提交 97e2c402 编写于 作者: C Christian Lamparter 提交者: John W. Linville

carl9170: fix usb pm suspend->resume woes

This patch revamps some common code-paths which are
shared between (re-)initialization and suspend/resume
subroutines. It also adds some helpful comments
about quirks and associated difficulties.

It's quite big, but it should fix #25382:
<https://bugzilla.kernel.org/show_bug.cgi?id=25382>

And hopefully the code is robust enough to deal with
all possible suspend/resume scenarios without requiring
the user to do any sort of manual and possibly
dangerous work.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
上级 3b386510
......@@ -834,7 +834,7 @@ static int carl9170_usb_load_firmware(struct ar9170 *ar)
if (err)
goto err_out;
/* firmware restarts cmd counter */
/* now, start the command response counter */
ar->cmd_seq = -1;
return 0;
......@@ -851,7 +851,12 @@ int carl9170_usb_restart(struct ar9170 *ar)
if (ar->intf->condition != USB_INTERFACE_BOUND)
return 0;
/* Disable command response sequence counter. */
/*
* Disable the command response sequence counter check.
* We already know that the device/firmware is in a bad state.
* So, no extra points are awarded to anyone who reminds the
* driver about that.
*/
ar->cmd_seq = -2;
err = carl9170_reboot(ar);
......@@ -903,6 +908,15 @@ static int carl9170_usb_init_device(struct ar9170 *ar)
{
int err;
/*
* The carl9170 firmware let's the driver know when it's
* ready for action. But we have to be prepared to gracefully
* handle all spurious [flushed] messages after each (re-)boot.
* Thus the command response counter remains disabled until it
* can be safely synchronized.
*/
ar->cmd_seq = -2;
err = carl9170_usb_send_rx_irq_urb(ar);
if (err)
goto err_out;
......@@ -911,14 +925,21 @@ static int carl9170_usb_init_device(struct ar9170 *ar)
if (err)
goto err_unrx;
err = carl9170_usb_open(ar);
if (err)
goto err_unrx;
mutex_lock(&ar->mutex);
err = carl9170_usb_load_firmware(ar);
mutex_unlock(&ar->mutex);
if (err)
goto err_unrx;
goto err_stop;
return 0;
err_stop:
carl9170_usb_stop(ar);
err_unrx:
carl9170_usb_cancel_urbs(ar);
......@@ -964,10 +985,6 @@ static void carl9170_usb_firmware_finish(struct ar9170 *ar)
if (err)
goto err_freefw;
err = carl9170_usb_open(ar);
if (err)
goto err_unrx;
err = carl9170_register(ar);
carl9170_usb_stop(ar);
......@@ -1043,7 +1060,6 @@ static int carl9170_usb_probe(struct usb_interface *intf,
atomic_set(&ar->rx_work_urbs, 0);
atomic_set(&ar->rx_anch_urbs, 0);
atomic_set(&ar->rx_pool_urbs, 0);
ar->cmd_seq = -2;
usb_get_dev(ar->udev);
......@@ -1090,10 +1106,6 @@ static int carl9170_usb_suspend(struct usb_interface *intf,
carl9170_usb_cancel_urbs(ar);
/*
* firmware automatically reboots for usb suspend.
*/
return 0;
}
......@@ -1106,12 +1118,20 @@ static int carl9170_usb_resume(struct usb_interface *intf)
return -ENODEV;
usb_unpoison_anchored_urbs(&ar->rx_anch);
carl9170_set_state(ar, CARL9170_STOPPED);
err = carl9170_usb_init_device(ar);
if (err)
goto err_unrx;
/*
* The USB documentation demands that [for suspend] all traffic
* to and from the device has to stop. This would be fine, but
* there's a catch: the device[usb phy] does not come back.
*
* Upon resume the firmware will "kill" itself and the
* boot-code sorts out the magic voodoo.
* Not very nice, but there's not much what could go wrong.
*/
msleep(1100);
err = carl9170_usb_open(ar);
err = carl9170_usb_init_device(ar);
if (err)
goto err_unrx;
......@@ -1133,6 +1153,7 @@ static struct usb_driver carl9170_driver = {
#ifdef CONFIG_PM
.suspend = carl9170_usb_suspend,
.resume = carl9170_usb_resume,
.reset_resume = carl9170_usb_resume,
#endif /* CONFIG_PM */
};
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册