 temp;
+
+	fsl_lpspi_intctrl(fsl_lpspi, 0);
+	temp = readl(fsl_lpspi->base + IMX7ULP_SR);
+
+	fsl_lpspi_read_rx_fifo(fsl_lpspi);
+
+	if (temp & SR_TDF) {
+		fsl_lpspi_write_tx_fifo(fsl_lpspi);
+
+		if (!fsl_lpspi->remain)
+			complete(&fsl_lpspi->xfer_done);
+
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+static int fsl_lpspi_probe(struct platform_device *pdev)
+{
+	struct fsl_lpspi_data *fsl_lpspi;
+	struct spi_master *master;
+	struct resource *res;
+	int ret, irq;
+	u32 temp;
+
+	master = spi_alloc_master(&pdev->dev, sizeof(struct fsl_lpspi_data));
+	if (!master)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, master);
+
+	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32);
+	master->bus_num = pdev->id;
+
+	fsl_lpspi = spi_master_get_devdata(master);
+	fsl_lpspi->dev = &pdev->dev;
+
+	master->transfer_one_message = fsl_lpspi_transfer_one_msg;
+	master->prepare_transfer_hardware = lpspi_prepare_xfer_hardware;
+	master->unprepare_transfer_hardware = lpspi_unprepare_xfer_hardware;
+	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+	master->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
+	master->dev.of_node = pdev->dev.of_node;
+	master->bus_num = pdev->id;
+
+	init_completion(&fsl_lpspi->xfer_done);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	fsl_lpspi->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(fsl_lpspi->base)) {
+		ret = PTR_ERR(fsl_lpspi->base);
+		goto out_master_put;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		ret = irq;
+		goto out_master_put;
+	}
+
+	ret = devm_request_irq(&pdev->dev, irq, fsl_lpspi_isr, 0,
+			       dev_name(&pdev->dev), fsl_lpspi);
+	if (ret) {
+		dev_err(&pdev->dev, "can't get irq%d: %d\n", irq, ret);
+		goto out_master_put;
+	}
+
+	fsl_lpspi->clk = devm_clk_get(&pdev->dev, "ipg");
+	if (IS_ERR(fsl_lpspi->clk)) {
+		ret = PTR_ERR(fsl_lpspi->clk);
+		goto out_master_put;
+	}
+
+	ret = clk_prepare_enable(fsl_lpspi->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "can't enable lpspi clock, ret=%d\n", ret);
+		goto out_master_put;
+	}
+
+	temp = readl(fsl_lpspi->base + IMX7ULP_PARAM);
+	fsl_lpspi->txfifosize = 1 << (temp & 0x0f);
+	fsl_lpspi->rxfifosize = 1 << ((temp >> 8) & 0x0f);
+
+	clk_disable_unprepare(fsl_lpspi->clk);
+
+	ret = devm_spi_register_master(&pdev->dev, master);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "spi_register_master error.\n");
+		goto out_master_put;
+	}
+
+	return 0;
+
+out_master_put:
+	spi_master_put(master);
+
+	return ret;
+}
+
+static int fsl_lpspi_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct fsl_lpspi_data *fsl_lpspi = spi_master_get_devdata(master);
+
+	clk_disable_unprepare(fsl_lpspi->clk);
+
+	return 0;
+}
+
+static struct platform_driver fsl_lpspi_driver = {
+	.driver = {
+		   .name = DRIVER_NAME,
+		   .of_match_table = fsl_lpspi_dt_ids,
+		   },
+	.probe = fsl_lpspi_probe,
+	.remove = fsl_lpspi_remove,
+};
+module_platform_driver(fsl_lpspi_driver);
+
+MODULE_DESCRIPTION("LPSPI Master Controller driver");
+MODULE_AUTHOR("Gao Pan <pandy.gao@nxp.com>");
+MODULE_LICENSE("GPL");

drivers/spi/spi-imx.c

@@ -173,15 +173,16 @@ static int mxc_clkdivs[] = {0, 3, 4, 6, 8, 12, 16, 24, 32, 48, 64, 96, 128, 192,
 
