- 18 10月, 2020 1 次提交
-
-
由 Patrick Delaunay 提交于
Done with: ./tools/moveconfig.py VIDEO_BMP_RLE8 Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
- 10 10月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 24 8月, 2020 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_SPLASH_SCREEN CONFIG_SPLASH_SCREEN_ALIGN CONFIG_SPLASHIMAGE_GUARD CONFIG_SPLASH_SOURCE Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 29 7月, 2020 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 28 7月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 17 7月, 2020 1 次提交
-
-
由 Tom Rini 提交于
This converts the following to Kconfig: CONFIG_MXC_UART Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NPeng Fan <peng.fan@nxp.com>
-
- 07 7月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 5月, 2020 1 次提交
-
-
由 Ashok Reddy Soma 提交于
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 07 2月, 2020 1 次提交
-
-
由 Anatolij Gustschin 提交于
This partially reverts changes by commit 2cc393f3 ("video: make BPP and ANSI configs optional") since it caused issues with other boards (missing LCD console output on pinebook, x86 platform or sandbox). Enable all disabled options again and opt out of not supported color depth in board defconfigs. Signed-off-by: NAnatolij Gustschin <agust@denx.de> Reported-by: NVagrant Cascadian <vagrant@debian.org>
-
- 23 1月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 1月, 2020 2 次提交
-
-
由 Joris Offouga 提交于
Signed-off-by: NJoris Offouga <offougajoris@gmail.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Joris Offouga 提交于
For DM_ETH support , it's require to disable this config. When this config is enable, This generate a error with spl in linker script Signed-off-by: NJoris Offouga <offougajoris@gmail.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
- 06 12月, 2019 1 次提交
-
-
由 Anatolij Gustschin 提交于
Many boards do not use all selected framebuffer depth configurations, for such boards there is some unused code in video and console uclass routines. Make depth specific code optional to avoid dead code and slightly reduce binary size. Also make ANSI code optional for the same reason. When i.e. using only VIDEO_BPP16 the code size shrinks (below values when using gcc-7.3.0): $ ./tools/buildman/buildman -b video-wip -sS wandboard ... 01: Merge git://git.denx.de/u-boot-sh 02: video: add guards around 16bpp/32bbp code 03: video: make BPP and ANSI configs optional arm: (for 1/1 boards) all -776.0 bss -8.0 text -768.0 Signed-off-by: NAnatolij Gustschin <agust@denx.de> Tested-by: NEugen Hristev <eugen.hristev@microchip.com> Tested-by: NPatrice Chotard <patrice.chotard@st.com> Tested-by: NSteffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
-
- 04 12月, 2019 1 次提交
-
-
由 Miquel Raynal 提交于
Like in Linux, just use CONFIG_MTD to compile the MTD stack. Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com>
-
- 21 11月, 2019 2 次提交
-
-
由 Tom Rini 提交于
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
-
由 Tom Rini 提交于
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 08 11月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 14 10月, 2019 1 次提交
-
-
由 Jun Nie 提交于
Add config to enable CAAM so that hardware random number generator works. Signed-off-by: NJun Nie <jun.nie@linaro.org>
-
- 08 10月, 2019 2 次提交
-
-
由 Joris Offouga 提交于
Signed-off-by: NJoris Offouga <offougajoris@gmail.com> Reviewed-by: NOtavio Salvador <otavio@ossystems.com.br>
-
由 Joris Offouga 提交于
This commit convert all pico-imx7d to DM_VIDEO Signed-off-by: NJoris Offouga <offougajoris@gmail.com>
-
- 24 8月, 2019 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_FSL_USDHC Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 14 8月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 20 7月, 2019 1 次提交
-
-
由 Joris Offouga 提交于
This patch enable usb support with device-tree Signed-off-by: NJoris Offouga <offougajoris@gmail.com> Reviewed-by: NJun Nie <jun.nie@linaro.org>
-
- 23 6月, 2019 1 次提交
-
-
由 Yangbo Lu 提交于
Converted to use fsl_esdhc_imx for i.MX platforms. Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com> Tested-by: NSteffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Reviewed-by: NPeng Fan <peng.fan@nxp.com> Reviewed-by: NLukasz Majewski <lukma@denx.de> Reviewed-by: NMartyn Welch <martyn.welch@collabora.com> Acked-by: NJason Liu <Jason.hui.liu@nxp.com>
