提交 5f63517c 编写于 作者: L Linus Torvalds

Merge tag 'pinctrl-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pincontrol fixes from Linus Walleij:
 "A first set of pin control fixes for the v3.15 series:

   - Fix a couple of barnsjukdomar on the Rockchip driver.

   - Remove an idiotic debug print I happened to leave behind in the
     Nomadik driver.

   - Fixup the Qualcomm MSM interrupt handling code for the TLMM v2.

   - Three patches renaming the Broadcom Capri driver to BCM28155.  This
     has been falling between the chairs for some time due to some
     cross-tree synchronization misunderstandings, now I'm fed up with
     this and just rename it in this -rc1 phase"

* tag 'pinctrl-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: fix typo in bindings documentation
  Update bcm_defconfig with new pinctrl CONFIG
  pinctrl: Rename Broadcom Capri pinctrl driver
  pinctrl: msm: Correct interrupt code for TLMM v2
  pinctrl: nomadik: delete stray debug print
  pinctrl: rockchip: handle first half of rk3188-bank0 correctly
  pinctrl: rockchip: add return value to rockchip_set_mux
  pinctrl: rockchip: fix offset of mux registers for rk3188
......@@ -119,7 +119,7 @@ Optional Properties (for HDMI pins):
Example:
// pin controller node
pinctrl@35004800 {
compatible = "brcmbcm11351-pinctrl";
compatible = "brcm,bcm11351-pinctrl";
reg = <0x35004800 0x430>;
// pin configuration node
......
......@@ -132,7 +132,7 @@ CONFIG_CRC_ITU_T=y
CONFIG_CRC7=y
CONFIG_XZ_DEC=y
CONFIG_AVERAGE=y
CONFIG_PINCTRL_CAPRI=y
CONFIG_PINCTRL_BCM281XX=y
CONFIG_WATCHDOG=y
CONFIG_BCM_KONA_WDT=y
CONFIG_BCM_KONA_WDT_DEBUG=y
......@@ -104,16 +104,16 @@ config PINCTRL_BCM2835
select PINMUX
select PINCONF
config PINCTRL_CAPRI
bool "Broadcom Capri pinctrl driver"
config PINCTRL_BCM281XX
bool "Broadcom BCM281xx pinctrl driver"
depends on OF
select PINMUX
select PINCONF
select GENERIC_PINCONF
select REGMAP_MMIO
help
Say Y here to support Broadcom Capri pinctrl driver, which is used for
the BCM281xx SoC family, including BCM11130, BCM11140, BCM11351,
Say Y here to support Broadcom BCM281xx pinctrl driver, which is used
for the BCM281xx SoC family, including BCM11130, BCM11140, BCM11351,
BCM28145, and BCM28155 SoCs. This driver requires the pinctrl
framework. GPIO is provided by a separate GPIO driver.
......
......@@ -21,7 +21,7 @@ obj-$(CONFIG_PINCTRL_BF60x) += pinctrl-adi2-bf60x.o
obj-$(CONFIG_PINCTRL_AT91) += pinctrl-at91.o
obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o
obj-$(CONFIG_PINCTRL_BAYTRAIL) += pinctrl-baytrail.o
obj-$(CONFIG_PINCTRL_CAPRI) += pinctrl-capri.o
obj-$(CONFIG_PINCTRL_BCM281XX) += pinctrl-bcm281xx.o
obj-$(CONFIG_PINCTRL_IMX) += pinctrl-imx.o
obj-$(CONFIG_PINCTRL_IMX1_CORE) += pinctrl-imx1-core.o
obj-$(CONFIG_PINCTRL_IMX27) += pinctrl-imx27.o
......
此差异已折叠。
此差异已折叠。
......@@ -665,7 +665,10 @@ static void msm_gpio_irq_ack(struct irq_data *d)
spin_lock_irqsave(&pctrl->lock, flags);
val = readl(pctrl->regs + g->intr_status_reg);
val &= ~BIT(g->intr_status_bit);
if (g->intr_ack_high)
val |= BIT(g->intr_status_bit);
else
val &= ~BIT(g->intr_status_bit);
writel(val, pctrl->regs + g->intr_status_reg);
if (test_bit(d->hwirq, pctrl->dual_edge_irqs))
......@@ -744,6 +747,7 @@ static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
break;
case IRQ_TYPE_EDGE_BOTH:
val |= BIT(g->intr_detection_bit);
val |= BIT(g->intr_polarity_bit);
break;
case IRQ_TYPE_LEVEL_LOW:
break;
......
......@@ -84,6 +84,7 @@ struct msm_pingroup {
unsigned intr_enable_bit:5;
unsigned intr_status_bit:5;
unsigned intr_ack_high:1;
unsigned intr_target_bit:5;
unsigned intr_raw_status_bit:5;
......
......@@ -877,7 +877,6 @@ static void nmk_gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