 /* MX21, MX27 */
 static unsigned int spi_imx_clkdiv_1(unsigned int fin,
-		unsigned int fspi, unsigned int max)
+		unsigned int fspi, unsigned int max, unsigned int *fres)
 {
 	int i;
 
 	for (i = 2; i < max; i++)
 		if (fspi * mxc_clkdivs[i] >= fin)
-			return i;
+			break;
 
-	return max;
+	*fres = fin / mxc_clkdivs[i];
+	return i;
 }
 
 /* MX1, MX31, MX35, MX51 CSPI */
@@ -442,6 +443,7 @@ static void mx51_ecspi_reset(struct spi_imx_data *spi_imx)
 #define MX31_CSPICTRL_ENABLE	(1 << 0)
 #define MX31_CSPICTRL_MASTER	(1 << 1)
 #define MX31_CSPICTRL_XCH	(1 << 2)
+#define MX31_CSPICTRL_SMC	(1 << 3)
 #define MX31_CSPICTRL_POL	(1 << 4)
 #define MX31_CSPICTRL_PHA	(1 << 5)
 #define MX31_CSPICTRL_SSCTL	(1 << 6)
@@ -452,6 +454,10 @@ static void mx51_ecspi_reset(struct spi_imx_data *spi_imx)
 #define MX35_CSPICTRL_CS_SHIFT	12
 #define MX31_CSPICTRL_DR_SHIFT	16
 
+#define MX31_CSPI_DMAREG	0x10
+#define MX31_DMAREG_RH_DEN	(1<<4)
+#define MX31_DMAREG_TH_DEN	(1<<1)
+
 #define MX31_CSPISTATUS		0x14
 #define MX31_STATUS_RR		(1 << 3)
 
@@ -511,6 +517,9 @@ static int mx31_config(struct spi_device *spi, struct spi_imx_config *config)
 			(is_imx35_cspi(spi_imx) ? MX35_CSPICTRL_CS_SHIFT :
 						  MX31_CSPICTRL_CS_SHIFT);
 
+	if (spi_imx->usedma)
+		reg |= MX31_CSPICTRL_SMC;
+
 	writel(reg, spi_imx->base + MXC_CSPICTRL);
 
 	reg = readl(spi_imx->base + MX31_CSPI_TESTREG);
@@ -520,6 +529,13 @@ static int mx31_config(struct spi_device *spi, struct spi_imx_config *config)
 		reg &= ~MX31_TEST_LBC;
 	writel(reg, spi_imx->base + MX31_CSPI_TESTREG);
 
+	if (spi_imx->usedma) {
+		/* configure DMA requests when RXFIFO is half full and
+		   when TXFIFO is half empty */
+		writel(MX31_DMAREG_RH_DEN | MX31_DMAREG_TH_DEN,
+			spi_imx->base + MX31_CSPI_DMAREG);
+	}
+
 	return 0;
 }
 
@@ -574,9 +590,12 @@ static int mx21_config(struct spi_device *spi, struct spi_imx_config *config)
 	struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
 	unsigned int reg = MX21_CSPICTRL_ENABLE | MX21_CSPICTRL_MASTER;
 	unsigned int max = is_imx27_cspi(spi_imx) ? 16 : 18;
+	unsigned int clk;
+
+	reg |= spi_imx_clkdiv_1(spi_imx->spi_clk, config->speed_hz, max, &clk)
+		<< MX21_CSPICTRL_DR_SHIFT;
+	spi_imx->spi_bus_clk = clk;
 
