ide: remove CONFIG_IDEDMA_{ICS,PCI}_AUTO config options

All modern distributions have been setting these options to "y" for ages.
(additionally "n" cases have been obsoleted for few years).  Therefore use
DMA by default and remove CONFIG_IDEDMA_{ICS,PCI}_AUTO (also remove no longer
needed CONFIG_IDEDMA_AUTO).  This fixes DMA support for rare configurations
where CONFIG_IDEDMA_{ICS,PCI}_AUTO was set to "n" but "hdparm -d 1" was used
to enable DMA support and which were forced to PIO mode by "ide: don't allow
DMA to be enabled if CONFIG_IDEDMA_{ICS,PCI}_AUTO=n" patch.  There is no
functionality loss because "ide=nodma" kernel option is still available.

Cc: Patrick Horn <phrh@yahoo.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
上级 6f5050a9
......@@ -434,24 +434,8 @@ config BLK_DEV_IDEDMA_FORCED
Generally say N here.
config IDEDMA_PCI_AUTO
bool "Use PCI DMA by default when available"
---help---
Prior to kernel version 2.1.112, Linux used to automatically use
DMA for IDE drives and chipsets which support it. Due to concerns
about a couple of cases where buggy hardware may have caused damage,
the default is now to NOT use DMA automatically. To revert to the
previous behaviour, say Y to this question.
If you suspect your hardware is at all flakey, say N here.
Do NOT email the IDE kernel people regarding this issue!
It is normally safe to answer Y to this question unless your
motherboard uses a VIA VP2 chipset, in which case you should say N.
config IDEDMA_ONLYDISK
bool "Enable DMA only for disks "
depends on IDEDMA_PCI_AUTO
help
This is used if you know your ATAPI Devices are going to fail DMA
Transfers.
......@@ -851,19 +835,6 @@ config BLK_DEV_IDEDMA_ICS
Say Y here if you want to add DMA (Direct Memory Access) support to
the ICS IDE driver.
config IDEDMA_ICS_AUTO
bool "Use ICS DMA by default"
depends on BLK_DEV_IDEDMA_ICS
help
Prior to kernel version 2.1.112, Linux used to automatically use
DMA for IDE drives and chipsets which support it. Due to concerns
about a couple of cases where buggy hardware may have caused damage,
the default is now to NOT use DMA automatically. To revert to the
previous behaviour, say Y to this question.
If you suspect your hardware is at all flakey, say N here.
Do NOT email the IDE kernel people regarding this issue!
config BLK_DEV_IDE_RAPIDE
tristate "RapIDE interface support"
depends on ARM && ARCH_ACORN
......@@ -1086,9 +1057,6 @@ config IDEDMA_IVB
It is normally safe to answer Y; however, the default is N.
config IDEDMA_AUTO
def_bool IDEDMA_PCI_AUTO || IDEDMA_ICS_AUTO
endif
config BLK_DEV_HD_ONLY
......
......@@ -196,11 +196,6 @@ static void icside_maskproc(ide_drive_t *drive, int mask)
}
#ifdef CONFIG_BLK_DEV_IDEDMA_ICS
#ifndef CONFIG_IDEDMA_ICS_AUTO
#warning CONFIG_IDEDMA_ICS_AUTO=n support is obsolete, and will be removed soon.
#endif
/*
* SG-DMA support.
*
......@@ -474,12 +469,6 @@ static int icside_dma_lostirq(ide_drive_t *drive)
static void icside_dma_init(ide_hwif_t *hwif)
{
int autodma = 0;
#ifdef CONFIG_IDEDMA_ICS_AUTO
autodma = 1;
#endif
printk(" %s: SG-DMA", hwif->name);
hwif->atapi_dma = 1;
......@@ -489,7 +478,7 @@ static void icside_dma_init(ide_hwif_t *hwif)
hwif->dmatable_cpu = NULL;
hwif->dmatable_dma = 0;
hwif->speedproc = icside_set_speed;
hwif->autodma = autodma;
hwif->autodma = 1;
hwif->ide_dma_check = icside_dma_check;
hwif->dma_host_off = icside_dma_host_off;
......
......@@ -177,11 +177,7 @@ DECLARE_MUTEX(ide_cfg_sem);
static int ide_scan_direction; /* THIS was formerly 2.2.x pci=reverse */
#endif
#ifdef CONFIG_IDEDMA_AUTO
int noautodma = 0;
#else
int noautodma = 1;
#endif
EXPORT_SYMBOL(noautodma);
......
......@@ -505,11 +505,6 @@ static void ide_hwif_setup_dma(struct pci_dev *dev, ide_pci_device_t *d, ide_hwi
}
}
}
#ifndef CONFIG_IDEDMA_PCI_AUTO
#warning CONFIG_IDEDMA_PCI_AUTO=n support is obsolete, and will be removed soon.
#endif
#endif /* CONFIG_BLK_DEV_IDEDMA_PCI*/
/**
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册