Introduce include/environment/ti/dfu.h that
consolidates environment variable definitions
for various TI boards that support DFU today.

Tested on AM335x EVM, AM437x SK EVM and DRA74x
EVM by using DFU to write to SD card.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

ARCH_ZYNQ(MP) selects DM_USB, where CONFIG_USB_MAX_CONTROLLER_COUNT
is not used.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NMoritz Fischer <moritz.fischer@ettus.com>
Acked-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This patch adds initial support for Samtec VIN|ING 2000 board.
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: NStefano Babic <sbabic@denx.de>
Acked-by: NMarek Vasut <marex@denx.de>

Enable the escpi3 nets attached to the mikroBUS slot
on the i.MX7 Sabre evalution board. Also enble the SPI flash
commands to work with the "flash click" board.

This is V2 of this patch with changes recommended by the maintainer

CC: Jagan Teki <jteki@openedev.com>

Specify standard padding for payload to 68KB. This is derived from
the maximum header size plus maximum SPL size. It matches the
already defined offset for SD/eMMC devices (69KB) too. This allows
to use the u-boot-with-spl.imx build target to generate a directly
flashable image which can be flashed using:

  dd if=u-boot-with-spl.imx of=/dev/mmcblk0 bs=512 skip=2

While the patch has been created with SD/eMMC in mind, this also
works with other boot media. The board file needs to configure the
media specific (absolute) payload offset accordingly. Especially
the IVT offset is boot media specific and can be retrieved from the
reference manual (Table 8-25. Image Vector Table Offset and Initial
Load Region Size). For NAND boot a define like this should do the
job:

 #define CONFIG_SYS_NAND_U_BOOT_OFFS (SPL_PAD_TO + 0x400)
Signed-off-by: NStefan Agner <stefan.agner@toradex.com>

UDOO Neo Board is a development board from Seco that has three models:
 - UDOO Neo Basic
 - UDOO Neo Basic Kick Starter
 - UDOO Neo Extended
 - UDOO Neo Full

All versions are based on the i.MX6 SoloX processor.

For more details about the UDOO Neo board, please refer to:
http://www.udoo.org/udoo-neo/

This work is based on a previous commit of Francesco Montefoschi
<francesco.monte@gmail.com>:
https://github.com/fmntf/u-boot/commit/877b71184a5105e708024f232d36aed574961844

Only tested on the UDOO Neo Full board.
Signed-off-by: NBreno Lima <breno.lima@nxp.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>

Our update scripts write the kernel and device tree in seperate
UBI volumes. This allows to use a lot less UBI/UBIFS support in
U-Boot, which should lower the risk of hitting bugs in this area.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>

This commit adds basic support including:
MMC, Serial console
Signed-off-by: NSebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>

When I tried to deactivate VIDEO support for the Wandboard, it still
tried to initialize the Framebuffer and so on. That is the reason for
the added ifdefs. CONFIG_VIDEO is enabled in the configuration as default
and therefore nothing changes for the default user.

The structs mx6dl_i2c2_pad_info and mx6q_i2c2_pad_info are only available
when CONFIG_IPUV3 are set and should not be tried to access, when that
define is not defined.
Signed-off-by: NSven Ebenfeld <sven.ebenfeld@gmail.com>

To enable working efifb support, let's map the frame buffer as 32bpp
instead of 16bpp.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>

When using OF_CONTROL, the disabled value of the mini UART platdata
gets reset after board_early_init_f. So move detection and disabling
to board_init and remove board_early_init_f.
This uses the first device using the mini uart driver, as this method
works reliably with different device trees or even no device tree at all.
Signed-off-by: NFabian Vogt <fvogt@suse.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

The DFU Kconfig menu entries should be part of the SPL
Kconfig file. Also avoid using the top level Makefile by
moving the config dependent build artifacts to the driver/
and driver/usb/gadget/ Makfiles.

With that, DFU can be built again in SPL if
CONFIG_SPL_DFU_SUPPORT is enabled.

