The Mele_A1000G_quad has an onboard usb <-> sata conversion which needs
longer then the usb-spec allows to connect after getting power.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

These are used for the usb wifi and if we leave the enabling up to the
kernel, we get hit by the axp209 issues with enabling ldo3 or 4 post boot
and the systems hangs as soon as it is enabled.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

In the draco CPU board family, etamin is a new variant
with bigger flash and more RAM. Due to new flash that
uses larger pages (4K) some changes are necessary because
it impacts the MTD partition layout and the ubi mount
parameters.
Signed-off-by: NSamuel Egli <samuel.egli@siemens.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
[trini: Move BOOTDELAY into defconfig, just always be 3 now]
Signed-off-by: NTom Rini <trini@konsulko.com>

writting to ubi nand partitions need after write ends an erase
of the remaining sectors. This fail, if dfu write size was not
a multiple of erasesize, example log:

Failure erase: -1

Fix this error.
Signed-off-by: NHeiko Schocher <hs@denx.de>

read the ECC Type field from the i2c eeprom, instead
configuring it static in the U-Boot binary.

see RM:
Table 26-17. NAND Geometry Information on I2C EEPROM
Signed-off-by: NHeiko Schocher <hs@denx.de>

support in omap_nand_switch_ecc() also an eccstrength
from 16.
Signed-off-by: NHeiko Schocher <hs@denx.de>

add for nand devices mtd concat support. Generic MTD concat
support is already ported to mainline, and used in the cfi_mtd
driver. This patch adds it similiar for nand devices.
Signed-off-by: NHeiko Schocher <hs@denx.de>

simple detachs ubi from the mtd partition.
Signed-off-by: NHeiko Schocher <hs@denx.de>

From: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>

U-Boot SPL 2016.03-rc3-00019-g6dfb4c2-dirty (Mar 09 2016 - 07:40:06)
SHC C3-Sample
MPU reference clock runs at 6 MHz
Setting MPU clock to 594 MHz
Enabling Spread Spectrum of 18 permille for MPU
Trying to boot from MMC
reading u-boot.img
reading u-boot.img

U-Boot 2016.03-rc3-00019-g6dfb4c2-dirty (Mar 09 2016 - 07:05:35 +0100)

       Watchdog enabled
I2C:   ready
DRAM:  512 MiB
reloc off 1f783000
MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1
Net:   cpsw
U-Boot#
Signed-off-by: NHeiko Schocher <hs@denx.de>

on the shc board we see when booting in net boot mode,
that the ROM bootloader sends "AM335x ROM" as
vendor-class-identifier. U-Boots doc says "DM814x ROM".

So, add the info to the doc, that there is also
"AM335x ROM" possible.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>

make this function weak, so board code can setup in SPL
MMC init with board special values.
Signed-off-by: NHeiko Schocher <hs@denx.de>

Enable 8bit interface on HSMMC2 for am33xx to support 8bit eMMC chips.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>

revert patch:
commit: 6b2221b0: mmc: Handle switch error status bit in MMC card status

to get eMMC working on shc board
Signed-off-by: NHeiko Schocher <hs@denx.de>

show_boot_progress() is now called from SPL also.
Signed-off-by: NHeiko Schocher <hs@denx.de>

Enable Spread Spectrum for the MPU by calculating the required
values and setting the registers accordingly.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>

add missing CM_CLKMODE_DPLL_SSC_ACK_MASK,
CM_CLKMODE_DPLL_SSC_DOWNSPREAD_MASK and
CM_CLKMODE_DPLL_SSC_TYPE_MASK
defines. Used for enabling spread spectrum.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>

add missing:
OMAP_GPIO_IRQSTATUS_SET_0 and OMAP_GPIO_IRQSTATUS_SET_1
registers.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>

add the following defines, needed for the upcoming shc board
support:
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>

if CONFIG_VERSION_VARIABLE is set, the U-Boot environment
contains a "vers" variable with the current U-Boot version
string. If now "printenv" is called, test/py fails as it
detects the main_sign string, which is in this case correct.

So check only the main_sign as an error, if CONFIG_VERSION_VARIABLE
is not set.
Signed-off-by: NHeiko Schocher <hs@denx.de>

move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>

This current code passes the variable arguments list to sprintf(). This is
not correct. Fix it by calling _vprintf() directly.

