提交 00765f16 编写于 作者: H Hans de Goede 提交者: Mauro Carvalho Chehab

[media] gspca_sonixb: Add support for 0c45:602a

Add support for cameras with the HV7131D sensor, such as the 0c45:602a
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
上级 2b3e284a
......@@ -73,14 +73,15 @@ struct sd {
#define BRIDGE_103 1
__u8 sensor; /* Type of image sensor chip */
#define SENSOR_HV7131R 0
#define SENSOR_OV6650 1
#define SENSOR_OV7630 2
#define SENSOR_PAS106 3
#define SENSOR_PAS202 4
#define SENSOR_TAS5110C 5
#define SENSOR_TAS5110D 6
#define SENSOR_TAS5130CXX 7
#define SENSOR_HV7131D 0
#define SENSOR_HV7131R 1
#define SENSOR_OV6650 2
#define SENSOR_OV7630 3
#define SENSOR_PAS106 4
#define SENSOR_PAS202 5
#define SENSOR_TAS5110C 6
#define SENSOR_TAS5110D 7
#define SENSOR_TAS5130CXX 8
__u8 reg11;
};
......@@ -305,14 +306,29 @@ static const struct v4l2_pix_format sif_mode[] = {
.priv = 0},
};
static const __u8 initHv7131[] = {
static const __u8 initHv7131d[] = {
0x04, 0x03, 0x00, 0x04, 0x00, 0x00, 0x00, 0x80, 0x11, 0x00, 0x00, 0x00,
0x00, 0x00,
0x00, 0x00, 0x00, 0x02, 0x02, 0x00,
0x28, 0x1e, 0x60, 0x8e, 0x42,
0x1d, 0x10, 0x02, 0x03, 0x0f, 0x0c
};
static const __u8 hv7131d_sensor_init[][8] = {
{0xa0, 0x11, 0x01, 0x04, 0x00, 0x00, 0x00, 0x17},
{0xa0, 0x11, 0x02, 0x00, 0x00, 0x00, 0x00, 0x17},
{0xa0, 0x11, 0x28, 0x00, 0x00, 0x00, 0x00, 0x17},
{0xa0, 0x11, 0x30, 0x30, 0x00, 0x00, 0x00, 0x17}, /* reset level */
{0xa0, 0x11, 0x34, 0x02, 0x00, 0x00, 0x00, 0x17}, /* pixel bias volt */
};
static const __u8 initHv7131r[] = {
0x46, 0x77, 0x00, 0x04, 0x00, 0x00, 0x00, 0x80, 0x11, 0x00, 0x00, 0x00,
0x00, 0x00,
0x00, 0x00, 0x00, 0x02, 0x01, 0x00,
0x28, 0x1e, 0x60, 0x8a, 0x20,
0x1d, 0x10, 0x02, 0x03, 0x0f, 0x0c
};
static const __u8 hv7131_sensor_init[][8] = {
static const __u8 hv7131r_sensor_init[][8] = {
{0xc0, 0x11, 0x31, 0x38, 0x2a, 0x2e, 0x00, 0x10},
{0xa0, 0x11, 0x01, 0x08, 0x2a, 0x2e, 0x00, 0x10},
{0xb0, 0x11, 0x20, 0x00, 0xd0, 0x2e, 0x00, 0x10},
......@@ -553,7 +569,8 @@ static const __u8 tas5130_sensor_init[][8] = {
};
static struct sensor_data sensor_data[] = {
SENS(initHv7131, NULL, hv7131_sensor_init, NULL, NULL, 0, NO_EXPO|NO_FREQ, 0),
SENS(initHv7131d, NULL, hv7131d_sensor_init, NULL, NULL, F_GAIN, NO_BRIGHTNESS|NO_FREQ, 0),
SENS(initHv7131r, NULL, hv7131r_sensor_init, NULL, NULL, 0, NO_BRIGHTNESS|NO_EXPO|NO_FREQ, 0),
SENS(initOv6650, NULL, ov6650_sensor_init, NULL, NULL, F_GAIN|F_SIF, 0, 0x60),
SENS(initOv7630, initOv7630_3, ov7630_sensor_init, NULL, ov7630_sensor_init_3,
F_GAIN, 0, 0x21),
