提交 259b83a3 编写于 作者: H Hauke Mehrtens 提交者: Greg Kroah-Hartman

USB: OHCI: remove old SSB OHCI driver

This is now replaced by the new ssb USB driver, which also supports
devices with an EHCI controller.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
上级 7043c2cc
......@@ -373,10 +373,15 @@ config USB_OHCI_HCD_PCI
If unsure, say Y.
config USB_OHCI_HCD_SSB
bool "OHCI support for Broadcom SSB OHCI core"
bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)"
depends on USB_OHCI_HCD && (SSB = y || SSB = USB_OHCI_HCD) && EXPERIMENTAL
select USB_HCD_SSB
select USB_OHCI_HCD_PLATFORM
default n
---help---
This option is deprecated now and the driver was removed, use
USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead.
Support for the Sonics Silicon Backplane (SSB) attached
Broadcom USB OHCI core.
......
......@@ -1080,11 +1080,6 @@ MODULE_LICENSE ("GPL");
#define PS3_SYSTEM_BUS_DRIVER ps3_ohci_driver
#endif
#ifdef CONFIG_USB_OHCI_HCD_SSB
#include "ohci-ssb.c"
#define SSB_OHCI_DRIVER ssb_ohci_driver
#endif
#ifdef CONFIG_MFD_SM501
#include "ohci-sm501.c"
#define SM501_OHCI_DRIVER ohci_hcd_sm501_driver
......@@ -1128,8 +1123,7 @@ MODULE_LICENSE ("GPL");
!defined(SA1111_DRIVER) && \
!defined(PS3_SYSTEM_BUS_DRIVER) && \
!defined(SM501_OHCI_DRIVER) && \
!defined(TMIO_OHCI_DRIVER) && \
!defined(SSB_OHCI_DRIVER)
!defined(TMIO_OHCI_DRIVER)
#error "missing bus glue for ohci-hcd"
#endif
......@@ -1195,12 +1189,6 @@ static int __init ohci_hcd_mod_init(void)
goto error_pci;
#endif
#ifdef SSB_OHCI_DRIVER
retval = ssb_driver_register(&SSB_OHCI_DRIVER);
if (retval)
goto error_ssb;
#endif
#ifdef SM501_OHCI_DRIVER
retval = platform_driver_register(&SM501_OHCI_DRIVER);
if (retval < 0)
......@@ -1224,10 +1212,6 @@ static int __init ohci_hcd_mod_init(void)
platform_driver_unregister(&SM501_OHCI_DRIVER);
error_sm501:
#endif
#ifdef SSB_OHCI_DRIVER
ssb_driver_unregister(&SSB_OHCI_DRIVER);
error_ssb:
#endif
#ifdef PCI_DRIVER
pci_unregister_driver(&PCI_DRIVER);
error_pci:
......@@ -1275,9 +1259,6 @@ static void __exit ohci_hcd_mod_exit(void)
#ifdef SM501_OHCI_DRIVER
platform_driver_unregister(&SM501_OHCI_DRIVER);
#endif
#ifdef SSB_OHCI_DRIVER
ssb_driver_unregister(&SSB_OHCI_DRIVER);
#endif
#ifdef PCI_DRIVER
pci_unregister_driver(&PCI_DRIVER);
#endif
......
/*
* Sonics Silicon Backplane
* Broadcom USB-core OHCI driver
*
* Copyright 2007 Michael Buesch <m@bues.ch>
*
* Derived from the OHCI-PCI driver
* Copyright 1999 Roman Weissgaerber
* Copyright 2000-2002 David Brownell
* Copyright 1999 Linus Torvalds
* Copyright 1999 Gregory P. Smith
*
* Derived from the USBcore related parts of Broadcom-SB
* Copyright 2005 Broadcom Corporation
*
* Licensed under the GNU/GPL. See COPYING for details.
*/
#include <linux/ssb/ssb.h>
#define SSB_OHCI_TMSLOW_HOSTMODE (1 << 29)
struct ssb_ohci_device {
struct ohci_hcd ohci; /* _must_ be at the beginning. */
u32 enable_flags;
};
static inline
struct ssb_ohci_device *hcd_to_ssb_ohci(struct usb_hcd *hcd)
{
return (struct ssb_ohci_device *)(hcd->hcd_priv);
}
static int ssb_ohci_reset(struct usb_hcd *hcd)
{
struct ssb_ohci_device *ohcidev = hcd_to_ssb_ohci(hcd);
struct ohci_hcd *ohci = &ohcidev->ohci;
int err;
ohci_hcd_init(ohci);
err = ohci_init(ohci);
return err;
}
static int ssb_ohci_start(struct usb_hcd *hcd)
{
struct ssb_ohci_device *ohcidev = hcd_to_ssb_ohci(hcd);
struct ohci_hcd *ohci = &ohcidev->ohci;
int err;
err = ohci_run(ohci);
if (err < 0) {
ohci_err(ohci, "can't start\n");
ohci_stop(hcd);
}
return err;
}
static const struct hc_driver ssb_ohci_hc_driver = {
.description = "ssb-usb-ohci",
.product_desc = "SSB OHCI Controller",
.hcd_priv_size = sizeof(struct ssb_ohci_device),
.irq = ohci_irq,
.flags = HCD_MEMORY | HCD_USB11,
.reset = ssb_ohci_reset,
.start = ssb_ohci_start,
.stop = ohci_stop,
.shutdown = ohci_shutdown,
.urb_enqueue = ohci_urb_enqueue,
.urb_dequeue = ohci_urb_dequeue,
.endpoint_disable = ohci_endpoint_disable,
.get_frame_number = ohci_get_frame,
.hub_status_data = ohci_hub_status_data,
.hub_control = ohci_hub_control,
#ifdef CONFIG_PM
.bus_suspend = ohci_bus_suspend,
.bus_resume = ohci_bus_resume,
#endif
.start_port_reset = ohci_start_port_reset,
};
static void ssb_ohci_detach(struct ssb_device *dev)
{
struct usb_hcd *hcd = ssb_get_drvdata(dev);
if (hcd->driver->shutdown)
hcd->driver->shutdown(hcd);
usb_remove_hcd(hcd);
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
ssb_device_disable(dev, 0);
}
static int ssb_ohci_attach(struct ssb_device *dev)
{
struct ssb_ohci_device *ohcidev;
struct usb_hcd *hcd;
int err = -ENOMEM;
u32 tmp, flags = 0;
if (dma_set_mask(dev->dma_dev, DMA_BIT_MASK(32)) ||
dma_set_coherent_mask(dev->dma_dev, DMA_BIT_MASK(32)))
return -EOPNOTSUPP;
if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV) {
/* Put the device into host-mode. */
flags |= SSB_OHCI_TMSLOW_HOSTMODE;
ssb_device_enable(dev, flags);
} else if (dev->id.coreid == SSB_DEV_USB20_HOST) {
/*
* USB 2.0 special considerations:
*
* In addition to the standard SSB reset sequence, the Host
* Control Register must be programmed to bring the USB core
* and various phy components out of reset.