Fixes: 6ad61022 ("usb:gadget: Disallow DFU in SPL for now")
Signed-off-by: NStefan Agner <stefan.agner@toradex.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NLukasz Majewski <l.majewski@samsung.com>

NFS loading support has been added to the default environment for
most boot components, as PMMC and MON loading were added later they
did not originally get the NFS commands added, add these now.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>

The config option TARGET_K2x_EVM is set by the k2x defconfigs to pick
a board target, but the header configs also set K2x_EVM. This config
is redundant, remove it and use TARGET_K2x_EVM everywhere in its place.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>

remove now unused CONFIG_TRDX_PID_XXX
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: NStefan Agner <stefan.agner@toradex.com>
Acked-by: NMax Krummenacher <max.krummenacher@toradex.com>

Now with the config block handling in place move the U-Boot environment
location before the config block at the end of 1st "boot sector" as
deployed during production using our downstream BSP.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: NMax Krummenacher <max.krummenacher@toradex.com>

With our common code in place actually make use of it across all our
modules.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: NMax Krummenacher <max.krummenacher@toradex.com>

Set CONFIG_SYS_MMC_MAX_DEVICE to 4 for sunxi SoC.
This define is needed in the API code.
Signed-off-by: NEmmanuel Vadot <manu@bidouilliste.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

It should be 112M, to make rootfs start at 0x40000
Signed-off-by: NJacob Chen <jacob2.chen@rock-chips.com>
Acked-by: NSimon Glass <sjg@chromium.org>

At present we have a single rk3288-based Chromebook: chromebook_jerry. But
all such Chromebooks can use the same binary with only device-tree
differences. The family name is 'veyron', so rename the files accordingly.

Also update the device-tree filename since this currently differs from
Linux.
Signed-off-by: NSimon Glass <sjg@chromium.org>

rk3036 using dwc2 usb controller, need enable relate configs for it.
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Use TARGET_MPC8641HPCN from Kconfig instead.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Replace CONFIG_MPC8641 with ARCH_MPC8641 in Kconfig and clean up
existing macros.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_MPC8610HPCD from Kconfig instead.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Replace CONFIG_MPC8610 with ARCH_MPC8610 in Kconfig and clean up
existing macros.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use CONFIG_ARCH_T4240 from Kconfig instead.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use CONFIG_TARGET_T4240RDB instead.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use CONFIG_TARGET_T4240QDS instead.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use CONFIG_ARCH_T2080 and CONFIG_ARCH_T2081 instead.
Signed-off-by: NYork Sun <york.sun@nxp.com>

CONFIG_T104xRDB is defined in T104xRDB.h, so it is always enabled for
all T1040RDB, T1040D4RDB, T1042RDB, T1042D4RDB, T1042RDB_PI.
CONFIG_T104XD4RDB is defined for all T1040D4RDB, T1042D4RDB.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_T1042RDB instead.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_T1042D4RDB in Kconfig to simplify config options.
Remove macro CONFIG_T1042D4RDB.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use separated TARGET_T1042RDB_PI to simplify config options.
Remove macro CONFIG_T1042RDB_PI.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use CONFIG_TARGET_T1040RDB instead.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_T1040D4RDB in Kconfig to simplify config macros. Replace
CONFIG_T1040D4RDB with TARGET_T1040D4RDB and clean up existing macros.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Replace CONFIG_PPC_T1040 with ARCH_T1040 in Kconfig and clean up
existing macros.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Replace CONFIG_PPC_T1024 with ARCH_T1024 in Kconfig and clean up
existing macros.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Replace CONFIG_QEMU_E500 with ARCH_QEMU_E500 in Kconfig and
clean up existing macros.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Replace CONFIG_PPC_B4420 with ARCH_B4420 in Kconfig and clean up
existing macros.

Use CONFIG_TARGET_B4860QDS instead.
Signed-off-by: NYork Sun <york.sun@nxp.com>