Modified:
	configs/ls1012afrdm_qspi_defconfig
	configs/ls1012aqds_qspi_defconfig
	configs/ls1012ardb_qspi_defconfig
	include/configs/ls1012afrdm.h
	include/configs/ls1012aqds.h
	include/configs/ls1012ardb.h
Signed-off-by: NTom Rini <trini@konsulko.com>

For boards which have more devices it is necessary to extend malloc
space.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Nand and QSPI are not defined now but this will be extended.
Based on selected bootmode boot_targets are rewritten.
Patch also contains detection if variables are saved. If yes don't
rewrite boot_targets variable.

Also move variable setup to the end of file because SCSI needs to be
defined before others macros are using it.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NAlexander Graf <agraf@suse.de>

When the CONFIG_BOOTP_SERVERIP option is set, we ignore all
dhcp values for the tftp server and use our own serverip and
file name instead.

This is usually not what we want and I doubt it's set for a
good reason on ZynqMP. It definitely hurts if we want to support
uEFI PXE boot on it. So just remove the option for now.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Simplify zcu102 board file by moving CONFIG_AHCI enabling to common
file.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Enable support for RAM based FIT images read by SPL.
Empty function for now to keep compiler happy.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Setup flag when default environment are used to be able to
rewrite default distro boot variables based on SoC boot mode.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NAlexander Graf <agraf@suse.de>

Fix boot.bin generation for Zynq and ZynqMP.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NMarek Vasut <marex@denx.de>

0xc000 is not sufficient page table size if dc4 with 4 gems
is enabled.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

zc1751-dc4 contains four GEMs.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add debug uart for zc1751-dc2.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Phys are available on zc1751-dc4 that's why enable them.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Select MSR instructions via Kconfig instead of xparameters.h.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Toolchain can use some flags by default based on cpu version.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Remove autogenerated config.mk and select CPU options via Kconfig.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Simplify board file by enabling CMD_NAND via Kconfig.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Correct the nand ecc initialization code
This fixes the issue of incorrect nand ecc
init if no device is found in ecc_matrix then
it endsup ecc init with junk initialization
instead of the most suited one.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Repair typos in the previous "arm: lib: fix push/pop-section directives"
patch, which prevented VCMA9 board from building.
Signed-off-by: NMarek Vasut <marex@denx.de>
Fixes: b2f18584 ("arm: lib: fix push/pop-section directives")
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stephen Warren <swarren@nvidia.com>

When no DTB can be matched successfully to the board that's being used
a list of available FIT-embedded DTBs will be output to the console for
diagnostic purposes. But rather than the contents of the "description"
FDT property a non-existent property was accessed and as a result "NULL"
was output instead of the actual name(s) of the DTB(s). Fix this issue
by using the correct property which is also the exact same property
that's used earlier during the actual board matching process.
Signed-off-by: NAndreas Dannenberg <dannenberg@ti.com>

No intended functional change, just remove redundancies in some
Makefiles, and make whitespace aesthetics uniform.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Add some tests for the new open drain setting feature of the GPIO
uclass, and extend the capabilities of the sandbox GPIO driver
accordingly.
Signed-off-by: NMario Six <mario.six@gdsys.cc>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NYork Sun <york.sun@nxp.com>

This patch implements the open-drain setting feature for the MPC85XX
GPIO controller.
Signed-off-by: NMario Six <mario.six@gdsys.cc>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Certain GPIO devices have the capability to switch their GPIOs into
open-drain mode, that is, instead of actively driving the output
(Push-pull output), the pin is connected to the collector (for a NPN
transistor) or the drain (for a MOSFET) of a transistor, respectively.
The pin then either forms an open circuit or a connection to ground,
depending on the state of the transistor.

This patch adds functions to the GPIO uclass to switch GPIOs to
open-drain mode on devices that support it.
Signed-off-by: NMario Six <mario.six@gdsys.cc>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NYork Sun <york.sun@nxp.com>

This patch adds a driver for the built-in GPIO controller of the MPC85XX
SoC (probably supporting other PowerQUICC III SoCs as well).

Each GPIO bank is identified by its own entry in the device tree, i.e.

gpio-controller@fc00 {
      #gpio-cells = <2>;
      compatible = "fsl,pq3-gpio";
      reg = <0xfc00 0x100>
}

By default, each bank is assumed to have 32 GPIOs, but the ngpios
setting is honored, so the number of GPIOs for each bank in configurable
to match the actual GPIO count of the SoC (e.g. the 32/32/23 banks of
the P1022 SoC).

The usual functions of GPIO drivers (setting input/output mode and output
value setting) are supported.

The driver has been tested on MPC85XX, but it is likely that other
PowerQUICC III devices will work as well.
Signed-off-by: NMario Six <mario.six@gdsys.cc>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Replace a number of array length calculations with the ARRAY_SIZE()
macro, for clarity.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: NYork Sun <york.sun@nxp.com>

We should use unified setup_ddr_tlbs() for spl boot and non-spl boot
to make sure 'M' bit is set for DDR TLB to maintain cache coherence.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

For malloc to work in SPL framework enable GD_FLG_FULL_MALLOC_INIT
flag in global data after allocating memory using mem_malloc_init.
Signed-off-by: NSumit Garg <sumit.garg@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

The mtd subsystem deprecated and renamed the direct use of the mtd_info
struct's functionpointers. Instead the corresponding mtd_xxx function
should be used.

See also:
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=3c3c10bba1e4ccb75b41442e45c1a072f6cded19Signed-off-by: NMax Krummenacher <max.krummenacher@toradex.com>

Updates the NAND code to match Linux v4.6.  The previous sync was from
Linux v4.1 in commit d3963721.

Note that none of the individual NAND drivers tracked Linux closely
enough to be synced themselves, other than manually applying a few
cross-tree changes.
Signed-off-by: NScott Wood <oss@buserror.net>
Tested-by: NHeiko Schocher <hs@denx.de>

This change is part of the Linux 4.6 sync.  It is being done before the
main sync patch in order to make it easier to address the issue across
all NAND drivers (many/most of which do not closely track their Linux
counterparts) separately from other merge issues.
Signed-off-by: NScott Wood <oss@buserror.net>

These functions are part of the Linux 4.6 sync.  They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.
Signed-off-by: NScott Wood <oss@buserror.net>

nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.

This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip.  It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: NScott Wood <oss@buserror.net>

This typedef serves no purpose other than causing confusion with
struct nand_chip.
Signed-off-by: NScott Wood <oss@buserror.net>

Commit ad4f54ea ("arm: Remove palmtreo680 board") removed the only
user of the docg4 driver and the palmtreo680 image flashing tool.  This
patch removes them.
Signed-off-by: NScott Wood <oss@buserror.net>
Cc: Mike Dunn <mikedunn@newsguy.com>
Cc: Simon Glass <sjg@chromium.org>

This driver is not used by anyone, remove it.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Scott Wood <oss@buserror.net>
Acked-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: NScott Wood <oss@buserror.net>

Correct the nand ecc initialization code
This fixes the issue of incorrect nand ecc
init if no device is found in ecc_matrix then
it endsup ecc init with junk initialization
instead of the most suited one.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: NMichal Simek <michal.simek@xilinx.com>