提交 5cff20e6 编写于 作者: J Johannes Berg 提交者: John W. Linville

mac80211: tell driver when idle

When we aren't doing anything in mac80211, we can turn off
much of the hardware, depending on the driver/hw. Not doing
anything, aka being idle, means:

 * no monitor interfaces
 * no AP/mesh/wds interfaces
 * any station interfaces are in DISABLED state
 * any IBSS interfaces aren't trying to be in a network
 * we aren't trying to scan

By creating a new function that verifies these conditions and calling
it at strategic points where the states of those conditions change,
we can easily make mac80211 tell the driver when we are idle to save
power.

Additionally, this fixes a small quirk where a recalculated powersave
state is passed to the driver even if the hardware is about to stopped
completely.

This patch intentionally doesn't touch radio_enabled because that is
currently implemented to be a soft rfkill which is inappropriate here
when we need to be able to wake up with low latency.

One thing I'm not entirely sure about is this:

  phy0: device no longer idle - in use
  wlan0: direct probe to AP 00:11:24:91:07:4d try 1
  wlan0 direct probe responded
  wlan0: authenticate with AP 00:11:24:91:07:4d
  wlan0: authenticated
> phy0: device now idle
> phy0: device no longer idle - in use
  wlan0: associate with AP 00:11:24:91:07:4d
  wlan0: RX AssocResp from 00:11:24:91:07:4d (capab=0x401 status=0 aid=1)
  wlan0: associated