......@@ -703,7 +720,18 @@ static void setsensorgain(struct gspca_dev *gspca_dev)
unsigned char gain = sd->gain;
switch (sd->sensor) {
case SENSOR_HV7131D: {
__u8 i2c[] =
{0xc0, 0x11, 0x31, 0x00, 0x00, 0x00, 0x00, 0x17};
i2c[3] = 0x3f - (sd->gain / 4);
i2c[4] = 0x3f - (sd->gain / 4);
i2c[5] = 0x3f - (sd->gain / 4);
if (i2c_w(gspca_dev, i2c) < 0)
goto err;
break;
}
case SENSOR_TAS5110C:
case SENSOR_TAS5110D: {
__u8 i2c[] =
......@@ -790,6 +818,23 @@ static void setexposure(struct gspca_dev *gspca_dev)
struct sd *sd = (struct sd *) gspca_dev;
switch (sd->sensor) {
case SENSOR_HV7131D: {
/* Note the datasheet wrongly says line mode exposure uses reg
0x26 and 0x27, testing has shown 0x25 + 0x26 */
__u8 i2c[] = {0xc0, 0x11, 0x25, 0x00, 0x00, 0x00, 0x00, 0x17};
/* The HV7131D's exposure goes from 0 - 65535, we scale our
exposure of 0-1023 to 0-6138. There are 2 reasons for this:
1) This puts our exposure knee of 200 at approx the point
where the framerate starts dropping
2) At 6138 the framerate has already dropped to 2 fps,
going any lower makes little sense */
__u16 reg = sd->exposure * 6;
i2c[3] = reg >> 8;
i2c[4] = reg & 0xff;
if (i2c_w(gspca_dev, i2c) != 0)
goto err;
break;
}
case SENSOR_TAS5110C:
case SENSOR_TAS5110D: {
/* register 19's high nibble contains the sn9c10x clock divider
......@@ -1494,9 +1539,12 @@ static const struct usb_device_id device_table[] __devinitconst = {
#endif
{USB_DEVICE(0x0c45, 0x6028), SB(PAS202, 102)},
{USB_DEVICE(0x0c45, 0x6029), SB(PAS106, 102)},
{USB_DEVICE(0x0c45, 0x602a), SB(HV7131D, 102)},
/* {USB_DEVICE(0x0c45, 0x602b), SB(MI0343, 102)}, */
{USB_DEVICE(0x0c45, 0x602c), SB(OV7630, 102)},
{USB_DEVICE(0x0c45, 0x602d), SB(HV7131R, 102)},
{USB_DEVICE(0x0c45, 0x602e), SB(OV7630, 102)},
/* {USB_DEVICE(0x0c45, 0x602b), SB(MI03XX, 102)}, */ /* MI0343 MI0360 MI0330 */
{USB_DEVICE(0x0c45, 0x608f), SB(OV7630, 103)},
#if !defined CONFIG_USB_SN9C102 && !defined CONFIG_USB_SN9C102_MODULE
{USB_DEVICE(0x0c45, 0x60af), SB(PAS202, 103)},
......
......@@ -54,8 +54,8 @@ static const struct usb_device_id sn9c102_id_table[] = {
#if !defined CONFIG_USB_GSPCA_SONIXB && !defined CONFIG_USB_GSPCA_SONIXB_MODULE
{ SN9C102_USB_DEVICE(0x0c45, 0x6028, BRIDGE_SN9C102), },
{ SN9C102_USB_DEVICE(0x0c45, 0x6029, BRIDGE_SN9C102), },
#endif
{ SN9C102_USB_DEVICE(0x0c45, 0x602a, BRIDGE_SN9C102), },
#endif
{ SN9C102_USB_DEVICE(0x0c45, 0x602b, BRIDGE_SN9C102), },
#if !defined CONFIG_USB_GSPCA_SONIXB && !defined CONFIG_USB_GSPCA_SONIXB_MODULE
{ SN9C102_USB_DEVICE(0x0c45, 0x602c, BRIDGE_SN9C102), },
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册