-	reg |= spi_imx_clkdiv_1(spi_imx->spi_clk, config->speed_hz, max) <<
-		MX21_CSPICTRL_DR_SHIFT;
 	reg |= config->bpw - 1;
 
 	if (spi->mode & SPI_CPHA)
@@ -1244,10 +1263,10 @@ static int spi_imx_probe(struct platform_device *pdev)
 
 	spi_imx->spi_clk = clk_get_rate(spi_imx->clk_per);
 	/*
-	 * Only validated on i.mx6 now, can remove the constrain if validated on
-	 * other chips.
+	 * Only validated on i.mx35 and i.mx6 now, can remove the constraint
+	 * if validated on other chips.
 	 */
-	if (is_imx51_ecspi(spi_imx)) {
+	if (is_imx35_cspi(spi_imx) || is_imx51_ecspi(spi_imx)) {
 		ret = spi_imx_sdma_init(&pdev->dev, spi_imx, master);
 		if (ret == -EPROBE_DEFER)
 			goto out_clk_put;

drivers/spi/spi-jcore.c

@@ -214,6 +214,7 @@ static const struct of_device_id jcore_spi_of_match[] = {
 	{ .compatible = "jcore,spi2" },
 	{},
 };
+MODULE_DEVICE_TABLE(of, jcore_spi_of_match);
 
 static struct platform_driver jcore_spi_driver = {
 	.probe = jcore_spi_probe,

drivers/spi/spi-omap2-mcspi.c

@@ -1386,20 +1386,13 @@ static int omap2_mcspi_probe(struct platform_device *pdev)
 	regs_offset = pdata->regs_offset;
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (r == NULL) {
-		status = -ENODEV;
-		goto free_master;
-	}
-
-	r->start += regs_offset;
-	r->end += regs_offset;
-	mcspi->phys = r->start;
-
 	mcspi->base = devm_ioremap_resource(&pdev->dev, r);
 	if (IS_ERR(mcspi->base)) {
 		status = PTR_ERR(mcspi->base);
 		goto free_master;
 	}
+	mcspi->phys = r->start + regs_offset;
+	mcspi->base += regs_offset;
 
 	mcspi->dev = &pdev->dev;
 

drivers/spi/spi-orion.c

@@ -138,37 +138,62 @@ static int orion_spi_baudrate_set(struct spi_device *spi, unsigned int speed)
 	tclk_hz = clk_get_rate(orion_spi->clk);
 
 	if (devdata->typ == ARMADA_SPI) {
-		unsigned int clk, spr, sppr, sppr2, err;
-		unsigned int best_spr, best_sppr, best_err;
-
-		best_err = speed;
-		best_spr = 0;
-		best_sppr = 0;
-
-		/* Iterate over the valid range looking for best fit */
-		for (sppr = 0; sppr < 8; sppr++) {
-			sppr2 = 0x1 << sppr;
-
-			spr = tclk_hz / sppr2;
-			spr = DIV_ROUND_UP(spr, speed);
-			if ((spr == 0) || (spr > 15))
-				continue;
-
-			clk = tclk_hz / (spr * sppr2);
-			err = speed - clk;
-
-			if (err < best_err) {
-				best_spr = spr;
-				best_sppr = sppr;
-				best_err = err;
-			}
-		}
+		/*
+		 * Given the core_clk (tclk_hz) and the target rate (speed) we
+		 * determine the best values for SPR (in [0 .. 15]) and SPPR (in
+		 * [0..7]) such that
+		 *
+		 * 	core_clk / (SPR * 2 ** SPPR)
+		 *
+		 * is as big as possible but not bigger than speed.
+		 */
 
