ARM: at91: add pinctrl support

This is also include the gpio controller as the IP share both.
Each soc will have to describe the SoC limitation and pin configuration via
DT.

This will allow to do not need to touch the C code when adding new SoC if the
IP version is supported.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
上级 97e5e625
* Atmel AT91 Pinmux Controller
The AT91 Pinmux Controler, enables the IC
to share one PAD to several functional blocks. The sharing is done by
multiplexing the PAD input/output signals. For each PAD there are up to
8 muxing options (called periph modes). Since different modules require
different PAD settings (like pull up, keeper, etc) the contoller controls
also the PAD settings parameters.
Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the meaning of the
phrase "pin configuration node".
Atmel AT91 pin configuration node is a node of a group of pins which can be
used for a specific device or function. This node represents both mux and config
of the pins in that group. The 'pins' selects the function mode(also named pin
mode) this pin can work on and the 'config' configures various pad settings
such as pull-up, multi drive, etc.
Required properties for iomux controller:
- compatible: "atmel,at91rm9200-pinctrl"
- atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be
configured in this periph mode. All the periph and bank need to be describe.
How to create such array:
Each column will represent the possible peripheral of the pinctrl
Each line will represent a pio bank
Take an example on the 9260
Peripheral: 2 ( A and B)
Bank: 3 (A, B and C)
=>
/* A B */
0xffffffff 0xffc00c3b /* pioA */
0xffffffff 0x7fff3ccf /* pioB */
0xffffffff 0x007fffff /* pioC */
For each peripheral/bank we will descibe in a u32 if a pin can can be
configured in it by putting 1 to the pin bit (1 << pin)
Let's take the pioA on peripheral B
From the datasheet Table 10-2.
Peripheral B
PA0 MCDB0
PA1 MCCDB
PA2
PA3 MCDB3
PA4 MCDB2
PA5 MCDB1
PA6
PA7
PA8
PA9
PA10 ETX2
PA11 ETX3
PA12
PA13
PA14
PA15
PA16
PA17
PA18
PA19
PA20
PA21
PA22 ETXER
PA23 ETX2
PA24 ETX3
PA25 ERX2
PA26 ERX3
PA27 ERXCK
PA28 ECRS
PA29 ECOL
PA30 RXD4
PA31 TXD4
=> 0xffc00c3b
Required properties for pin configuration node:
- atmel,pins: 4 integers array, represents a group of pins mux and config
setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
The PERIPH 0 means gpio.
Bits used for CONFIG:
PULL_UP(1 << 0): indicate this pin need a pull up.
MULTIDRIVE(1 << 1): indicate this pin need to be configured as multidrive.
NOTE:
Some requirements for using atmel,at91rm9200-pinctrl binding:
1. We have pin function node defined under at91 controller node to represent
what pinmux functions this SoC supports.
2. The driver can use the function node's name and pin configuration node's
name describe the pin function and group hierarchy.
For example, Linux at91 pinctrl driver takes the function node's name
as the function name and pin configuration node's name as group name to
create the map table.
3. Each pin configuration node should have a phandle, devices can set pins
configurations by referring to the phandle of that pin configuration node.
4. The gpio controller must be describe in the pinctrl simple-bus.
Examples:
pinctrl@fffff400 {
#address-cells = <1>;
#size-cells = <1>;
ranges;
compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
reg = <0xfffff400 0x600>;
atmel,mux-mask = <
/* A B */
0xffffffff 0xffc00c3b /* pioA */
0xffffffff 0x7fff3ccf /* pioB */
0xffffffff 0x007fffff /* pioC */
>;
/* shared pinctrl settings */
dbgu {
pinctrl_dbgu: dbgu-0 {
atmel,pins =
<1 14 0x1 0x0 /* PB14 periph A */
1 15 0x1 0x1>; /* PB15 periph with pullup */
};
};
};
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
interrupts = <1 4 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
};
......@@ -329,6 +329,8 @@ config ARCH_AT91
select IRQ_DOMAIN
select NEED_MACH_GPIO_H
select NEED_MACH_IO_H if PCCARD
select PINCTRL
select PINCTRL_AT91 if USE_OF
help
This enables support for systems based on Atmel
AT91RM9200 and AT91SAM9* processors.