This makes firefly-rk3288 boot again.

Fixes: abeb272d ("tiny-printf: Support snprintf()")
Reviewed-by: NStefan Roese <sr@denx.de>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NSimon Glass <sjg@chromium.org>

I noticed secondary CPUs sometimes fail to wake up, and the root
cause is that the sev instruction wakes up slave CPUs before the
preceding the register write is observed by them.

The read-back of the accessed register does not guarantee the order.
In order to ensure the order between the register write and the sev
instruction, a dsb instruction should be executed prior to the sev.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Unlike NAND, eMMC can be re-written without erasing.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

This code auto-detects the best-match FDT file name, but it should
respect the user's choice if "fdt_file" environment is found in a
saved set of environments.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Because setenv() may fail, it is better to check its return code.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

This function is shared between PH1-LD11 and PH1-LD20.  The difference
is the boot-mode latch for the USB boot mode.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

The Boot ROM on PH1-LD11/LD20 exports built-in APIs to load images
from an eMMC device.  They are useful to reduce the memory footprint
of SPL, rather than compiling the whole MMC framework.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Signed-off-by: NTom Rini <trini@konsulko.com>

Signed-off-by: NTom Rini <trini@konsulko.com>

Conflicts:
	configs/peach-pi_defconfig
	configs/peach-pit_defconfig

Avoid use of hard coded mmcdev value, use bootpart
instead, so finduuid works based on bootpart set
for a specific platform.
Signed-off-by: NRavi Babu <ravibabu@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Some SPL loaders (like Allwinner's boot0, and Broadcom's boot0)
require a header before the actual U-Boot binary to both check its
validity and to find other data to load. Sometimes this header may
only be a few bytes of information, and sometimes this might simply
be space that needs to be reserved for a post-processing tool.

Introduce a config option to allow assembler preprocessor commands
to be inserted into the code at the appropriate location; typical
assembler preprocessor commands might be:
  .space 1000
  .word 0x12345678
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NSteve Rae <srae@broadcom.com>
Commit Notes:
Please note that the current code:
  start.S (arm64) and
  vectors.S (arm)
already jumps over some portion of data already, so this option basically
just increases the size of this region (and the resulting binary).

For use with Allwinner's boot0 blob there is a tool called boot0img[1],
which fills the header to allow booting A64 based boards.
For the Pine64 we need a 1536 byte header (including the branch
instruction) at the moment, so we add this to the defconfig.

[1] https://github.com/apritzel/pine64/tree/master/tools
END
Reviewed-by: NTom Rini <trini@konsulko.com>

When setting up a DDR controller it is useful to be able to display
frequencies in a readable form. Make the strmhz() function available in
SPL builds provided there is full vsprintf available.
Reviewed-by: NTony O'Brien <tony.obrien@alliedtelesis.co.nz>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NChris Packham <judge.packham@gmail.com>

Since bcopy() is no longer used, delete all remaining references to
it.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>

Now that all Keystone2 dts file names are changed in Linux kernel, reflect the
same in evn variables inorder to find the right dtb file.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Use a single defconfig for all DRA7xx hs platforms by enabling FIT and delete
the platform specific defconfigs.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Acked-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>

Some systems are starting to shift to support DM_VIDEO which exposes
the frame buffer through a slightly different interface.

This is a poor man's effort to support the dm video interface instead
of the lcd one. We still only support a single display device.
Signed-off-by: NAlexander Graf <agraf@suse.de>
[trini: Remove fb_size / fb_base as they were not used]
Signed-off-by: NTom Rini <trini@konsulko.com>

When a payload calls our memory allocator with the exact address hint, we
happily allocate memory from completely unpopulated regions. Payloads however
expect this to only succeed if they would be allocating from free conventional
memory.

This patch makes the logic behind those checks a bit more obvious and ensures
that we always allocate from known good free conventional memory regions if we
want to allocate ram.
Reported-by: NJonathan Gray <jsg@jsg.id.au>
Signed-off-by: NAlexander Graf <agraf@suse.de>

We introduced special "DEBUG_EFI" defines when the efi loader
support was new. After giving it a bit of thought, turns out
we really didn't have to - the normal #define DEBUG infrastructure
works well enough for efi loader as well.

So this patch switches to the common debug() and #define DEBUG
way of printing debug information.
Signed-off-by: NAlexander Graf <agraf@suse.de>