-		if ((best_sppr == 0) && (best_spr == 0))
-			return -EINVAL;
+		/* best integer divider: */
+		unsigned divider = DIV_ROUND_UP(tclk_hz, speed);
+		unsigned spr, sppr;
+
+		if (divider < 16) {
+			/* This is the easy case, divider is less than 16 */
+			spr = divider;
+			sppr = 0;
+
+		} else {
+			unsigned two_pow_sppr;
+			/*
+			 * Find the highest bit set in divider. This and the
+			 * three next bits define SPR (apart from rounding).
+			 * SPPR is then the number of zero bits that must be
+			 * appended:
+			 */
+			sppr = fls(divider) - 4;
+
+			/*
+			 * As SPR only has 4 bits, we have to round divider up
+			 * to the next multiple of 2 ** sppr.
+			 */
+			two_pow_sppr = 1 << sppr;
+			divider = (divider + two_pow_sppr - 1) & -two_pow_sppr;
+
+			/*
+			 * recalculate sppr as rounding up divider might have
+			 * increased it enough to change the position of the
+			 * highest set bit. In this case the bit that now
+			 * doesn't make it into SPR is 0, so there is no need to
+			 * round again.
+			 */
+			sppr = fls(divider) - 4;
+			spr = divider >> sppr;
+
+			/*
+			 * Now do range checking. SPR is constructed to have a
+			 * width of 4 bits, so this is fine for sure. So we
+			 * still need to check for sppr to fit into 3 bits:
+			 */
+			if (sppr > 7)
+				return -EINVAL;
+		}
 
-		prescale = ((best_sppr & 0x6) << 5) |
-			((best_sppr & 0x1) << 4) | best_spr;
+		prescale = ((sppr & 0x6) << 5) | ((sppr & 0x1) << 4) | spr;
 	} else {
 		/*
 		 * the supported rates are: 4,6,8...30

drivers/spi/spi-pxa2xx.h

@@ -109,7 +109,6 @@ static  inline void pxa2xx_spi_write(const struct driver_data *drv_data,
 #define DONE_STATE ((void *)2)
 #define ERROR_STATE ((void *)-1)
 
-#define IS_DMA_ALIGNED(x)	IS_ALIGNED((unsigned long)(x), DMA_ALIGNMENT)
 #define DMA_ALIGNMENT		8
 
 static inline int pxa25x_ssp_comp(struct driver_data *drv_data)

drivers/spi/spi-rspi.c

@@ -413,7 +413,7 @@ static unsigned int qspi_set_send_trigger(struct rspi_data *rspi,
 	return n;
 }
 
-static void qspi_set_receive_trigger(struct rspi_data *rspi, unsigned int len)
+static int qspi_set_receive_trigger(struct rspi_data *rspi, unsigned int len)
 {
 	unsigned int n;
 
@@ -428,6 +428,7 @@ static void qspi_set_receive_trigger(struct rspi_data *rspi, unsigned int len)
 		qspi_update(rspi, SPBFCR_RXTRG_MASK,
 			     SPBFCR_RXTRG_1B, QSPI_SPBFCR);
 	}
+	return n;
 }
 
 #define set_config_register(spi, n) spi->ops->set_config_register(spi, n)
@@ -785,6 +786,9 @@ static int qspi_transfer_out_in(struct rspi_data *rspi,
 
 static int qspi_transfer_out(struct rspi_data *rspi, struct spi_transfer *xfer)
 {
+	const u8 *tx = xfer->tx_buf;
+	unsigned int n = xfer->len;
+	unsigned int i, len;
 	int ret;
 
 	if (rspi->master->can_dma && __rspi_can_dma(rspi, xfer)) {
@@ -793,9 +797,23 @@ static int qspi_transfer_out(struct rspi_data *rspi, struct spi_transfer *xfer)
 			return ret;
 	}
 
-	ret = rspi_pio_transfer(rspi, xfer->tx_buf, NULL, xfer->len);
-	if (ret < 0)
-		return ret;
+	while (n > 0) {
+		len = qspi_set_send_trigger(rspi, n);
+		if (len == QSPI_BUFFER_SIZE) {
+			ret = rspi_wait_for_tx_empty(rspi);
+			if (ret < 0) {
+				dev_err(&rspi->master->dev, "transmit timeout\n");
+				return ret;
+			}
+			for (i = 0; i < len; i++)
+				rspi_write_data(rspi, *tx++);
+		} else {
+			ret = rspi_pio_transfer(rspi, tx, NULL, n);
+			if (ret < 0)
+				return ret;
+		}
+		n -= len;
+	}
 