*/
ssb_device_enable(dev, 0);
ssb_write32(dev, 0x200, 0x7ff);
/* Change Flush control reg */
tmp = ssb_read32(dev, 0x400);
tmp &= ~8;
ssb_write32(dev, 0x400, tmp);
tmp = ssb_read32(dev, 0x400);
/* Change Shim control reg */
tmp = ssb_read32(dev, 0x304);
tmp &= ~0x100;
ssb_write32(dev, 0x304, tmp);
tmp = ssb_read32(dev, 0x304);
udelay(1);
/* Work around for 5354 failures */
if (dev->id.revision == 2 && dev->bus->chip_id == 0x5354) {
/* Change syn01 reg */
tmp = 0x00fe00fe;
ssb_write32(dev, 0x894, tmp);
/* Change syn03 reg */
tmp = ssb_read32(dev, 0x89c);
tmp |= 0x1;
ssb_write32(dev, 0x89c, tmp);
}
} else
ssb_device_enable(dev, 0);
hcd = usb_create_hcd(&ssb_ohci_hc_driver, dev->dev,
dev_name(dev->dev));
if (!hcd)
goto err_dev_disable;
ohcidev = hcd_to_ssb_ohci(hcd);
ohcidev->enable_flags = flags;
tmp = ssb_read32(dev, SSB_ADMATCH0);
hcd->rsrc_start = ssb_admatch_base(tmp);
hcd->rsrc_len = ssb_admatch_size(tmp);
hcd->regs = ioremap_nocache(hcd->rsrc_start, hcd->rsrc_len);
if (!hcd->regs)
goto err_put_hcd;
err = usb_add_hcd(hcd, dev->irq, IRQF_SHARED);
if (err)
goto err_iounmap;
ssb_set_drvdata(dev, hcd);
return err;
err_iounmap:
iounmap(hcd->regs);
err_put_hcd:
usb_put_hcd(hcd);
err_dev_disable:
ssb_device_disable(dev, flags);
return err;
}
static int ssb_ohci_probe(struct ssb_device *dev,
const struct ssb_device_id *id)
{
int err;
u16 chipid_top;
/* USBcores are only connected on embedded devices. */
chipid_top = (dev->bus->chip_id & 0xFF00);
if (chipid_top != 0x4700 && chipid_top != 0x5300)
return -ENODEV;
/* TODO: Probably need checks here; is the core connected? */
if (usb_disabled())
return -ENODEV;
/* We currently always attach SSB_DEV_USB11_HOSTDEV
* as HOST OHCI. If we want to attach it as Client device,
* we must branch here and call into the (yet to
* be written) Client mode driver. Same for remove(). */
err = ssb_ohci_attach(dev);
return err;
}
static void ssb_ohci_remove(struct ssb_device *dev)
{
ssb_ohci_detach(dev);
}
#ifdef CONFIG_PM
static int ssb_ohci_suspend(struct ssb_device *dev, pm_message_t state)
{
ssb_device_disable(dev, 0);
return 0;
}
static int ssb_ohci_resume(struct ssb_device *dev)
{
struct usb_hcd *hcd = ssb_get_drvdata(dev);
struct ssb_ohci_device *ohcidev = hcd_to_ssb_ohci(hcd);
ssb_device_enable(dev, ohcidev->enable_flags);
ohci_finish_controller_resume(hcd);
return 0;
}
#else /* !CONFIG_PM */
#define ssb_ohci_suspend NULL
#define ssb_ohci_resume NULL
#endif /* CONFIG_PM */
static const struct ssb_device_id ssb_ohci_table[] = {
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOSTDEV, SSB_ANY_REV),
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOST, SSB_ANY_REV),
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB20_HOST, SSB_ANY_REV),
SSB_DEVTABLE_END
};
MODULE_DEVICE_TABLE(ssb, ssb_ohci_table);
static struct ssb_driver ssb_ohci_driver = {
.name = KBUILD_MODNAME,
.id_table = ssb_ohci_table,
.probe = ssb_ohci_probe,
.remove = ssb_ohci_remove,
.suspend = ssb_ohci_suspend,
.resume = ssb_ohci_resume,
};
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册