提交 8395ae83 编写于 作者: B Bruce Allan 提交者: David S. Miller

e1000e: 82577/8/9 issues with device in Sx

When going to Sx, disable gigabit in PHY (e1000_oem_bits_config_ich8lan)
in addition to the MAC before configuring PHY wakeup otherwise the PHY
configuration writes might be missed.  Also write the LED configuration
and SMBus address to the PHY registers (e1000_oem_bits_config_ich8lan and
e1000_write_smbus_addr, respectively).  The reset is no longer needed
since re-auto-negotiation is forced in e1000_oem_bits_config_ich8lan and
leaving it in causes issues with auto-negotiating the link.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 94e22389
......@@ -125,6 +125,7 @@
/* SMBus Address Phy Register */
#define HV_SMB_ADDR PHY_REG(768, 26)
#define HV_SMB_ADDR_MASK 0x007F
#define HV_SMB_ADDR_PEC_EN 0x0200
#define HV_SMB_ADDR_VALID 0x0080
......@@ -894,6 +895,34 @@ static s32 e1000_check_reset_block_ich8lan(struct e1000_hw *hw)
return (fwsm & E1000_ICH_FWSM_RSPCIPHY) ? 0 : E1000_BLK_PHY_RESET;
}
/**
* e1000_write_smbus_addr - Write SMBus address to PHY needed during Sx states
* @hw: pointer to the HW structure
*
* Assumes semaphore already acquired.
*
**/
static s32 e1000_write_smbus_addr(struct e1000_hw *hw)
{
u16 phy_data;
u32 strap = er32(STRAP);
s32 ret_val = 0;
strap &= E1000_STRAP_SMBUS_ADDRESS_MASK;
ret_val = e1000_read_phy_reg_hv_locked(hw, HV_SMB_ADDR, &phy_data);
if (ret_val)
goto out;
phy_data &= ~HV_SMB_ADDR_MASK;
phy_data |= (strap >> E1000_STRAP_SMBUS_ADDRESS_SHIFT);
phy_data |= HV_SMB_ADDR_PEC_EN | HV_SMB_ADDR_VALID;
ret_val = e1000_write_phy_reg_hv_locked(hw, HV_SMB_ADDR, phy_data);
out:
return ret_val;
}
/**
* e1000_sw_lcd_config_ich8lan - SW-based LCD Configuration
* @hw: pointer to the HW structure
......@@ -970,12 +999,7 @@ static s32 e1000_sw_lcd_config_ich8lan(struct e1000_hw *hw)
* When both NVM bits are cleared, SW will configure
* them instead.
*/
data = er32(STRAP);
data &= E1000_STRAP_SMBUS_ADDRESS_MASK;
reg_data = data >> E1000_STRAP_SMBUS_ADDRESS_SHIFT;
reg_data |= HV_SMB_ADDR_PEC_EN | HV_SMB_ADDR_VALID;
ret_val = e1000_write_phy_reg_hv_locked(hw, HV_SMB_ADDR,
reg_data);
ret_val = e1000_write_smbus_addr(hw);
if (ret_val)
goto out;
......@@ -3460,13 +3484,20 @@ void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw)
void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw)
{
u32 phy_ctrl;
s32 ret_val;
phy_ctrl = er32(PHY_CTRL);
phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU | E1000_PHY_CTRL_GBE_DISABLE;
ew32(PHY_CTRL, phy_ctrl);
if (hw->mac.type >= e1000_pchlan)
e1000_phy_hw_reset_ich8lan(hw);
if (hw->mac.type >= e1000_pchlan) {
e1000_oem_bits_config_ich8lan(hw, true);
ret_val = hw->phy.ops.acquire(hw);
if (ret_val)
return;
e1000_write_smbus_addr(hw);
hw->phy.ops.release(hw);
}
}
/**
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册