 	/* Wait for the last transmission */
 	rspi_wait_for_tx_empty(rspi);
@@ -805,13 +823,37 @@ static int qspi_transfer_out(struct rspi_data *rspi, struct spi_transfer *xfer)
 
 static int qspi_transfer_in(struct rspi_data *rspi, struct spi_transfer *xfer)
 {
+	u8 *rx = xfer->rx_buf;
+	unsigned int n = xfer->len;
+	unsigned int i, len;
+	int ret;
+
 	if (rspi->master->can_dma && __rspi_can_dma(rspi, xfer)) {
 		int ret = rspi_dma_transfer(rspi, NULL, &xfer->rx_sg);
 		if (ret != -EAGAIN)
 			return ret;
 	}
 
-	return rspi_pio_transfer(rspi, NULL, xfer->rx_buf, xfer->len);
+	while (n > 0) {
+		len = qspi_set_receive_trigger(rspi, n);
+		if (len == QSPI_BUFFER_SIZE) {
+			ret = rspi_wait_for_rx_full(rspi);
+			if (ret < 0) {
+				dev_err(&rspi->master->dev, "receive timeout\n");
+				return ret;
+			}
+			for (i = 0; i < len; i++)
+				*rx++ = rspi_read_data(rspi);
+		} else {
+			ret = rspi_pio_transfer(rspi, NULL, rx, n);
+			if (ret < 0)
+				return ret;
+			*rx++ = ret;
+		}
+		n -= len;
+	}
+
+	return 0;
 }
 
 static int qspi_transfer_one(struct spi_master *master, struct spi_device *spi,

drivers/spi/spi-sh-msiof.c

@@ -980,6 +980,7 @@ static const struct of_device_id sh_msiof_match[] = {
 	{ .compatible = "renesas,msiof-r8a7792",   .data = &r8a779x_data },
 	{ .compatible = "renesas,msiof-r8a7793",   .data = &r8a779x_data },
 	{ .compatible = "renesas,msiof-r8a7794",   .data = &r8a779x_data },
+	{ .compatible = "renesas,msiof-r8a7796",   .data = &r8a779x_data },
 	{},
 };
 MODULE_DEVICE_TABLE(of, sh_msiof_match);

drivers/spi/spi-sun4i.c

@@ -46,6 +46,8 @@
 #define SUN4I_CTL_TP				BIT(18)
 
 #define SUN4I_INT_CTL_REG		0x0c
+#define SUN4I_INT_CTL_RF_F34			BIT(4)
+#define SUN4I_INT_CTL_TF_E34			BIT(12)
 #define SUN4I_INT_CTL_TC			BIT(16)
 
 #define SUN4I_INT_STA_REG		0x10
@@ -61,11 +63,14 @@
 #define SUN4I_CLK_CTL_CDR1(div)			(((div) & SUN4I_CLK_CTL_CDR1_MASK) << 8)
 #define SUN4I_CLK_CTL_DRS			BIT(12)
 
+#define SUN4I_MAX_XFER_SIZE			0xffffff
+
 #define SUN4I_BURST_CNT_REG		0x20
-#define SUN4I_BURST_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_BURST_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
 
 #define SUN4I_XMIT_CNT_REG		0x24
-#define SUN4I_XMIT_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_XMIT_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
+
 
 #define SUN4I_FIFO_STA_REG		0x28
 #define SUN4I_FIFO_STA_RF_CNT_MASK		0x7f
@@ -96,6 +101,31 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value)
 	writel(value, sspi->base_addr + reg);
 }
 
+static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG);
+
+	reg >>= SUN4I_FIFO_STA_TF_CNT_BITS;
+
+	return reg & SUN4I_FIFO_STA_TF_CNT_MASK;
+}
+
+static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+
+	reg |= mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
+static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+
+	reg &= ~mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
 static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 {
 	u32 reg, cnt;
@@ -118,10 +148,13 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 
 static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len)
 {
+	u32 cnt;
 	u8 byte;
 
