When using allocated platform data, allocate it when we bind the device.
This makes it possible to fill in this information before the device is
probed.

This fits with the platform data model (when not using device tree),
since platform data exists at bind-time.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

Make the error handling more standard to make it easier to build on top of
it. Also correct a bug in the error path where there is no parent.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

The root device corresponds to the root device tree node, so set this up.
Also add a few notes to the documentation.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Mention that the devices are probed ready for use.
Signed-off-by: NSimon Glass <sjg@chromium.org>

There is no point in running the tests if U-Boot cannot be built. Abort in
this case.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Rather than assuming that the chip offset length is 1, allow it to be
provided. This allows chips that don't use the default offset length to
be used (at present they are only supported by the command line 'i2c'
command which sets the offset length explicitly).
Signed-off-by: NSimon Glass <sjg@chromium.org>
Acked-by: NHeiko Schocher <hs@denx.de>

For boards which use multiple I2C devices, or for SOCs which support
multiple boards, we might want to convert these to driver model at different
times. At present this is difficult because we need to either use
CONFIG_DM_I2C for a board or not.

Add a compatibility layer which implements the old API, thus allowing a
board to move to driver model for I2C without requiring that everything it
uses is moved in the same commit.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Add a dm_ prefix to driver model I2C functions so that we can keep the old
ones around.

This is a little unfortunate, but on reflection it is too difficult to
change the API. We can undo this rename when most boards and drivers are
converted to use driver model for I2C.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Since GPIO support has now moved to the driver model uclass, we can drop
this include.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Now that we support device tree GPIO bindings directly in the driver model
GPIO uclass we can remove these functions.
Signed-off-by: NSimon Glass <sjg@chromium.org>

U-Boot now supports using GPIOs using bank phandles instead of global
numbers. Update the exynos device tree files to use this.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Acked-by: NMinkyu Kang <mk7.kang@samsung.com>

This new method is much easier and matches the kernel.
Signed-off-by: NSimon Glass <sjg@chromium.org>

These functions are going away, so use the new uclass support instead.
Signed-off-by: NSimon Glass <sjg@chromium.org>

These functions are going away, so use the new uclass support instead.
Signed-off-by: NSimon Glass <sjg@chromium.org>

These functions are going away, so use the new uclass support instead.
Signed-off-by: NSimon Glass <sjg@chromium.org>

These functions serve no useful purpose, and conflict with the generic API.
Drop them.
Signed-off-by: NSimon Glass <sjg@chromium.org>

These functions are going away, so use the new uclass support instead.
Signed-off-by: NSimon Glass <sjg@chromium.org>

These functions are going away, so use the new uclass support instead.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This deals with the polarity bit. It also changes the GPIO devices so that
the correct device tree node is linked to each one. This allows us to use
the new uclass phandle functionality to implement a proper GPIO binding.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This deals with the polarity bit and selecting the correct bank device
given a GPIO number.
Signed-off-by: NSimon Glass <sjg@chromium.org>

These functions are going away, so use the new uclass support instead.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Add a new 'demo light' command which uses GPIOs to control imaginary lights.
Each light is assigned a bit number in the overall value. This provides an
example driver for using the new GPIO API.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Add a deprecation notice to each function so that it is more obvious that we
are moving GPIOs to driver model.
Signed-off-by: NSimon Glass <sjg@chromium.org>

At present U-Boot sort-of supports the standard way of reading GPIOs from
device tree nodes, but the support is incomplete, a bit clunky and only
works for GPIO bindings where #gpio-cells is 2.

Add new functions to request GPIOs, taking full account of the device
tree binding. These permit requesting a GPIO with a simple call like:

   gpio_request_by_name(dev, "cd-gpios", 0, &desc, GPIOD_IS_IN);

This will request the GPIO, looking at the device's node which might be
this, for example:

   cd-gpios = <&gpio TEGRA_GPIO(B, 3) GPIO_ACTIVE_LOW>;

The GPIO will be set to input mode in this case and polarity will be
honoured by the GPIO calls.

It is also possible to request and free a list of GPIOs.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Only the GPIO driver knows about the full GPIO device tree binding used by
a device. Add a method to allow the driver to provide this information to the
uclass, including the GPIO offset within the device and flags such as the
polarity.
Signed-off-by: NSimon Glass <sjg@chromium.org>

So far driver model's GPIO uclass just implements the existing GPIO API.
This has some limitations:

- it requires manual device tree munging to support GPIOs in device tree
    (fdtdec_get_gpio() and friends)
- it does not understand polarity
- it is somewhat slower since we must scan for the GPIO device each time
- Global GPIO numbering can change if other GPIO drivers are probed
- it requires extra steps to set the GPIO direction and value

The new functions have a dm_ prefix where necessary to avoid name conflicts
but we can remove that when it is no-longer needed. The new struct gpio_desc
holds all required information about the GPIO. For now this is intended to
be stored by the client requesting the GPIO, but in future it might be
brought into the uclass in some way.

With these changes the old GPIO API still works, and uses the driver model
API underneath.
Signed-off-by: NSimon Glass <sjg@chromium.org>

For GPIOs and other functions we want to look up a phandle and then decode
a list of arguments for that phandle. Each phandle can have a different
number of arguments, specified by a property in the target node. This is
the "#gpio-cells" property for GPIOs.

Add a function to provide this feature, taken modified from Linux 3.18.
Signed-off-by: NSimon Glass <sjg@chromium.org>

At present the tegra GPIO driver does not fully support the existing device
tree binding, but add the binding file to cover the existing partial support.
Signed-off-by: NSimon Glass <sjg@chromium.org>

At present the exynos GPIO driver does not fully support the existing device
tree binding, but add the binding file to cover the existing partial support.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Add the binding file that we are about to support.
Signed-off-by: NSimon Glass <sjg@chromium.org>

The common/board_r.c has show_model_r() to display the model name
if the DTB has a "model" property.  It sounds useful to have a similar
function in common/board_f.c too because most of the boards show
their board name before relocation.

Instead of implementing the same function in both common/board_f.c
and common/board_r.c, let's split it up into common/show_board_info.c.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: NSimon Glass <sjg@chromium.org>

To store 10bit chip address, the variable type should not be uchar,
but uint.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: NSimon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher<hs@denx.de>

Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: NSimon Glass <sjg@chromium.org>

This commit adds on-chip I2C driver used on newer SoCs of Panasonic
UniPhier platform.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NSimon Glass <sjg@chromium.org>
Acked-by: NHeiko Schocher <hs@denx.de>

This commit adds on-chip I2C driver used on some old Panasonic
UniPhier SoCs.
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NSimon Glass <sjg@chromium.org>
Acked-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NSimon Glass <sjg@chromium.org>
Acked-by: NHeiko Schocher <hs@denx.de>

This commit 904672ee (lcd: refactor lcd console stuff into its
own file), which cause lcd console address is not initialized.

This patch initialize the lcd console use the default value,
will be update when splash screen is enabled.
Signed-off-by: NBo Shen <voice.shen@atmel.com>

When build for Atmel related boards which support SPL,
it will generate boot.bin, also clean when it when do
"make clean" operation.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Acked-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

Microblaze currently doesn't use printf in SPL. So this one line was the only
reference to it and resulted in the printf functionality to be pulled in.
Exceeding the 4k size limit. Lets change the printf back to puts so that
Microblaze is fixed again. The only drawback is that the detected boot-device
number will not be printed. But this message alone should be helpful enough
to get an idea where the boot process is broken.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: NMichal Simek <michal.simek@xilinx.com>