提交 b94ea275 编写于 作者: P Paul Mundt

sh: Kill off the cayman and microdev special heartbeat code.

These can use the generic code instead.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
上级 ca0c14e4
......@@ -2,4 +2,3 @@
# Makefile for the Hitachi Cayman specific parts of the kernel
#
obj-y := setup.o irq.o
obj-$(CONFIG_HEARTBEAT) += led.o
/*
* arch/sh/boards/cayman/led.c
*
* Copyright (C) 2002 Stuart Menefy <stuart.menefy@st.com>
*
* May be copied or modified under the terms of the GNU General Public
* License. See linux/COPYING for more information.
*
* Flash the LEDs
*/
#include <asm/io.h>
/*
** It is supposed these functions to be used for a low level
** debugging (via Cayman LEDs), hence to be available as soon
** as possible.
** Unfortunately Cayman LEDs relies on Cayman EPLD to be mapped
** (this happen when IRQ are initialized... quite late).
** These triky dependencies should be removed. Temporary, it
** may be enough to NOP until EPLD is mapped.
*/
extern unsigned long epld_virt;
#define LED_ADDR (epld_virt + 0x008)
#define HDSP2534_ADDR (epld_virt + 0x100)
void mach_led(int position, int value)
{
if (!epld_virt)
return;
if (value)
ctrl_outl(0, LED_ADDR);
else
ctrl_outl(1, LED_ADDR);
}
void mach_alphanum(int position, unsigned char value)
{
if (!epld_virt)
return;
ctrl_outb(value, HDSP2534_ADDR + 0xe0 + (position << 2));
}
void mach_alphanum_brightness(int setting)
{
ctrl_outb(setting & 7, HDSP2534_ADDR + 0xc0);
}
......@@ -3,6 +3,3 @@
#
obj-y := setup.o irq.o io.o
obj-$(CONFIG_HEARTBEAT) += led.o
/*
* linux/arch/sh/boards/superh/microdev/led.c
*
* Copyright (C) 2002 Stuart Menefy <stuart.menefy@st.com>
* Copyright (C) 2003 Richard Curnow (Richard.Curnow@superh.com)
*
* May be copied or modified under the terms of the GNU General Public
* License. See linux/COPYING for more information.
*
*/
#include <asm/io.h>
#define LED_REGISTER 0xa6104d20
static void mach_led_d9(int value)
{
unsigned long reg;
reg = ctrl_inl(LED_REGISTER);
reg &= ~1;
reg |= (value & 1);
ctrl_outl(reg, LED_REGISTER);
return;
}
static void mach_led_d10(int value)
{
unsigned long reg;
reg = ctrl_inl(LED_REGISTER);
reg &= ~2;
reg |= ((value & 1) << 1);
ctrl_outl(reg, LED_REGISTER);
return;
}
#ifdef CONFIG_HEARTBEAT
#include <linux/sched.h>
static unsigned char banner_table[] = {
0x11, 0x01, 0x11, 0x01, 0x11, 0x03,
0x11, 0x01, 0x11, 0x01, 0x13, 0x03,
0x11, 0x01, 0x13, 0x01, 0x13, 0x01, 0x11, 0x03,
0x11, 0x03,
0x11, 0x01, 0x13, 0x01, 0x11, 0x03,
0x11, 0x01, 0x11, 0x01, 0x11, 0x01, 0x11, 0x07,
0x13, 0x01, 0x13, 0x03,
0x11, 0x01, 0x11, 0x03,
0x13, 0x01, 0x11, 0x01, 0x13, 0x01, 0x11, 0x03,
0x11, 0x01, 0x13, 0x01, 0x11, 0x03,
0x13, 0x01, 0x13, 0x01, 0x13, 0x03,
0x13, 0x01, 0x11, 0x01, 0x11, 0x03,
0x11, 0x03,
0x11, 0x01, 0x11, 0x01, 0x11, 0x01, 0x13, 0x07,
0xff
};
static void banner(void)
{
static int pos = 0;
static int count = 0;
if (count) {
count--;
} else {
int val = banner_table[pos];
if (val == 0xff) {
pos = 0;
val = banner_table[pos];
}
pos++;
mach_led_d10((val >> 4) & 1);
count = 10 * (val & 0xf);
}
}
/* From heartbeat_harp in the stboards directory */
/* acts like an actual heart beat -- ie thump-thump-pause... */
void microdev_heartbeat(void)
{
static unsigned cnt = 0, period = 0, dist = 0;
if (cnt == 0 || cnt == dist)
mach_led_d9(1);
else if (cnt == 7 || cnt == dist+7)
mach_led_d9(0);
if (++cnt > period) {
cnt = 0;
/* The hyperbolic function below modifies the heartbeat period
* length in dependency of the current (5min) load. It goes
* through the points f(0)=126, f(1)=86, f(5)=51,
* f(inf)->30. */
period = ((672<<FSHIFT)/(5*avenrun[0]+(7<<FSHIFT))) + 30;
dist = period / 4;
}
banner();
}
#endif
......@@ -18,12 +18,6 @@
#include <asm/io.h>
#include <asm/machvec.h>
extern void microdev_heartbeat(void);
/****************************************************************************/
/*
* Setup for the SMSC FDC37C93xAPM
*/
......@@ -398,8 +392,4 @@ static struct sh_machine_vector mv_sh4202_microdev __initmv = {
.mv_outsl = microdev_outsl,
.mv_init_irq = init_microdev_irq,
#ifdef CONFIG_HEARTBEAT
.mv_heartbeat = microdev_heartbeat,
#endif
};
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册