Is it appropriate to go into idle state for a short time when we have
just authenticated, but not associated yet? This happens only with the
userspace SME, because we cannot really know how long it will wait
before asking us to associate. Would going idle after a short timeout
be more appropriate? We may need to revisit this, depending on what
happens.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
上级 9955151d
......@@ -553,9 +553,11 @@ static int mac80211_hwsim_config(struct ieee80211_hw *hw, u32 changed)
struct mac80211_hwsim_data *data = hw->priv;
struct ieee80211_conf *conf = &hw->conf;
printk(KERN_DEBUG "%s:%s (freq=%d radio_enabled=%d)\n",
printk(KERN_DEBUG "%s:%s (freq=%d radio_enabled=%d idle=%d ps=%d)\n",
wiphy_name(hw->wiphy), __func__,
conf->channel->center_freq, conf->radio_enabled);
conf->channel->center_freq, conf->radio_enabled,
!!(conf->flags & IEEE80211_CONF_IDLE),
!!(conf->flags & IEEE80211_CONF_PS));
data->channel = conf->channel;
data->radio_enabled = conf->radio_enabled;
......
......@@ -533,10 +533,16 @@ struct ieee80211_rx_status {
*
* @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported)
* @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only)
* @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
* the driver should be prepared to handle configuration requests but
* may turn the device off as much as possible. Typically, this flag will
* be set when an interface is set UP but not associated or scanning, but
* it can also be unset in that case when monitor interfaces are active.
*/
enum ieee80211_conf_flags {
IEEE80211_CONF_RADIOTAP = (1<<0),
IEEE80211_CONF_PS = (1<<1),
IEEE80211_CONF_IDLE = (1<<2),
};
......@@ -551,6 +557,7 @@ enum ieee80211_conf_flags {
* @IEEE80211_CONF_CHANGE_POWER: the TX power changed
* @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
* @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
* @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
*/
enum ieee80211_conf_changed {
IEEE80211_CONF_CHANGE_RADIO_ENABLED = BIT(0),
......@@ -561,6 +568,7 @@ enum ieee80211_conf_changed {
IEEE80211_CONF_CHANGE_POWER = BIT(5),
IEEE80211_CONF_CHANGE_CHANNEL = BIT(6),
IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7),
IEEE80211_CONF_CHANGE_IDLE = BIT(8),
};
static inline __deprecated enum ieee80211_conf_changed
......
......@@ -862,6 +862,8 @@ int ieee80211_ibss_join(struct ieee80211_sub_if_data *sdata,
sdata->u.ibss.ssid_len = params->ssid_len;
ieee80211_recalc_idle(sdata->local);
set_bit(IEEE80211_IBSS_REQ_RUN, &sdata->u.ibss.request);
queue_work(sdata->local->hw.workqueue, &sdata->u.ibss.work);
......@@ -889,6 +891,9 @@ int ieee80211_ibss_leave(struct ieee80211_sub_if_data *sdata)
skb_queue_purge(&sdata->u.ibss.skb_queue);
memset(sdata->u.ibss.bssid, 0, ETH_ALEN);
sdata->u.ibss.ssid_len = 0;
ieee80211_recalc_idle(sdata->local);
return 0;
}
......@@ -985,6 +985,8 @@ int ieee80211_if_change_type(struct ieee80211_sub_if_data *sdata,
enum nl80211_iftype type);
void ieee80211_if_remove(struct ieee80211_sub_if_data *sdata);
void ieee80211_remove_interfaces(struct ieee80211_local *local);
u32 __ieee80211_recalc_idle(struct ieee80211_local *local);
void ieee80211_recalc_idle(struct ieee80211_local *local);
/* tx handling */
void ieee80211_clear_tx_pending(struct ieee80211_local *local);
......
......@@ -301,6 +301,8 @@ static int ieee80211_open(struct net_device *dev)
if (sdata->flags & IEEE80211_SDATA_PROMISC)
atomic_inc(&local->iff_promiscs);
hw_reconf_flags |= __ieee80211_recalc_idle(local);
local->open_count++;
if (hw_reconf_flags) {
ieee80211_hw_config(local, hw_reconf_flags);
......@@ -548,6 +550,10 @@ static int ieee80211_stop(struct net_device *dev)
sdata->bss = NULL;
hw_reconf_flags |= __ieee80211_recalc_idle(local);
ieee80211_recalc_ps(local, -1);
if (local->open_count == 0) {
if (netif_running(local->mdev))
dev_close(local->mdev);
......@@ -565,8 +571,6 @@ static int ieee80211_stop(struct net_device *dev)
hw_reconf_flags = 0;
}
ieee80211_recalc_ps(local, -1);
/* do after stop to avoid reconfiguring when we stop anyway */
if (hw_reconf_flags)
ieee80211_hw_config(local, hw_reconf_flags);
......@@ -892,3 +896,73 @@ void ieee80211_remove_interfaces(struct ieee80211_local *local)
unregister_netdevice(sdata->dev);
}
}
static u32 ieee80211_idle_off(struct ieee80211_local *local,
const char *reason)
{
if (!(local->hw.conf.flags & IEEE80211_CONF_IDLE))
return 0;
#ifdef CONFIG_MAC80211_VERBOSE_DEBUG
printk(KERN_DEBUG "%s: device no longer idle - %s\n",
wiphy_name(local->hw.wiphy), reason);
#endif
local->hw.conf.flags &= ~IEEE80211_CONF_IDLE;
return IEEE80211_CONF_CHANGE_IDLE;
}
static u32 ieee80211_idle_on(struct ieee80211_local *local)
{
if (local->hw.conf.flags & IEEE80211_CONF_IDLE)
return 0;
#ifdef CONFIG_MAC80211_VERBOSE_DEBUG
printk(KERN_DEBUG "%s: device now idle\n",
wiphy_name(local->hw.wiphy));
#endif
local->hw.conf.flags |= IEEE80211_CONF_IDLE;
return IEEE80211_CONF_CHANGE_IDLE;
}
u32 __ieee80211_recalc_idle(struct ieee80211_local *local)