-
- 11 6月, 2019 1 次提交
-
-
由 Jun Nie 提交于
Add default configuration to run u-boot as BL33 in the boot flow case of ATF(ARM Trusted Firmware) -> OPTEE -> U-boot. Signed-off-by: NJun Nie <jun.nie@linaro.org> Reviewed-by: NFabio Estevam <festevam@gmail.com>
-
- 27 5月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 05 5月, 2019 1 次提交
-
-
由 Alex Kiernan 提交于
This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com> Acked-by: NLukasz Majewski <lukma@denx.de> Acked-by: NPatrick Delaunay <patrick.delaunay@st.com> Acked-by: NRamon Fried <ramon.fried@gmail.com> Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
-
- 30 4月, 2019 2 次提交
-
-
由 Simon Goldschmidt 提交于
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 26 4月, 2019 3 次提交
-
-
由 Joris Offouga 提交于
This patch enable convert DM MMC for imx7d-pico board and variant. Before the DM conversion only usdhc3 was enabled and therefore it appeared as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2, which left unattended would drive changes to existing pico-pi bootscripts and environment variables that rely on mmc 0. Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will work unmodified. When converting to DM_MMC it is necessary that SPL initializes eMMC by itself, so move the original eMMC initialization from U-Boot proper to SPL. Signed-off-by: NJoris Offouga <offougajoris@gmail.com> Signed-off-by: NFabio Estevam <festevam@gmail.com>
-
由 Joris Offouga 提交于
This patch is necessary for convert this board to dm driver model DM GPIO requires gpio_request() to be called explicitly before doing any gpio operation Signed-off-by: NJoris Offouga <offougajoris@gmail.com>
-
由 Joris Offouga 提交于
This patch adds DT file hooks for Pico i.MX7D SOM and variant boards Signed-off-by: NJoris Offouga <offougajoris@gmail.com>
-
- 28 1月, 2019 1 次提交
-
-
由 Fabio Estevam 提交于
Add support for the VXT VL050-8048NT-C01 panel connected through the 24 bit parallel LCDIF interface. Signed-off-by: NFabio Estevam <festevam@gmail.com> Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
-
- 19 1月, 2019 1 次提交
-
-
由 Philipp Tomsich 提交于
The bounce buffer is used by a few drivers (most of the MMC drivers) to overcome limitations in their respective DMA implementation. This moves the configuration to Kconfig and makes it user-selectable (even though it will be a required feature to make those drivers work): the expected usage is for drivers depending on this to 'select' it unconditionally from their respective Kconfig (see follow-up patches). This commit includes a full migration using moveconfig.py to ensure that each commit compiles. To ensure bisectability we update dependencies of various drivers to now select BOUNCE_BUFFER when needed. [trini: Squash all patches to ensure bisectability] Signed-off-by: NTom Rini <trini@konsulko.com> Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion] Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion] Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
-
- 11 1月, 2019 1 次提交
-
-
由 Jean-Jacques Hiblot 提交于
The SPL option for USB gadget should be named after the option for u-boot (CONFIG_USB_GADGET) Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
-
- 08 1月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 10 10月, 2018 1 次提交
-
-
由 Fabio Estevam 提交于
Currently SPL binary is larger than 64kB, which is larger than CONFIG_SPL_MAX_SIZE defined in imx7_spl.h. This causes boot failure on the pico-mx7 targets. Remove CONFIG_SPL_LIBDISK_SUPPORT option for now, so that the SPL binary can fit into the 64kB range. Signed-off-by: NFabio Estevam <festevam@gmail.com> Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
-
- 18 8月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: NAdam Ford <aford173@gmail.com> Acked-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 17 8月, 2018 1 次提交
-
-
由 Tom Rini 提交于
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 23 7月, 2018 1 次提交
-
-
由 Otavio Salvador 提交于
This enables the "bootaux" command so a firmware can be loaded inside the M4 MCU. Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
-