Card detection pin is ineffective on T4240QDS Rev1.0.
There are two cards can be connected to board.
1. eMMC card is built-in board, can not be removed. so
   For eMMC card it is always there.
2. Card detecting pin is functional for SDHC card in Rev2.0.

This workaround force sdhc driver scan and initialize the card
regardless of whether the card is inserted or not in case Rev1.0.
Signed-off-by: NHaijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: NPantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

u-boot binary size for Freescale mpc85xx platforms is 512KB.
This has been reached to upper limit for some of the platforms causig
linker error.

So, Increase the u-boot binary size to 768KB.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>

This patch reverts patch 'add ft_fixup_xgec to support 3rd and 4th 10GEC'.
When dual-role MAC acts as 10G,it still uses fsl,fman-port-1g-rx/tx as before.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: NYork Sun <yorksun@freescale.com>

Rename CONFIG_PBLRCW_CONFIG and CONFIG_PBLRCW_CONFIG.

Also add their details in README.
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

- Optimize UDIMM parameters for whole range from 1500MT/s to 2140MT/s.
- Remove unused patameters: 'cpo', 'wrdata delay', '2T', which are
  unrelated to DDR3/3L.

Tested with UDIMM 9JSF25672AZ-2G1K1 and verified speed 1200/1866/2133MT/s.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Using the TPL/SPL method to booting from 8k page NAND flash.
	- Add 256kB size SRAM tlb for second step booting;
	- Add spl.c for TPL image boot;
	- Add spl_minimal.c for minimal SPL image;
	- Add C29XPCIE_NAND configure;
	- Modify C29XPCIE.h for nand config and enviroment;
Signed-off-by: NPo Liu <Po.Liu@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Using the TPL method for nand boot by sram was already
supported. Here add some code for mpc85xx ifc nand boot.

	- For ifc, elbc, esdhc, espi, all need the SPL without
	section .resetvec.
	- Use a clear function name for nand spl boot.
	- Add CONFIG_SPL_DRIVERS_MISC_SUPPORT to compile the fsl_ifc.c
	in spl/Makefile;
Signed-off-by: NPo Liu <Po.Liu@freescale.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Existing workaround only handles one RDIMM on reference design. In case
of two RDIMMs being used, the workaround requires two separate writes to
DDR_SDRAM_MD_CNTL register.

This patch also restores two debug registers changed by the workaround.
Signed-off-by: NYork Sun <yorksun@freescale.com>
CC: Ben Collins <ben.c@servergy.com>
CC: James Yang <James.Yang@freescale.com>

Unfortunately a typo presents "DDR-A003473" instead of "DDR-A003474".
Signed-off-by: NYork Sun <yorksun@freescale.com>

Enable Erratum A006379 for T2080, T2081, T4160, B4420.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

- add more serdes protocols support.
- fix some serdes lanes route.
- fix SGMII doesn't work and incorrect mdio display for XFI when serdes 0x6d.
- correct boot location info for SD/SPI boot.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Defines get_svr() for 83xx devices
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Update following DDR related settings for T1040QDS
-Correct number of chip selects to two as t1040qds supports
 two Chip selects.
-Update board_specific_parameters udimm structure with settings
 derived via calibration.
-Reduced I2C speed to 50KHz as DDR-SPD does not get reliably
 read at 400KHz.

Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 833MT/s, 1333MT/s and
1600MT/s.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Signed-off-by: NTom Rini <trini@ti.com>

The change to add 64bit initrd support broke 32bit initrd support as it
always set 64bits worth of data into the properties, even on 32bit
systems.  The fix is to use addr_cell_len (which already says how much
data is in 'tmp') to set the property, rather than always setting 8.
Thanks to Stephen Warren for pointing out the fix here.
Reported-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NTom Rini <trini@ti.com>

My original intention was to have a 100ms timeout. However, the timer
operations used return values in ms not us, so we ended up with a 100s
timeout instead. Fixing this exposes that some operations need longer
to operate than 100ms, so bump the timeout up to a whole second.
Reported-by: NAndre Heider <a.heider@gmail.com>
Reviewed-by: NAndre Heider <a.heider@gmail.com>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>

Send RPC commands to the VideoCore to turn on the SDHCI and USB modules.
For SDHCI this isn't needed in practice, since the firmware already
turned on the power in order to load U-Boot. However, it's best to be
explicit. For USB, this is necessary, since the module isn't powered
otherwise. This will allow the kernel USB driver to work.
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>

The spl directory is ignored by git as these objects are created
during spl creation.  The only file not created is the Makefile.

This file can be modified and checked in via git.

Due to the order of rule precedence having the whole directory
ignored first then indicating not to ignore the Makefile is not correct
the message to force adding the Makefile is still shown.

