提交 a8e93ed8 编写于 作者: D David Brownell 提交者: Haavard Skinnemoen

[AVR32] Make STK1000 mux settings configurable

This adds some STK1002-specific config options covering the jumper settings,
so the kernel can automatically be configured to include the relevant devices.

One of them replaces the previous internal SW2_DEFAULT setting; SPI config
is affected by two of the jumpers; and a fourth one switches between LCD and
the second Ethernet connector.  (There's more that to be done.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
上级 9e58e185
......@@ -113,6 +113,10 @@ config BOARD_ATNGW100
bool "ATNGW100 Network Gateway"
endchoice
if BOARD_ATSTK1000
source "arch/avr32/boards/atstk1000/Kconfig"
endif
choice
prompt "Boot loader type"
default LOADER_U_BOOT
......
# STK1000 customization
if BOARD_ATSTK1002
config BOARD_ATSTK1002_CUSTOM
bool "Non-default STK-1002 jumper settings"
help
You will normally leave the jumpers on the CPU card at their
default settings. If you need to use certain peripherals,
you will need to change some of those jumpers.
if BOARD_ATSTK1002_CUSTOM
config BOARD_ATSTK1002_SW1_CUSTOM
bool "SW1: use SSC1 (not SPI0)"
help
This also prevents using the external DAC as an audio interface,
and means you can't initialize the on-board QVGA display.
config BOARD_ATSTK1002_SW2_CUSTOM
bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)"
help
If you change this you'll want an updated boot loader putting
the console on UART-C not UART-A.
config BOARD_ATSTK1002_SW3_CUSTOM
bool "SW3: use TIMER1 (not SSC0 and GCLK)"
help
This also prevents using the external DAC as an audio interface.
config BOARD_ATSTK1002_SW4_CUSTOM
bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)"
help
To use the camera interface you'll need a custom card (on the
PCI-format connector) connect a video sensor.
config BOARD_ATSTK1002_SW5_CUSTOM
bool "SW5: use MACB1 (not LCDC)"
config BOARD_ATSTK1002_SW6_CUSTOM
bool "SW6: more GPIOs (not MACB0)"
endif # custom
config BOARD_ATSTK1002_SPI1
bool "Configure SPI1 controller"
depends on !BOARD_ATSTK1002_SW4_CUSTOM
help
All the signals for the second SPI controller are available on
GPIO lines and accessed through the J1 jumper block. Say "y"
here to configure that SPI controller.
endif # stk 1002
......@@ -27,7 +27,6 @@
#include "atstk1000.h"
#define SW2_DEFAULT /* MMCI and UART_A available */
struct eth_addr {
u8 addr[6];
......@@ -36,6 +35,7 @@ struct eth_addr {
static struct eth_addr __initdata hw_addr[2];
static struct eth_platform_data __initdata eth_data[2];
#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM
static struct spi_board_info spi0_board_info[] __initdata = {
{
/* QVGA display */
......@@ -45,6 +45,13 @@ static struct spi_board_info spi0_board_info[] __initdata = {
.mode = SPI_MODE_3,
},
};
#endif
#ifdef CONFIG_BOARD_ATSTK1002_SPI1
static struct spi_board_info spi1_board_info[] __initdata = { {
/* patch in custom entries here */
} };
#endif
/*
* The next two functions should go away as the boot loader is
......@@ -103,10 +110,10 @@ static void __init set_hw_addr(struct platform_device *pdev)
void __init setup_board(void)
{
#ifdef SW2_DEFAULT
at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */
#else
#ifdef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM
at32_map_usart(0, 1); /* USART 0/B: /dev/ttyS1, IRDA */
#else
at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */
#endif
/* USART 2/unused: expansion connector */
at32_map_usart(3, 2); /* USART 3/C: /dev/ttyS2, DB9 */
......@@ -140,18 +147,27 @@ static int __init atstk1002_init(void)
at32_add_system_devices();
#ifdef SW2_DEFAULT
at32_add_device_usart(0);
#else
#ifdef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM
at32_add_device_usart(1);
#else
at32_add_device_usart(0);
#endif
at32_add_device_usart(2);
set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
#ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM
at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
#endif
#ifdef CONFIG_BOARD_ATSTK1002_SPI1
at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
#endif
#ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM
set_hw_addr(at32_add_device_eth(1, &eth_data[1]));
#else
at32_add_device_lcdc(0, &atstk1000_lcdc_data,
fbmem_start, fbmem_size);
#endif
return 0;
}
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册