提交 40ac81a3 编写于 作者: B Ben Cahill 提交者: David S. Miller

iwl-4965-hw.h: clean up unused eeprom structures and definitions

Clean up unused eeprom structures and definitions in iwl-4965-hw.h.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
上级 796083cb
......@@ -169,57 +169,6 @@ struct iwl4965_eeprom_channel {
s8 max_power_avg; /* max power (dBm) on this chnl, limit 31 */
} __attribute__ ((packed));
/*
* Mapping of a Tx power level, at factory calibration temperature,
* to a radio/DSP gain table index.
* One for each of 5 "sample" power levels in each band.
* v_det is measured at the factory, using the 3945's built-in power amplifier
* (PA) output voltage detector. This same detector is used during Tx of
* long packets in normal operation to provide feedback as to proper output
* level.
* Data copied from EEPROM.
*/
struct iwl4965_eeprom_txpower_sample {
u8 gain_index; /* index into power (gain) setup table ... */
s8 power; /* ... for this pwr level for this chnl group */
u16 v_det; /* PA output voltage */
} __attribute__ ((packed));
/*
* Mappings of Tx power levels -> nominal radio/DSP gain table indexes.
* One for each channel group (a.k.a. "band") (1 for BG, 4 for A).
* Tx power setup code interpolates between the 5 "sample" power levels
* to determine the nominal setup for a requested power level.
* Data copied from EEPROM.
* DO NOT ALTER THIS STRUCTURE!!!
*/
struct iwl4965_eeprom_txpower_group {
struct iwl4965_eeprom_txpower_sample samples[5]; /* 5 power levels */
s32 a, b, c, d, e; /* coefficients for voltage->power
* formula (signed) */
s32 Fa, Fb, Fc, Fd, Fe; /* these modify coeffs based on
* frequency (signed) */
s8 saturation_power; /* highest power possible by h/w in this
* band */
u8 group_channel; /* "representative" channel # in this band */
s16 temperature; /* h/w temperature at factory calib this band
* (signed) */
} __attribute__ ((packed));
/*
* Temperature-based Tx-power compensation data, not band-specific.
* These coefficients are use to modify a/b/c/d/e coeffs based on
* difference between current temperature and factory calib temperature.
* Data copied from EEPROM.
*/
struct iwl4965_eeprom_temperature_corr {
u32 Ta;
u32 Tb;
u32 Tc;
u32 Td;
u32 Te;
} __attribute__ ((packed));
/* 4965 has two radio transmitters (and 3 radio receivers) */
#define EEPROM_TX_POWER_TX_CHAINS (2)
......@@ -230,8 +179,6 @@ struct iwl4965_eeprom_temperature_corr {
* each of 3 target output levels */
#define EEPROM_TX_POWER_MEASUREMENTS (3)
#define EEPROM_TX_POWER_VERSION (2)
/* 4965 driver does not work with txpower calibration version < 5.
* Look for this in calib_version member of struct iwl4965_eeprom. */
#define EEPROM_TX_POWER_VERSION_NEW (5)
......@@ -461,10 +408,7 @@ struct iwl4965_eeprom {
#define EEPROM_CALIB_VERSION_OFFSET (2*0xB6) /* 2 bytes */
u16 calib_version; /* abs.ofs: 364 */
u8 reserved13[2];
#define EEPROM_SATURATION_POWER_OFFSET (2*0xB8) /* 2 bytes */
u16 satruation_power; /* abs.ofs: 368 */
u8 reserved14[94];
u8 reserved14[96]; /* abs.ofs: 368 */
/*
* 4965 Txpower calibration data.
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册