- 18 7月, 2006 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 14 7月, 2006 3 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
- 13 7月, 2006 2 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Bartlomiej Sieka 提交于
-
- 12 7月, 2006 3 次提交
-
-
由 Markus Klotzbuecher 提交于
Patch by Martin Krause, 20 Mar 2006 Signed-off-by: NMartin Krause <martin.krause@tqs.de>
-
由 Markus Klotzbuecher 提交于
All MII configuration is done via FEC1 registers. But MII_SPEED was configured according to FEC used. So if only FEC2 was used, this caused the real MII_SPEED register in FEC1 to stay uninitalised, what lead to "mii_send STUCK!" messages. Fix: always configure MII_SPEED on FEC1 only.
-
由 Markus Klotzbuecher 提交于
Patch by Markus Klotzbuecher, 12 Jul 2006
-
- 11 7月, 2006 3 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
Notes: - Board-dependend code for RPXLITE and RPXCLASSIC-based boards placed to the drivers/rpx_pmcia.c file to avoid duplication. Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c). - drivers/i82365.c has been split into two parts located at board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are the only boards using CONFIG_82365). - Changes were tested for clean build and *very* *few* boards.
-
- 07 7月, 2006 2 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Marian Balakowicz 提交于
Set Timer Clock Select to use CPU clock as a timer input source.
-
- 05 7月, 2006 2 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
- 04 7月, 2006 4 次提交
-
-
由 Marian Balakowicz 提交于
-
由 Marian Balakowicz 提交于
-
由 Marian Balakowicz 提交于
Enabled it for Yucca board.
-
由 Marian Balakowicz 提交于
-
- 01 7月, 2006 5 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Marian Balakowicz 提交于
-
由 Marian Balakowicz 提交于
-
由 Marian Balakowicz 提交于
-
- 30 6月, 2006 2 次提交
-
-
由 Marian Balakowicz 提交于
-
由 Marian Balakowicz 提交于
-
- 26 6月, 2006 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 20 6月, 2006 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 19 6月, 2006 3 次提交
-
-
由 Heiko Schocher 提交于
Patch from Richard Danter, 12 Aug 2005
-
-
-
- 16 6月, 2006 8 次提交
-
-
由 Wolfgang Denk 提交于
Patch by Thomas Lange, Aug 11 2005
-
由 Wolfgang Denk 提交于
Patch by Martin Krause, 8 Jun 2006 This patch supports two serial consoles on boards with a MPC5xxx CPU. The console can be switched at runtime by setting stdin, stdout and stderr to the desired serial interface (serial0 or serial1). The PSCs to be used as console port are definded by CONFIG_PSC_CONSOLE and CONFIG_PSC_CONSOLE2. See README.serial_multi for details.
-
由 Wolfgang Denk 提交于
If the bus is blocked because of a previously interrupted transfer, up to eleven clocks are generated on the I2CSCL line to complete the transfer and to free the bus. With this fix pin I2CSCL (PG6) is really configured as GPIO so the clock pulses are really generated. Patch by Martin Krause, 04 Apr 2006
-
由 Wolfgang Denk 提交于
Patch by Thomas Waehner, 07 Mar 2006
-
由 Wolfgang Denk 提交于
Patch by Martin Krause, 11 Jan 2006
-
由 Wolfgang Denk 提交于
Patch by Martin Krause, 17 Nov 2005
-
由 Wolfgang Denk 提交于
Patch by Martin Krause, 07 Nov 2005 Tested on a STK85XX baseboard. Make sure the PS/2 controller has been programmed. Jumper Settings: X66 1-2, 9-10; X61 2-3
-
由 Wolfgang Denk 提交于
Patch by Martin Krause, 08 Nov 2005 In tsc2000_read_channel() the delay after setting the multiplexer to a temperature channel is increased from 1,5 ms to 10 ms. This is to allow the multiplexer inputs to stabilize after huge steps of the input signal level.
-