-	if (len > sspi->len)
-		len = sspi->len;
+	/* See how much data we can fit */
+	cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi);
+
+	len = min3(len, (int)cnt, sspi->len);
 
 	while (len--) {
 		byte = sspi->tx_buf ? *sspi->tx_buf++ : 0;
@@ -184,10 +217,10 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	u32 reg;
 
 	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN4I_FIFO_DEPTH)
+	if (tfr->len > SUN4I_MAX_XFER_SIZE)
 		return -EMSGSIZE;
 
-	if (tfr->tx_buf && tfr->len >= SUN4I_FIFO_DEPTH)
+	if (tfr->tx_buf && tfr->len >= SUN4I_MAX_XFER_SIZE)
 		return -EMSGSIZE;
 
 	reinit_completion(&sspi->done);
@@ -286,7 +319,11 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH - 1);
 
 	/* Enable the interrupts */
-	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC);
+	sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TC |
+					 SUN4I_INT_CTL_RF_F34);
+	/* Only enable Tx FIFO interrupt if we really need it */
+	if (tx_len > SUN4I_FIFO_DEPTH)
+		sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
 
 	/* Start the transfer */
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
@@ -306,7 +343,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
 
 out:
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
@@ -322,10 +358,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id)
 	/* Transfer complete */
 	if (status & SUN4I_INT_CTL_TC) {
 		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC);
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
 		complete(&sspi->done);
 		return IRQ_HANDLED;
 	}
 
+	/* Receive FIFO 3/4 full */
+	if (status & SUN4I_INT_CTL_RF_F34) {
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
+		/* Only clear the interrupt _after_ draining the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34);
+		return IRQ_HANDLED;
+	}
+
+	/* Transmit FIFO 3/4 empty */
+	if (status & SUN4I_INT_CTL_TF_E34) {
+		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
+
+		if (!sspi->len)
+			/* nothing left to transmit */
+			sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
+
+		/* Only clear the interrupt _after_ re-seeding the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34);
+
+		return IRQ_HANDLED;
+	}
+
 	return IRQ_NONE;
 }
 

drivers/spi/spi-sun6i.c

@@ -17,6 +17,7 @@
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
 #include <linux/reset.h>
@@ -24,6 +25,7 @@
 #include <linux/spi/spi.h>
 
 #define SUN6I_FIFO_DEPTH		128
+#define SUN8I_FIFO_DEPTH		64
 
 #define SUN6I_GBL_CTL_REG		0x04
 #define SUN6I_GBL_CTL_BUS_ENABLE		BIT(0)
@@ -90,6 +92,7 @@ struct sun6i_spi {
 	const u8		*tx_buf;
 	u8			*rx_buf;
 	int			len;
+	unsigned long		fifo_depth;
 };
 
 static inline u32 sun6i_spi_read(struct sun6i_spi *sspi, u32 reg)
@@ -155,7 +158,9 @@ static void sun6i_spi_set_cs(struct spi_device *spi, bool enable)
 
 static size_t sun6i_spi_max_transfer_size(struct spi_device *spi)
 {
-	return SUN6I_FIFO_DEPTH - 1;
+	struct sun6i_spi *sspi = spi_master_get_devdata(spi->master);
+
+	return sspi->fifo_depth - 1;
 }
 
 static int sun6i_spi_transfer_one(struct spi_master *master,
@@ -170,7 +175,7 @@ static int sun6i_spi_transfer_one(struct spi_master *master,
 	u32 reg;
 
 	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN6I_FIFO_DEPTH)
+	if (tfr->len > sspi->fifo_depth)
 		return -EINVAL;
 
 	reinit_completion(&sspi->done);
@@ -265,7 +270,7 @@ static int sun6i_spi_transfer_one(struct spi_master *master,
 			SUN6I_BURST_CTL_CNT_STC(tx_len));
 
 	/* Fill the TX FIFO */
-	sun6i_spi_fill_fifo(sspi, SUN6I_FIFO_DEPTH);
+	sun6i_spi_fill_fifo(sspi, sspi->fifo_depth);
 
