提交 17497acb 编写于 作者: T Tejun Heo

blk-mq, percpu_ref: start q->mq_usage_counter in atomic mode

blk-mq uses percpu_ref for its usage counter which tracks the number
of in-flight commands and used to synchronously drain the queue on
freeze.  percpu_ref shutdown takes measureable wallclock time as it
involves a sched RCU grace period.  This means that draining a blk-mq
takes measureable wallclock time.  One would think that this shouldn't
matter as queue shutdown should be a rare event which takes place
asynchronously w.r.t. userland.

Unfortunately, SCSI probing involves synchronously setting up and then
tearing down a lot of request_queues back-to-back for non-existent
LUNs.  This means that SCSI probing may take above ten seconds when
scsi-mq is used.

  [    0.949892] scsi host0: Virtio SCSI HBA
  [    1.007864] scsi 0:0:0:0: Direct-Access     QEMU     QEMU HARDDISK    1.1. PQ: 0 ANSI: 5
  [    1.021299] scsi 0:0:1:0: Direct-Access     QEMU     QEMU HARDDISK    1.1. PQ: 0 ANSI: 5
  [    1.520356] tsc: Refined TSC clocksource calibration: 2491.910 MHz

  <stall>

  [   16.186549] sd 0:0:0:0: Attached scsi generic sg0 type 0
  [   16.190478] sd 0:0:1:0: Attached scsi generic sg1 type 0
  [   16.194099] osd: LOADED open-osd 0.2.1
  [   16.203202] sd 0:0:0:0: [sda] 31457280 512-byte logical blocks: (16.1 GB/15.0 GiB)
  [   16.208478] sd 0:0:0:0: [sda] Write Protect is off
  [   16.211439] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
  [   16.218771] sd 0:0:1:0: [sdb] 31457280 512-byte logical blocks: (16.1 GB/15.0 GiB)
  [   16.223264] sd 0:0:1:0: [sdb] Write Protect is off
  [   16.225682] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

This is also the reason why request_queues start in bypass mode which
is ended on blk_register_queue() as shutting down a fully functional
queue also involves a RCU grace period and the queues for non-existent
SCSI devices never reach registration.

blk-mq basically needs to do the same thing - start the mq in a
degraded mode which is faster to shut down and then make it fully
functional only after the queue reaches registration.  percpu_ref
recently grew facilities to force atomic operation until explicitly
switched to percpu mode, which can be used for this purpose.  This
patch makes blk-mq initialize q->mq_usage_counter in atomic mode and
switch it to percpu mode only once blk_register_queue() is reached.

Note that this issue was previously worked around by 0a30288d
("blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during
probe") for v3.17.  The temp fix was reverted in preparation of adding
persistent atomic mode to percpu_ref by 9eca8046 ("Revert "blk-mq,
percpu_ref: implement a kludge for SCSI blk-mq stall during probe"").
This patch and the prerequisite percpu_ref changes will be merged
during v3.18 devel cycle.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NChristoph Hellwig <hch@infradead.org>
Link: http://lkml.kernel.org/g/20140919113815.GA10791@lst.de
Fixes: add703fd ("blk-mq: use percpu_ref for mq usage count")
Reviewed-by: NKent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Johannes Weiner <hannes@cmpxchg.org>
上级 1cae13e7
......@@ -402,6 +402,12 @@ static void blk_mq_sysfs_init(struct request_queue *q)
}
}
/* see blk_register_queue() */
void blk_mq_finish_init(struct request_queue *q)
{
percpu_ref_switch_to_percpu(&q->mq_usage_counter);
}
int blk_mq_register_disk(struct gendisk *disk)
{
struct device *dev = disk_to_dev(disk);
......
......@@ -1795,8 +1795,12 @@ struct request_queue *blk_mq_init_queue(struct blk_mq_tag_set *set)
if (!q)
goto err_hctxs;
/*
* Init percpu_ref in atomic mode so that it's faster to shutdown.
* See blk_register_queue() for details.
*/
if (percpu_ref_init(&q->mq_usage_counter, blk_mq_usage_counter_release,
0, GFP_KERNEL))
PERCPU_REF_INIT_ATOMIC, GFP_KERNEL))
goto err_map;
setup_timer(&q->timeout, blk_mq_rq_timer, (unsigned long) q);
......
......@@ -551,12 +551,19 @@ int blk_register_queue(struct gendisk *disk)
return -ENXIO;
/*
* Initialization must be complete by now. Finish the initial
* bypass from queue allocation.
* SCSI probing may synchronously create and destroy a lot of
* request_queues for non-existent devices. Shutting down a fully
* functional queue takes measureable wallclock time as RCU grace
* periods are involved. To avoid excessive latency in these
* cases, a request_queue starts out in a degraded mode which is
* faster to shut down and is made fully functional here as
* request_queues for non-existent devices never get registered.
*/
if (!blk_queue_init_done(q)) {
queue_flag_set_unlocked(QUEUE_FLAG_INIT_DONE, q);
blk_queue_bypass_end(q);
if (q->mq_ops)
blk_mq_finish_init(q);
}
ret = blk_trace_init_sysfs(dev);
......
......@@ -140,6 +140,7 @@ enum {
};
struct request_queue *blk_mq_init_queue(struct blk_mq_tag_set *);
void blk_mq_finish_init(struct request_queue *q);
int blk_mq_register_disk(struct gendisk *);
void blk_mq_unregister_disk(struct gendisk *);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册