提交 56d4b8a2 编写于 作者: M Mika Westerberg 提交者: Wolfram Sang

i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348

ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:

  i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
  i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
  i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
  i2c_designware INT3433:00: controller timed out

The values received from ACPI are (in fast mode):

  HCNT: 72
  LCNT: 160

this translates to following timings (input clock is 100MHz on Broadwell):

  tHIGH: 720 ns (spec min 600 ns)
  tLOW: 1600 ns (spec min 1300 ns)
  Bus period: 2920 ns (assuming 300 ns tf and tr)
  Bus speed: 342.5 kHz

Both tHIGH and tLOW are within the I2C specification.

The calculated values when ACPI parameters are not used are (in fast mode):

  HCNT: 87
  LCNT: 159

which translates to:

  tHIGH: 870 ns (spec min 600 ns)
  tLOW: 1590 ns (spec min 1300 ns)
  Bus period 3060 ns (assuming 300 ns tf and tr)
  Bus speed 326.8 kHz

These values are also within the I2C specification.

Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).

Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: NPavel Roskin <plroskin@gmail.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: NPavel Roskin <plroskin@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
上级 fc531d98
......@@ -24,6 +24,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/dmi.h>
#include <linux/i2c.h>
#include <linux/clk.h>
#include <linux/clk-provider.h>
......@@ -51,6 +52,22 @@ static u32 i2c_dw_get_clk_rate_khz(struct dw_i2c_dev *dev)
}
#ifdef CONFIG_ACPI
/*
* The HCNT/LCNT information coming from ACPI should be the most accurate
* for given platform. However, some systems get it wrong. On such systems
* we get better results by calculating those based on the input clock.
*/
static const struct dmi_system_id dw_i2c_no_acpi_params[] = {
{
.ident = "Dell Inspiron 7348",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
DMI_MATCH(DMI_PRODUCT_NAME, "Inspiron 7348"),
},
},
{ }
};
static void dw_i2c_acpi_params(struct platform_device *pdev, char method[],
u16 *hcnt, u16 *lcnt, u32 *sda_hold)
{
......@@ -58,6 +75,9 @@ static void dw_i2c_acpi_params(struct platform_device *pdev, char method[],
acpi_handle handle = ACPI_HANDLE(&pdev->dev);
union acpi_object *obj;
if (dmi_check_system(dw_i2c_no_acpi_params))
return;
if (ACPI_FAILURE(acpi_evaluate_object(handle, method, NULL, &buf)))
return;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册