 	/* Enable the interrupts */
 	sun6i_spi_write(sspi, SUN6I_INT_CTL_REG, SUN6I_INT_CTL_TC);
@@ -288,7 +293,7 @@ static int sun6i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun6i_spi_drain_fifo(sspi, SUN6I_FIFO_DEPTH);
+	sun6i_spi_drain_fifo(sspi, sspi->fifo_depth);
 
 out:
 	sun6i_spi_write(sspi, SUN6I_INT_CTL_REG, 0);
@@ -398,6 +403,8 @@ static int sun6i_spi_probe(struct platform_device *pdev)
 	}
 
 	sspi->master = master;
+	sspi->fifo_depth = (unsigned long)of_device_get_match_data(&pdev->dev);
+
 	master->max_speed_hz = 100 * 1000 * 1000;
 	master->min_speed_hz = 3 * 1000;
 	master->set_cs = sun6i_spi_set_cs;
@@ -470,7 +477,8 @@ static int sun6i_spi_remove(struct platform_device *pdev)
 }
 
 static const struct of_device_id sun6i_spi_match[] = {
-	{ .compatible = "allwinner,sun6i-a31-spi", },
+	{ .compatible = "allwinner,sun6i-a31-spi", .data = (void *)SUN6I_FIFO_DEPTH },
+	{ .compatible = "allwinner,sun8i-h3-spi",  .data = (void *)SUN8I_FIFO_DEPTH },
 	{}
 };
 MODULE_DEVICE_TABLE(of, sun6i_spi_match);

drivers/spi/spi-ti-qspi.c

@@ -411,6 +411,7 @@ static int ti_qspi_dma_xfer(struct ti_qspi *qspi, dma_addr_t dma_dst,
 	tx->callback = ti_qspi_dma_callback;
 	tx->callback_param = qspi;
 	cookie = tx->tx_submit(tx);
+	reinit_completion(&qspi->transfer_complete);
 
 	ret = dma_submit_error(cookie);
 	if (ret) {

drivers/spi/spi-topcliff-pch.c

@@ -1268,11 +1268,8 @@ static void pch_spi_free_resources(struct pch_spi_board_data *board_dat,
 static int pch_spi_get_resources(struct pch_spi_board_data *board_dat,
 				 struct pch_spi_data *data)
 {
-	int retval = 0;
-
 	dev_dbg(&board_dat->pdev->dev, "%s ENTRY\n", __func__);
 
-
 	/* reset PCH SPI h/w */
 	pch_spi_reset(data->master);
 	dev_dbg(&board_dat->pdev->dev,
@@ -1280,15 +1277,7 @@ static int pch_spi_get_resources(struct pch_spi_board_data *board_dat,
 
 	dev_dbg(&board_dat->pdev->dev, "%s data->irq_reg_sts=true\n", __func__);
 
-	if (retval != 0) {
-		dev_err(&board_dat->pdev->dev,
-			"%s FAIL:invoking pch_spi_free_resources\n", __func__);
-		pch_spi_free_resources(board_dat, data);
-	}
-
-	dev_dbg(&board_dat->pdev->dev, "%s Return=%d\n", __func__, retval);
-
-	return retval;
+	return 0;
 }
 
 static void pch_free_dma_buf(struct pch_spi_board_data *board_dat,

drivers/spi/spi-xlp.c

@@ -451,6 +451,7 @@ static const struct of_device_id xlp_spi_dt_id[] = {
 	{ .compatible = "netlogic,xlp832-spi" },
 	{ },
 };
+MODULE_DEVICE_TABLE(of, xlp_spi_dt_id);
 
 static struct platform_driver xlp_spi_driver = {
 	.probe	= xlp_spi_probe,

drivers/spi/spi.c

@@ -697,10 +697,15 @@ static void spi_set_cs(struct spi_device *spi, bool enable)
 	if (spi->mode & SPI_CS_HIGH)
 		enable = !enable;
 
