- 23 3月, 2018 40 次提交
-
-
由 Vipul Kumar 提交于
This patch changed CONFIG_SYS_MEMTEST_SCRATCH address to the accessible DDR address used by alternate memory test. Before this, 0xfffc0000 address was used, which is the OCM address and not enabled in MMU table. So, whenever trying to access 0xfffc0000 address, got Synchronous Abort exception. After changing CONFIG_SYS_MEMTEST_SCRATCH address, alternate memory test is working fine. Signed-off-by: NVipul Kumar <vipulk@xilinx.com> Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Enable watchdog with reset-on-timeout feature. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Watchdog is only enabled in full u-boot. Adoption for SPL should be also done because that's the right place where watchdog should be enabled. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Shreenidhi Shedi 提交于
This IP can be found on Zynq and ZynqMP devices. The driver was tested with reset-on-timeout; feature. Also adding WATCHDOG symbol to Kconfig because it is required. Signed-off-by: NShreenidhi Shedi <imshedi@gmail.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
watchdog clock is also connected to cpu 1X clocksource. Zynq> clk dump ... Before: swdt 4294967290 After: swdt 111111110 Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
As of now newer pmufw is keeping old interfaces. That's why permit u-boot to run on newer version. Recommended version will be setup later. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch bypasses phy detection logic for GMII interface and just depend on phy address received from DT. This patch is required as phy detection logic is different for some phys like xilinx phy which can be connected over SGMII and GMII interface. This fixes the issue of ethernet failures when xilinx phy is connected over GMII interface. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Nitin Jain 提交于
This patch is adding support to switch to EL1 while loading an EL1 application with u-boot running at EL above EL1 in aarch64 mode. Signed-off-by: NNitin Jain <nitinj@xilinx.com> Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
It helps with debugging. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Enable missing driver on this board. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Check !desc earlier to simplify code. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Acked-by: NSimon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com> Reviewed-by: NSimon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
-
由 Michal Simek 提交于
Make defconfigs up2date with current location. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Use zynqmp clock driver instead of fixed clocks. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
-
由 Lokesh Vutla 提交于
Enable Driver Model and Device-tree support for omapl138 board in U-Boot. Also enable DM_SERIAL and DM_I2C. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
Sync dts from Linux 4.16 and also add u-boot specific dtsi for OMAPl138 board. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
Commit 6aa4ad8e ("Convert CONFIG_SOC_DA8XX et al to Kconfig") converted SOC_DA8XX to Kconfig but missed enabling DDR_INIT for SOC_DA8XX, which broke OMAPL138 to boot. Commit 2e879805 ("davinci: Fix omapl138_lcdk builds") disabled DDR_INIT for all DA850 SoCs. This failed all DA850 boards to boot as ddr is not being initialized. Enable SYS_DA850_DDR_INIT for DA8XX so that all DA850 and OMAPL138 will have ddr initialized Fixes: 2e879805 ("davinci: Fix omapl138_lcdk builds") Fixes: 6aa4ad8e ("Convert CONFIG_SOC_DA8XX et al to Kconfig") Reported-by: NSekhar Nori <nsekhar@ti.com> Tested-by: NSekhar Nori <nsekhar@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NDavid Lechner <david@lechnology.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Faiz Abbas 提交于
With gpio devices getting created in SPL, the size of the heap is no longer sufficient. Therefore, increase SPL_SYS_MALLOC_F_LEN to 0x1000. Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Faiz Abbas 提交于
With DM enabled in SPL, DM_FLAG_PRE_RELOC is required for the omap_gpio driver to be bound to the gpio devices. Therefore, add DM_FLAG_PRE_RELOC flag to the omap_gpio driver. Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Luca Ceresoli 提交于
scripts/check-config.sh exits successfully and silently without doing any checks when the 'comm' command is not found. The problem triggers from the command around line 39: comm -23 ${suspects} ${ok} >${new_adhoc} This statement fails when 'comm' is not in $PATH, creating an empty ${new_adhoc} file. But the script continues and the following line, which is supposed to detect an error: if [ -s ${new_adhoc} ]; then will always be false since the file is empty, and the script will exit successfully as if everything were OK. The case where 'comm' in not in $PATH is not theoretical. It used to happen on yocto until a recent fix [0], and still happens on the current stable branch (rocko). Fix by setting the errexit flag to exit with error when a statement fails, so that at least the problem is noticed. For additional safety also set the nounset flag to detect expansion errors. [0] http://git.yoctoproject.org/cgit/cgit.cgi/poky/commit/?id=fe0b4cb5b48580d4a3f3c0eb82bfa6f1b13801e4Signed-off-by: NLuca Ceresoli <luca@lucaceresoli.net> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 David Lechner 提交于
