[remove] configuration options for Kconfig

bsp/stm32/stm32f767-fire-challenger-v1/.config

@@ -567,12 +567,7 @@ CONFIG_BSP_USING_UART1=y
 # CONFIG_BSP_USING_UART2 is not set
 # CONFIG_BSP_USING_UART3 is not set
 # CONFIG_BSP_USING_ON_CHIP_FLASH is not set
-CONFIG_BSP_USING_SPI=y
-CONFIG_BSP_USING_SPI1=y
-CONFIG_BSP_SPI1_TX_USING_DMA=y
-CONFIG_BSP_SPI1_RX_USING_DMA=y
-# CONFIG_BSP_USING_SPI2 is not set
-# CONFIG_BSP_USING_SPI5 is not set
+# CONFIG_BSP_USING_SPI is not set
 # CONFIG_BSP_USING_QSPI is not set
 # CONFIG_BSP_USING_ADC is not set
 # CONFIG_BSP_USING_I2C1 is not set

bsp/stm32/stm32f767-fire-challenger-v1/board/Kconfig

@@ -104,57 +104,6 @@ menu "On-chip Peripheral Drivers"
     config BSP_USING_ON_CHIP_FLASH
         bool "Enable on-chip FLASH"
         default n
-        
-menuconfig BSP_USING_SPI
-        bool "Enable SPI BUS"
-        default n
-        select RT_USING_SPI
-        if BSP_USING_SPI
-            config BSP_USING_SPI1
-                bool "Enable SPI1 BUS"
-                default n
-
-            config BSP_SPI1_TX_USING_DMA
-                bool "Enable SPI1 TX DMA"
-                depends on BSP_USING_SPI1
-                default n
-                
-            config BSP_SPI1_RX_USING_DMA
-                bool "Enable SPI1 RX DMA"
-                depends on BSP_USING_SPI1
-                select BSP_SPI1_TX_USING_DMA
-                default n
-
-            config BSP_USING_SPI2
-                bool "Enable SPI2 BUS"
-                default n  
-                
-            config BSP_SPI2_TX_USING_DMA
-                bool "Enable SPI2 TX DMA"
-                depends on BSP_USING_SPI2
-                default n
-                
-            config BSP_SPI2_RX_USING_DMA
-                bool "Enable SPI2 RX DMA"
-                depends on BSP_USING_SPI2
-                select BSP_SPI2_TX_USING_DMA
-                default n
-
-            config BSP_USING_SPI5
-                bool "Enable SPI5 BUS"
-                default n  
-                
-            config BSP_SPI5_TX_USING_DMA
-                bool "Enable SPI5 TX DMA"
-                depends on BSP_USING_SPI5
-                default n
-                
-            config BSP_SPI5_RX_USING_DMA
-                bool "Enable SPI5 RX DMA"
-                depends on BSP_USING_SPI5
-                select BSP_SPI5_TX_USING_DMA
-                default n
-        endif
 
     config BSP_USING_QSPI
         bool "Enable QSPI BUS"

bsp/stm32/stm32f767-fire-challenger-v1/rtconfig.h

@@ -178,10 +178,6 @@
 #define BSP_USING_GPIO
 #define BSP_USING_UART
 #define BSP_USING_UART1
-#define BSP_USING_SPI
-#define BSP_USING_SPI1
-#define BSP_SPI1_TX_USING_DMA
-#define BSP_SPI1_RX_USING_DMA
 
 /* Board extended module Drivers */