提交 24c1a280 编写于 作者: L Luis R. Rodriguez 提交者: John W. Linville

ath9k: add comments for ath9k_hw_configpcipowersave()

This is used for ASPM.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
上级 a89d03c4
......@@ -2632,6 +2632,15 @@ bool ath9k_hw_setpower(struct ath_hw *ah, enum ath9k_power_mode mode)
return status;
}
/*
* Helper for ASPM support.
*
* Disable PLL when in L0s as well as receiver clock when in L1.
* This power saving option must be enabled through the SerDes.
*
* Programming the SerDes must go through the same 288 bit serial shift
* register as the other analog registers. Hence the 9 writes.
*/
void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore)
{
u8 i;
......@@ -2639,13 +2648,20 @@ void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore)
if (ah->is_pciexpress != true)
return;
/* Do not touch SerDes registers */
if (ah->config.pcie_powersave_enable == 2)
return;
/* Nothing to do on restore for 11N */
if (restore)
return;
if (AR_SREV_9280_20_OR_LATER(ah)) {
/*
* AR9280 2.0 or later chips use SerDes values from the
* initvals.h initialized depending on chipset during
* ath9k_hw_do_attach()
*/
for (i = 0; i < ah->iniPcieSerdes.ia_rows; i++) {
REG_WRITE(ah, INI_RA(&ah->iniPcieSerdes, i, 0),
INI_RA(&ah->iniPcieSerdes, i, 1));
......@@ -2656,10 +2672,12 @@ void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore)
REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fd00);
REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
/* RX shut off when elecidle is asserted */
REG_WRITE(ah, AR_PCIE_SERDES, 0xa8000019);
REG_WRITE(ah, AR_PCIE_SERDES, 0x13160820);
REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980560);
/* Shut off CLKREQ active in L1 */
if (ah->config.pcie_clock_req)
REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffc);
else
......@@ -2669,29 +2687,46 @@ void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore)
REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
REG_WRITE(ah, AR_PCIE_SERDES, 0x00043007);
/* Load the new settings */
REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
udelay(1000);
} else {
REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fc00);
REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
/* RX shut off when elecidle is asserted */
REG_WRITE(ah, AR_PCIE_SERDES, 0x28000039);
REG_WRITE(ah, AR_PCIE_SERDES, 0x53160824);
REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980579);
/*
* Ignore ah->ah_config.pcie_clock_req setting for
* pre-AR9280 11n
*/
REG_WRITE(ah, AR_PCIE_SERDES, 0x001defff);
REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
REG_WRITE(ah, AR_PCIE_SERDES, 0x000e3007);
/* Load the new settings */
REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
}
/* set bit 19 to allow forcing of pcie core into L1 state */
REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
/* Several PCIe massages to ensure proper behaviour */
if (ah->config.pcie_waen) {
REG_WRITE(ah, AR_WA, ah->config.pcie_waen);
} else {
if (AR_SREV_9285(ah))
REG_WRITE(ah, AR_WA, AR9285_WA_DEFAULT);
/*
* On AR9280 chips bit 22 of 0x4004 needs to be set to
* otherwise card may disappear.
*/
else if (AR_SREV_9280(ah))
REG_WRITE(ah, AR_WA, AR9280_WA_DEFAULT);
else
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册