-	if (gpio_is_valid(spi->cs_gpio))
+	if (gpio_is_valid(spi->cs_gpio)) {
 		gpio_set_value(spi->cs_gpio, !enable);
-	else if (spi->master->set_cs)
+		/* Some SPI masters need both GPIO CS & slave_select */
+		if ((spi->master->flags & SPI_MASTER_GPIO_SS) &&
+		    spi->master->set_cs)
+			spi->master->set_cs(spi, !enable);
+	} else if (spi->master->set_cs) {
 		spi->master->set_cs(spi, !enable);
+	}
 }
 
 #ifdef CONFIG_HAS_DMA
@@ -720,6 +725,7 @@ static int spi_map_buf(struct spi_master *master, struct device *dev,
 	int desc_len;
 	int sgs;
 	struct page *vm_page;
+	struct scatterlist *sg;
 	void *sg_buf;
 	size_t min;
 	int i, ret;
@@ -738,6 +744,7 @@ static int spi_map_buf(struct spi_master *master, struct device *dev,
 	if (ret != 0)
 		return ret;
 
+	sg = &sgt->sgl[0];
 	for (i = 0; i < sgs; i++) {
 
 		if (vmalloced_buf || kmap_buf) {
@@ -751,16 +758,17 @@ static int spi_map_buf(struct spi_master *master, struct device *dev,
 				sg_free_table(sgt);
 				return -ENOMEM;
 			}
-			sg_set_page(&sgt->sgl[i], vm_page,
+			sg_set_page(sg, vm_page,
 				    min, offset_in_page(buf));
 		} else {
 			min = min_t(size_t, len, desc_len);
 			sg_buf = buf;
-			sg_set_buf(&sgt->sgl[i], sg_buf, min);
+			sg_set_buf(sg, sg_buf, min);
 		}
 
 		buf += min;
 		len -= min;
+		sg = sg_next(sg);
 	}
 
 	ret = dma_map_sg(dev, sgt->sgl, sgt->nents, dir);
@@ -1034,8 +1042,14 @@ static int spi_transfer_one_message(struct spi_master *master,
 		if (msg->status != -EINPROGRESS)
 			goto out;
 
-		if (xfer->delay_usecs)
-			udelay(xfer->delay_usecs);
+		if (xfer->delay_usecs) {
+			u16 us = xfer->delay_usecs;
+
+			if (us <= 10)
+				udelay(us);
+			else
+				usleep_range(us, us + DIV_ROUND_UP(us, 10));
+		}
 
 		if (xfer->cs_change) {
 			if (list_is_last(&xfer->transfer_list,

drivers/spi/spidev.c

@@ -696,6 +696,7 @@ static struct class *spidev_class;
 static const struct of_device_id spidev_dt_ids[] = {
 	{ .compatible = "rohm,dh2228fv" },
 	{ .compatible = "lineartechnology,ltc2488" },
+	{ .compatible = "ge,achc" },
 	{},
 };
 MODULE_DEVICE_TABLE(of, spidev_dt_ids);

include/linux/spi/spi.h

@@ -442,6 +442,7 @@ struct spi_master {
 #define SPI_MASTER_NO_TX	BIT(2)		/* can't do buffer write */
 #define SPI_MASTER_MUST_RX      BIT(3)		/* requires rx */
 #define SPI_MASTER_MUST_TX      BIT(4)		/* requires tx */
+#define SPI_MASTER_GPIO_SS      BIT(5)		/* GPIO CS must select slave */
 
 	/*
 	 * on some hardware transfer / message size may be constrained

tools/spi/spidev_test.c

@@ -315,7 +315,7 @@ static void transfer_file(int fd, char *filename)
 		pabort("can't stat input file");
 
 	tx_fd = open(filename, O_RDONLY);
-	if (fd < 0)
+	if (tx_fd < 0)
 		pabort("can't open input file");
 
 	tx = malloc(sb.st_size);