struct nmk_gpio_chip *nmk_chip = container_of(chip, struct nmk_gpio_chip, chip);
u32 status;
pr_err("PLONK IRQ %d\n", irq);
clk_enable(nmk_chip->clk);
status = readl(nmk_chip->addr + NMK_GPIO_IS);
clk_disable(nmk_chip->clk);
......
......@@ -342,7 +342,7 @@ static const struct pinctrl_ops rockchip_pctrl_ops = {
* @pin: pin to change
* @mux: new mux function to set
*/
static void rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
static int rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
{
struct rockchip_pinctrl *info = bank->drvdata;
void __iomem *reg = info->reg_base + info->ctrl->mux_offset;
......@@ -350,6 +350,20 @@ static void rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
u8 bit;
u32 data;
/*
* The first 16 pins of rk3188_bank0 are always gpios and do not have
* a mux register at all.
*/
if (bank->bank_type == RK3188_BANK0 && pin < 16) {
if (mux != RK_FUNC_GPIO) {
dev_err(info->dev,
"pin %d only supports a gpio mux\n", pin);
return -ENOTSUPP;
} else {
return 0;
}
}
dev_dbg(info->dev, "setting mux of GPIO%d-%d to %d\n",
bank->bank_num, pin, mux);
......@@ -365,6 +379,8 @@ static void rockchip_set_mux(struct rockchip_pin_bank *bank, int pin, int mux)
writel(data, reg);
spin_unlock_irqrestore(&bank->slock, flags);
return 0;
}
#define RK2928_PULL_OFFSET 0x118
......@@ -560,7 +576,7 @@ static int rockchip_pmx_enable(struct pinctrl_dev *pctldev, unsigned selector,
const unsigned int *pins = info->groups[group].pins;
const struct rockchip_pin_config *data = info->groups[group].data;
struct rockchip_pin_bank *bank;
int cnt;
int cnt, ret = 0;
dev_dbg(info->dev, "enable function %s group %s\n",
info->functions[selector].name, info->groups[group].name);
......@@ -571,8 +587,18 @@ static int rockchip_pmx_enable(struct pinctrl_dev *pctldev, unsigned selector,
*/
for (cnt = 0; cnt < info->groups[group].npins; cnt++) {
bank = pin_to_bank(info, pins[cnt]);
rockchip_set_mux(bank, pins[cnt] - bank->pin_base,
data[cnt].func);
ret = rockchip_set_mux(bank, pins[cnt] - bank->pin_base,
data[cnt].func);
if (ret)
break;
}
if (ret) {
/* revert the already done pin settings */
for (cnt--; cnt >= 0; cnt--)
rockchip_set_mux(bank, pins[cnt] - bank->pin_base, 0);
return ret;
}
return 0;
......@@ -607,7 +633,7 @@ static int rockchip_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
struct rockchip_pinctrl *info = pinctrl_dev_get_drvdata(pctldev);
struct rockchip_pin_bank *bank;
struct gpio_chip *chip;
int pin;
int pin, ret;
u32 data;
chip = range->gc;
......@@ -617,7 +643,9 @@ static int rockchip_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
dev_dbg(info->dev, "gpio_direction for pin %u as %s-%d to %s\n",
offset, range->name, pin, input ? "input" : "output");
rockchip_set_mux(bank, pin, RK_FUNC_GPIO);
ret = rockchip_set_mux(bank, pin, RK_FUNC_GPIO);
if (ret < 0)
return ret;
data = readl_relaxed(bank->reg_base + GPIO_SWPORT_DDR);
/* set bit to 1 for output, 0 for input */
......@@ -1144,9 +1172,13 @@ static int rockchip_irq_set_type(struct irq_data *d, unsigned int type)
u32 polarity;
u32 level;
u32 data;
int ret;
/* make sure the pin is configured as gpio input */
rockchip_set_mux(bank, d->hwirq, RK_FUNC_GPIO);
ret = rockchip_set_mux(bank, d->hwirq, RK_FUNC_GPIO);
if (ret < 0)
return ret;
data = readl_relaxed(bank->reg_base + GPIO_SWPORT_DDR);
data &= ~mask;
writel_relaxed(data, bank->reg_base + GPIO_SWPORT_DDR);
......@@ -1534,7 +1566,7 @@ static struct rockchip_pin_ctrl rk3188_pin_ctrl = {
.nr_banks = ARRAY_SIZE(rk3188_pin_banks),
.label = "RK3188-GPIO",
.type = RK3188,
.mux_offset = 0x68,
.mux_offset = 0x60,
.pull_calc_reg = rk3188_calc_pull_reg_and_bit,
};
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册