......
......@@ -30,8 +30,6 @@
static const struct of_device_id irq_of_match[] __initconst = {
{ .compatible = "atmel,at91rm9200-aic", .data = at91_aic_of_init },
{ .compatible = "atmel,at91rm9200-gpio", .data = at91_gpio_of_irq_setup },
{ .compatible = "atmel,at91sam9x5-gpio", .data = at91_gpio_of_irq_setup },
{ /*sentinel*/ }
};
......
......@@ -23,8 +23,6 @@
#include <linux/io.h>
#include <linux/irqdomain.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/of_gpio.h>
#include <asm/mach/irq.h>
......@@ -717,80 +715,6 @@ postcore_initcall(at91_gpio_debugfs_init);
*/
static struct lock_class_key gpio_lock_class;
#if defined(CONFIG_OF)
static int at91_gpio_irq_map(struct irq_domain *h, unsigned int virq,
irq_hw_number_t hw)
{
struct at91_gpio_chip *at91_gpio = h->host_data;
irq_set_lockdep_class(virq, &gpio_lock_class);
/*
* Can use the "simple" and not "edge" handler since it's
* shorter, and the AIC handles interrupts sanely.
*/
irq_set_chip_and_handler(virq, &gpio_irqchip,
handle_simple_irq);
set_irq_flags(virq, IRQF_VALID);
irq_set_chip_data(virq, at91_gpio);
return 0;
}
static struct irq_domain_ops at91_gpio_ops = {
.map = at91_gpio_irq_map,
.xlate = irq_domain_xlate_twocell,
};
int __init at91_gpio_of_irq_setup(struct device_node *node,
struct device_node *parent)
{
struct at91_gpio_chip *prev = NULL;
int alias_idx = of_alias_get_id(node, "gpio");
struct at91_gpio_chip *at91_gpio = &gpio_chip[alias_idx];
/* Setup proper .irq_set_type function */
if (has_pio3())
gpio_irqchip.irq_set_type = alt_gpio_irq_type;
else
gpio_irqchip.irq_set_type = gpio_irq_type;
/* Disable irqs of this PIO controller */
__raw_writel(~0, at91_gpio->regbase + PIO_IDR);
/* Setup irq domain */
at91_gpio->domain = irq_domain_add_linear(node, at91_gpio->chip.ngpio,
&at91_gpio_ops, at91_gpio);
if (!at91_gpio->domain)
panic("at91_gpio.%d: couldn't allocate irq domain (DT).\n",
at91_gpio->pioc_idx);
/* Setup chained handler */
if (at91_gpio->pioc_idx)
prev = &gpio_chip[at91_gpio->pioc_idx - 1];
/* The toplevel handler handles one bank of GPIOs, except
* on some SoC it can handles up to three...
* We only set up the handler for the first of the list.