So reorder the .gitignore for the Makefile and indicate that the Makefile
does not need to be ignored first and then indicate everything else in spl
should be ignored after wards.
Signed-off-by: NDan Murphy <dmurphy@ti.com>

Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

The summary already has other verification. This one is not needed.

The check caused summaries to be ignored if they were not on the
numbered block. This caused problems when a summary was embedded in an
image and the image is written to a flash with bad blocks.
Signed-off-by: NCharles Manning <cdhmanning@gmail.com>

For files where we actually have extent indexes following
an extent header (ext_block->eh_depth != 0), the do/while
loop from ext4fs_get_extent_block() does not select the
proper extent index structure.

For example, if we have:

ext_block->eh_depth = 1
ext_block->eh_entries = 1
fileblock = 0
index[0].ei_block = 0

the do/while loop will exit with i set to 0 and the
ext4fs_get_extent_block() function will return 0, even if
there was a valid extent index structure following the
header.
Signed-off-by: NIonut Nicu <ioan.nicu.ext@nsn.com>
Signed-off-by: NMathias Rulf <mathias.rulf@nsn.com>

Using fs->blksz in ext4fs_get_extent_block() is not
correct since fs->blksz is not initialized on the
read path. Use EXT2_BLOCK_SIZE() instead which will
produce the desired output.
Signed-off-by: NIonut Nicu <ioan.nicu.ext@nsn.com>
Signed-off-by: NMathias Rulf <mathias.rulf@nsn.com>

Universal uses only one adapter I2C_0.
Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NPrzemyslaw Marczak <p.marczak@samsung.com>

Curently, we are using 32 bit multiplication to calculate the offset,
so the result will always be 32 bit.
This can silently cause file system corruption when performing a write
operation on partition larger than 4 GiB.

This patch address the issue by simply promoting the terms to 64 bit,
and let compilers decide how to do the multiplication efficiently.
Signed-off-by: NMa Haijun <mahaijuns@gmail.com>

It may cause file system corruption when do a write operation.
This issue only affects boards that use 32 bit lbaint_t.
Signed-off-by: NMa Haijun <mahaijuns@gmail.com>

findftd is currently setting fdtfile to undefined for the beagle c4, select omap3-beagle.dtb instead
Signed-off-by: NRobert Nelson <robertcnelson@gmail.com>

The omap_gpmc allows switching ecc at runtime. Since
the NAND_SUBPAGE_READ flag is only set, it is kept when
switching to hw ecc, which is not correct. This leads to
calling chip->ecc.read_subpage which is not a valid
pointer. Therefore clear the flag when switching ecc so
reading in hw mode works again.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: NJeroen Hofstee <jeroen@myspectrum.nl>

- Fix the path to source_file_format.txt
  - Fix a minor typo
  - Fix the type for FIT blob: it must be "flat_dt"
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>

This patch enables ethernet support in ARMv8 foundation model. The ARMv8
foundation model supports a SMSC91C111 integrated MAC and PHY module
which is present at base address 0x01A000000.

The previous implementation had enabled SMSC9115 ethernet controller
which is not present on the ARMv8 foundation model.

Tested on ARMv8 foundation model v1 and v2 by running ping/tftp
between the foundation model and the host PC via a bridged network.
Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com>

Provide default Poll Timeout value for Trats2 board.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Acked-by: NMinkyu Kang <mk7.kang@samsung.com>

Disable L2 caches for Trats and Trats2 devices.

It turns out that for data downloading with thordown command L2 cache
disablement brings a significant speed improvement.

rootfs - 400 MiB:
- L2 cache enabled:			2.69 MiB/s
- L2 cache disabled: 			5.56 MiB/s

Such improvement is possible due to reduction of the need to invalidate
redundant data, which resides in L2 cache.

Since the sent USB request size at once is 512B (L1 - 32 KiB in total) -
one can be quite confident that it is already available in L1 and L2 can
be disabled.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Acked-by: NMinkyu Kang <mk7.kang@samsung.com>

Commit 02229827 (mx6: soc: Disable VDDPU regulator) is causing kernel hang
for people using FSL kernel 3.0.35 and 3.10, so revert it for now.
Reported-by: NOtavio Salvador <otavio@ossystems.com.br>
Reported-by: NPierre Aubert <p.aubert@staubli.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

This patch adds extra dfu_alt_info entries to support storing the whole BOOT
, DATA and UMS partitions.
This allows upgrade of uImage and device tree blob (dtb) files at once.

Now it is also possible to store ext4 rootfs prepared with well established
linux tools (like mkfs.ext4).
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Acked-by: NMinkyu Kang <mk7.kang@samsung.com>

This supports SH-QSPI device on koelsch board, and enable booting from
SPI flash.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

This supports SH-QSPI device on lager board, and enable booting from
SPI flash.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reviewed-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

This adds base register address of SH QSPI.
Currently, SH QSPI is used only from R8A7790 and R8A7791.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>