commit 1601dd97 ("davinci: omapl138_lcdk: increase PLL0 frequency") changed the PLL0 frequency to 456MHz, which is needed for the LCDC IP block. However, in doing so, it caused the PLLOUT clock to be outside of the allowable specifications given in the OMAP-L138 data sheet. (It says PLLOUT must be 600MHz max). It also uses a PLLM value outside of the range given in the TRM (it says PLLM must in the range 0 to 0x1f). So here is what we have currently: PLLOUT = 24 / (0 + 1) * (37 + 1) = 912MHz (out of spec) ^ ^ ^ CLKIN PREDIV PLLM (out of spec) input to PLLDIVn = 912 / (1 + 1) = 456MHz (desired result) ^ ^ PLLOUT POSTDIV This changes the PLLM value to 18 and the POSTDIV value to 0 so that PLLOUT is now within specification but we still get the desired result. PLLOUT = 24 / (0 + 1) * (18 + 1) = 456MHz (within spec) ^ ^ ^ CLKIN PREDIV PLLM input to PLLDIVn = 456 / (0 + 1) = 456MHz (desired result) ^ ^ PLLOUT POSTDIV Fixes: 1601dd97 ("davinci: omapl138_lcdk: increase PLL0 frequency") Signed-off-by: NDavid Lechner <david@lechnology.com> Reported-by: NSekhar Nori <nsekhar@ti.com> Tested-by: NSekhar Nori <nsekhar@ti.com>
-
由 Liam Beguin 提交于
Add basic tests for the spi_flash subsystem. Signed-off-by: NLiam Beguin <liambeguin@gmail.com> Reviewed-by: NStephen Warren <swarren@nvidia.com>
-
由 Tuomas Tynkkynen 提交于
Last user of this driver went away in October 2014 in commit d58a9451 ("ppc/arm: zap EMK boards"). Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Heinrich Schuchardt 提交于
In if (a > =0) {...} else (a < 0) {...} the second logical constraint is superfluous. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Heinrich Schuchardt 提交于
In int ret = A; ret = B; the first assignment has not effect. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Alexander Graf 提交于
The lan75xx and lan78xx drivers need to drive their phy via the generic phylib framework. Let's reflect that dependency in Kconfig, so that we don't get build errors when phylib does not get selected. Signed-off-by: NAlexander Graf <agraf@suse.de> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Alexander Graf 提交于
In the efi_loader main loop we call eth_rx() occasionally. This rx function might end up calling into devices that haven't been initialized yet, potentially resulting in a lot of transfer timeouts. Instead, let's make sure the ethernet device is actually initialized before reading from or writing to it. Signed-off-by: NAlexander Graf <agraf@suse.de> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Leonid Iziumtsev 提交于
The "net_try_count" counter starts from "1". And the "retrycnt" contains requested amount of retries. With current logic, that means that the actual retry amount will be one time less then what we set in "netretry" env. For example setting "netretry" to "once" will make "retrycnt" equal "1", so no retries will be triggered at all. Fix the logic by changing the statement of "if" condition. Signed-off-by: NLeonid Iziumtsev <leonid.iziumtsev@se.atlascopco.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Priyanka Jain 提交于
Current Cortina phy driver assumes that firmware upload is required during initialization and is dependent on presence of corresponding macros like CONFIG_CORTINA_FW_ADDR for compilation. But Cortina phy has provision to store phy firmware in attached dedicated EEPROM. And boards designed with such EEPROM does not require firmware upload. Add CORTINA_NO_FW_UPLOAD option in cortina.c to support such boards. Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Priyanka Jain 提交于
Update get_phy_id() implementation in cortina.c to check for Cortina_phy by comparing device phy_id with cortina phy_id instead of relying on presence of CORTINA macros. This will allow get_phy_id to work with non-cortina phy devices which might have same phy address as Cortina device but on different bus. Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Calvin Johnson 提交于
Add configurations for PFE. Signed-off-by: NCalvin Johnson <calvin.johnson@nxp.com> Signed-off-by: NAnjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Calvin Johnson 提交于
Enable all types of non-secure access to PFE block registers. Signed-off-by: NCalvin Johnson <calvin.johnson@nxp.com> Signed-off-by: NAnjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Calvin Johnson 提交于
1. Set AWCACHE0 attribute of PFE DDR and HDBUS master interfaces to bufferable. 2. Set RD/WR QoS for PFE DDR and HDBUS AXI master interfaces. 3. Disable ECC detection for PFE. Signed-off-by: NCalvin Johnson <calvin.johnson@nxp.com> Signed-off-by: NAnjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Calvin Johnson 提交于
SoC specific PFE macros are defined and structure ccsr_scfg is updated with members defined for PFE. Signed-off-by: NCalvin Johnson <calvin.johnson@nxp.com> Signed-off-by: NAnjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Calvin Johnson 提交于
This patch enables ethernet support for ls1012a2g5rdb. Signed-off-by: NCalvin Johnson <calvin.johnson@nxp.com> Signed-off-by: NBhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Calvin Johnson 提交于
This patch enables ethernet support for ls1012ardb. Signed-off-by: NCalvin Johnson <calvin.johnson@nxp.com> Signed-off-by: NAnjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Calvin Johnson 提交于
This patch enables ethernet support for ls1012afrdm. Signed-off-by: NCalvin Johnson <calvin.johnson@nxp.com> Signed-off-by: NAnjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Calvin Johnson 提交于
This patch enables ethernet support for ls1012aqds. Signed-off-by: NCalvin Johnson <calvin.johnson@nxp.com> Signed-off-by: NAnjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Calvin Johnson 提交于
Contains all the pfe header files. Signed-off-by: NCalvin Johnson <calvin.johnson@nxp.com> Signed-off-by: NAnjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Calvin Johnson 提交于
pfe_command provides command line support for several features that support pfe, like starting or stopping the pfe, checking the health of the processor engines and checking status of different units inside pfe. Signed-off-by: NCalvin Johnson <calvin.johnson@nxp.com> Signed-off-by: NAnjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-