{
struct ieee80211_sub_if_data *sdata;
int count = 0;
if (local->hw_scanning || local->sw_scanning)
return ieee80211_idle_off(local, "scanning");
list_for_each_entry(sdata, &local->interfaces, list) {
if (!netif_running(sdata->dev))
continue;
/* do not count disabled managed interfaces */
if (sdata->vif.type == NL80211_IFTYPE_STATION &&
sdata->u.mgd.state == IEEE80211_STA_MLME_DISABLED)
continue;
/* do not count unused IBSS interfaces */
if (sdata->vif.type == NL80211_IFTYPE_ADHOC &&
!sdata->u.ibss.ssid_len)
continue;
/* count everything else */
count++;
}
if (!count)
return ieee80211_idle_on(local);
else
return ieee80211_idle_off(local, "in use");
return 0;
}
void ieee80211_recalc_idle(struct ieee80211_local *local)
{
u32 chg;
mutex_lock(&local->iflist_mtx);
chg = __ieee80211_recalc_idle(local);
mutex_unlock(&local->iflist_mtx);
ieee80211_hw_config(local, chg);
}
......@@ -890,6 +890,7 @@ static void ieee80211_direct_probe(struct ieee80211_sub_if_data *sdata)
printk(KERN_DEBUG "%s: direct probe to AP %pM timed out\n",
sdata->dev->name, ifmgd->bssid);
ifmgd->state = IEEE80211_STA_MLME_DISABLED;
ieee80211_recalc_idle(local);
cfg80211_send_auth_timeout(sdata->dev, ifmgd->bssid);
/*
......@@ -938,6 +939,7 @@ static void ieee80211_authenticate(struct ieee80211_sub_if_data *sdata)
" timed out\n",
sdata->dev->name, ifmgd->bssid);
ifmgd->state = IEEE80211_STA_MLME_DISABLED;
ieee80211_recalc_idle(local);
cfg80211_send_auth_timeout(sdata->dev, ifmgd->bssid);
ieee80211_rx_bss_remove(sdata, ifmgd->bssid,
sdata->local->hw.conf.channel->center_freq,
......@@ -1041,6 +1043,8 @@ static void ieee80211_set_disassoc(struct ieee80211_sub_if_data *sdata,
rcu_read_unlock();
ieee80211_recalc_idle(local);
/* channel(_type) changes are handled by ieee80211_hw_config */
local->oper_channel_type = NL80211_CHAN_NO_HT;
......@@ -1121,6 +1125,7 @@ static void ieee80211_associate(struct ieee80211_sub_if_data *sdata)
" timed out\n",
sdata->dev->name, ifmgd->bssid);
ifmgd->state = IEEE80211_STA_MLME_DISABLED;
ieee80211_recalc_idle(local);
cfg80211_send_assoc_timeout(sdata->dev, ifmgd->bssid);
ieee80211_rx_bss_remove(sdata, ifmgd->bssid,
sdata->local->hw.conf.channel->center_freq,
......@@ -1141,6 +1146,7 @@ static void ieee80211_associate(struct ieee80211_sub_if_data *sdata)
printk(KERN_DEBUG "%s: mismatch in privacy configuration and "
"mixed-cell disabled - abort association\n", sdata->dev->name);
ifmgd->state = IEEE80211_STA_MLME_DISABLED;
ieee80211_recalc_idle(local);
return;
}
......@@ -1279,6 +1285,7 @@ static void ieee80211_auth_completed(struct ieee80211_sub_if_data *sdata)
if (ifmgd->flags & IEEE80211_STA_EXT_SME) {
/* Wait for SME to request association */
ifmgd->state = IEEE80211_STA_MLME_DISABLED;
ieee80211_recalc_idle(sdata->local);
} else
ieee80211_associate(sdata);
}
......@@ -1515,6 +1522,7 @@ static void ieee80211_rx_mgmt_assoc_resp(struct ieee80211_sub_if_data *sdata,
if (ifmgd->flags & IEEE80211_STA_EXT_SME) {
/* Wait for SME to decide what to do next */
ifmgd->state = IEEE80211_STA_MLME_DISABLED;
ieee80211_recalc_idle(local);
}
return;
}
......@@ -2083,6 +2091,7 @@ static int ieee80211_sta_config_auth(struct ieee80211_sub_if_data *sdata)
} else {
ifmgd->assoc_scan_tries = 0;
ifmgd->state = IEEE80211_STA_MLME_DISABLED;
ieee80211_recalc_idle(local);
}
}
return -1;
......@@ -2126,6 +2135,8 @@ static void ieee80211_sta_work(struct work_struct *work)
} else if (!test_and_clear_bit(IEEE80211_STA_REQ_RUN, &ifmgd->request))
return;
ieee80211_recalc_idle(local);
switch (ifmgd->state) {
case IEEE80211_STA_MLME_DISABLED:
break;
......
......@@ -302,17 +302,9 @@ void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted)
/* we only have to protect scan_req and hw/sw scan */
mutex_unlock(&local->scan_mtx);
if (was_hw_scan) {
/*
* Somebody might have requested channel change during scan
* that we won't have acted upon, try now. ieee80211_hw_config
* will set the flag based on actual changes.
*/
ieee80211_hw_config(local, 0);
goto done;
}
ieee80211_hw_config(local, IEEE80211_CONF_CHANGE_CHANNEL);
if (was_hw_scan)
goto done;
netif_tx_lock_bh(local->mdev);
netif_addr_lock(local->mdev);
......@@ -351,6 +343,7 @@ void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted)
mutex_unlock(&local->iflist_mtx);
done:
ieee80211_recalc_idle(local);
ieee80211_mlme_notify_scan_completed(local);
ieee80211_ibss_notify_scan_completed(local);
ieee80211_mesh_notify_scan_completed(local);
......@@ -471,6 +464,8 @@ static int __ieee80211_start_scan(struct ieee80211_sub_if_data *sdata,
* dependency, so that the scan completed calls
* have more locking freedom.
*/
ieee80211_recalc_idle(local);
mutex_unlock(&local->scan_mtx);
if (local->ops->hw_scan)
......@@ -487,6 +482,8 @@ static int __ieee80211_start_scan(struct ieee80211_sub_if_data *sdata,
} else
local->sw_scanning = false;
ieee80211_recalc_idle(local);
local->scan_req = NULL;
local->scan_sdata = NULL;
}
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册