*/
if (prev && prev->next == at91_gpio)
return 0;
at91_gpio->pioc_virq = irq_create_mapping(irq_find_host(parent),
at91_gpio->pioc_hwirq);
irq_set_chip_data(at91_gpio->pioc_virq, at91_gpio);
irq_set_chained_handler(at91_gpio->pioc_virq, gpio_irq_handler);
return 0;
}
#else
int __init at91_gpio_of_irq_setup(struct device_node *node,
struct device_node *parent)
{
return -EINVAL;
}
#endif
/*
* irqdomain initialization: pile up irqdomains on top of AIC range
*/
......@@ -989,85 +913,6 @@ static int __init at91_gpio_setup_clk(int idx)
return -EINVAL;
}
#ifdef CONFIG_OF_GPIO
static void __init of_at91_gpio_init_one(struct device_node *np)
{
int alias_idx;
struct at91_gpio_chip *at91_gpio;
uint32_t ngpio;
if (!np)
return;
alias_idx = of_alias_get_id(np, "gpio");
if (alias_idx >= MAX_GPIO_BANKS) {
pr_err("at91_gpio, failed alias idx(%d) > MAX_GPIO_BANKS(%d), ignoring.\n",
alias_idx, MAX_GPIO_BANKS);
return;
}
at91_gpio = &gpio_chip[alias_idx];
at91_gpio->chip.base = alias_idx * MAX_NB_GPIO_PER_BANK;
at91_gpio->regbase = of_iomap(np, 0);
if (!at91_gpio->regbase) {
pr_err("at91_gpio.%d, failed to map registers, ignoring.\n",
alias_idx);
return;
}
/* Get the interrupts property */
if (of_property_read_u32(np, "interrupts", &at91_gpio->pioc_hwirq)) {
pr_err("at91_gpio.%d, failed to get interrupts property, ignoring.\n",
alias_idx);
goto ioremap_err;
}
/* Get capabilities from compatibility property */
if (of_device_is_compatible(np, "atmel,at91sam9x5-gpio"))
at91_gpio_caps |= AT91_GPIO_CAP_PIO3;
if (!of_property_read_u32(np, "#gpio-lines", &ngpio)) {
if (ngpio >= MAX_NB_GPIO_PER_BANK)
pr_err("at91_gpio.%d, gpio-nb >= %d failback to %d\n",
alias_idx, MAX_NB_GPIO_PER_BANK, MAX_NB_GPIO_PER_BANK);
else
at91_gpio->chip.ngpio = ngpio;
}
/* Setup clock */
if (at91_gpio_setup_clk(alias_idx))
goto ioremap_err;
at91_gpio->chip.of_node = np;
gpio_banks = max(gpio_banks, alias_idx + 1);
at91_gpio->pioc_idx = alias_idx;
return;
ioremap_err:
iounmap(at91_gpio->regbase);
}
static int __init of_at91_gpio_init(void)
{
struct device_node *np = NULL;
/*
* This isn't ideal, but it gets things hooked up until this
* driver is converted into a platform_device
*/
for_each_compatible_node(np, NULL, "atmel,at91rm9200-gpio")
of_at91_gpio_init_one(np);
return gpio_banks > 0 ? 0 : -EINVAL;
}
#else
static int __init of_at91_gpio_init(void)
{
return -EINVAL;
}
#endif
static void __init at91_gpio_init_one(int idx, u32 regbase, int pioc_hwirq)
{
struct at91_gpio_chip *at91_gpio = &gpio_chip[idx];
......@@ -1102,11 +947,11 @@ void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
BUG_ON(nr_banks > MAX_GPIO_BANKS);
if (of_at91_gpio_init() < 0) {
/* No GPIO controller found in device tree */
for (i = 0; i < nr_banks; i++)
at91_gpio_init_one(i, data[i].regbase, data[i].id);
}
if (of_have_populated_dt())
return;
for (i = 0; i < nr_banks; i++)
at91_gpio_init_one(i, data[i].regbase, data[i].id);
for (i = 0; i < gpio_banks; i++) {
at91_gpio = &gpio_chip[i];
......
......@@ -26,6 +26,15 @@ config DEBUG_PINCTRL
help
Say Y here to add some extra checks and diagnostics to PINCTRL calls.
config PINCTRL_AT91
bool "AT91 pinctrl driver"
depends on OF
depends on ARCH_AT91
select PINMUX
select PINCONF
help
Say Y here to enable the at91 pinctrl driver
config PINCTRL_BCM2835
bool
select PINMUX
......
......@@ -9,6 +9,7 @@ ifeq ($(CONFIG_OF),y)
obj-$(CONFIG_PINCTRL) += devicetree.o
endif
obj-$(CONFIG_GENERIC_PINCONF) += pinconf-generic.o
obj-$(CONFIG_PINCTRL_AT91) += pinctrl-at91.o
obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o
obj-$(CONFIG_PINCTRL_IMX) += pinctrl-imx.o
obj-$(CONFIG_PINCTRL_IMX35) += pinctrl-imx35.o
......
此差异已折叠。
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册