- 28 7月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 27 7月, 2020 1 次提交
-
-
由 Hou Zhiqiang 提交于
Add Root Complex and Endpoint mode specific config entries, such that it's feasible to enable the RC and/or EP mode driver indepently. Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 19 5月, 2020 1 次提交
-
-
由 Kuldeep Singh 提交于
Commit 323d3af5 ("configs: ls1012ardb: Enable CONFIG_SYS_RELOC_GD_ENV_ADDR") enables the config only for LS1012ARDB. Apart from LS1012A-RDB, other platforms such as LS1012A-FRWY, LS2088A and LS1046A-RDB/FRWY also require this config to be enabled. This also helps in resolving booting crash observed in flash environment. Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 29 4月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 30 3月, 2020 1 次提交
-
-
由 Biwen Li 提交于
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1046A Signed-off-by: NBiwen Li <biwen.li@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 07 2月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 24 1月, 2020 1 次提交
-
-
由 Yinbo Zhu 提交于
Enable RTL8152, AX88179 and AX8817X USB network cards support for ls1046afrwy Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 23 1月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 05 12月, 2019 3 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Miquel Raynal 提交于
Enabling TFABOOT configuration will compile-in a call to nand_read in the boot sequence. Handle the situation by also selecting officially the raw NAND core in this case. Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
-
由 Miquel Raynal 提交于
Both symbols must be enabled when there is a raw NAND driver selected. Also enable them when CONFIG_CMD_NAND is selected to avoid breaking things when we'll further rework the MTD dependency description. Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com> [trini: Rebase and migrate a few more boards here] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 21 11月, 2019 1 次提交
-
-
由 Tom Rini 提交于
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
-
- 08 11月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 14 8月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 19 6月, 2019 1 次提交
-
-
由 Vabhav Sharma 提交于
LS1046AFRWY board supports LS1046A family SoCs. This patch add base support for this board. Board support's 4GB ddr memory, i2c, micro-click module,microSD card, serial console,qspi nor flash,ifc nand flash,qsgmii network interface, usb 3.0 and serdes interface to support two x1gen3 pcie interface. Signed-off-by: NCamelia Groza <camelia.groza@nxp.com> Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com> Signed-off-by: NPankit Garg <pankit.garg@nxp.com> Signed-off-by: NPramod Kumar <pramod.kumar_1@nxp.com> Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: NVabhav Sharma <vabhav.sharma@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
- 27 5月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Move the main symbol for Freescale Fman Ethernet controller option to Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and rename the SPIFLASH one to follow the same format as all of the others. To do this fully we need to migrate CONFIG_QC, do so. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 22 5月, 2019 2 次提交
-
-
由 Rajat Srivastava 提交于
Signed-off-by: NRajat Srivastava <rajat.srivastava@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
由 Kuldeep Singh 提交于
Update mtd-id for QSPI nor due to change introduced in mtd/spi in linux 5.0. commit 84d043185dbe ("spi: Add a driver for the Freescale/NXP QuadSPI controller") This modification is only for linux kernel version >= 5.0. To use bootargs for kernel < 5.0, use the following bootargs CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=1550000.quadspi:2m(uboot),14m(free)" CONFIG_MTDPARTS_DEFAULT="mtdparts=1550000.quadspi:2m(uboot),14m(free)" Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
- 30 4月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 03 3月, 2019 1 次提交
-
-
由 Mian Yousaf Kaukab 提交于
EFI applications need bounce buffers to work properly on these platforms. Signed-off-by: NMian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
- 18 1月, 2019 1 次提交
-
-
由 Rajesh Bhagat 提交于
update TFABOOT defconfig for SD boot on below NXP chasis2 and chasis3 platforms: ls1043a, ls1046a, ls1088a and ls2088a. Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 08 1月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 07 12月, 2018 1 次提交
-
-
由 Rajesh Bhagat 提交于
TFABOOT support includes: - ls1046ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - FMAN address changes for TFABOOT - define BOOTCOMMAND for TFABOOT Signed-off-by: NYork Sun <york.sun@nxp.com> Signed-off-by: NPankit Garg <pankit.garg@nxp.com> Signed-off-by: NVinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com>
-
- 14 11月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 25 10月, 2018 1 次提交
-
-
由 Jeremy Gebben 提交于
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: NJeremy Gebben <jgebben@sweptlaser.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 27 9月, 2018 1 次提交
-
-
由 Yinbo Zhu 提交于
This enables the folowing to Kconfig: CONFIG_BLK CONFIG_DM_MMC Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 04 9月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 18 8月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 17 8月, 2018 1 次提交
-
-
由 Tom Rini 提交于
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 27 7月, 2018 1 次提交
-
-
由 Ashish Kumar 提交于
4K erase size is used only in case of hydrid mode which is not supported on any NXP platform with flash "s25fs512s". Supported mode is uniform sector, with erase size 256kiB. Signed-off-by: NAshish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 11 7月, 2018 1 次提交
-
-
This patch moves CONFIG_MP to Kconfig Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 28 4月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: NAdam Ford <aford173@gmail.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 4月, 2018 1 次提交
-
-
由 Mario Six 提交于
Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
- 11 2月, 2018 1 次提交
-
-
由 Tom Rini 提交于
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 06 11月, 2017 1 次提交
-
-
由 Tom Rini 提交于
We move all instances of CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files. There's a few cases here where we need to expand upon what was in the header file. Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 11 10月, 2017 1 次提交
-
-
由 Tuomas Tynkkynen 提交于
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
-
- 02 9月, 2017 1 次提交
-
-
由 Tom Rini 提交于
This syncs all of the currently Kconfig'd symbols out of the headers and into the defconfig files. This has two exceptions, first am335x_evm needs to be converted to DM in SPL and then it can stop undef'ing CONFIG_DM_USB. Leaving this as-is results in a build failure, and without work, run time failure. The other case is am43xx_evm.h and in turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB host mode in SPL, but still desire to have gadget mode in U-Boot proper. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 28 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 8月, 2017 1 次提交
-
-
由 Sam Protsenko 提交于
Also introduce CONFIG_USE_BOOTARGS option so we can control if CONFIG_BOOTARGS defined at all. Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org> [trini: Resync r8a779[56]_ulcb, various ls10xx targets] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 12 8月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_PCI Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-