Also, add other USB related config items.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

Select GPIO1 as the USB OTG ID pin for Nitrogen6x
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

desc is set at ep_enable, so for symmetry,
clear it at ep_disable.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

Since we flush the TD, we may as well set it to a known value.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

Make sure the transfer descriptor is flushed
before the queue is updated so that the controller
will not see old information.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

This controller support full and high speed.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

Change 'nfo=' to 'info='
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

This prevents a crash if tftpboot is given a bad filename.

rx_req will be released by eth_reset_config
which is called by eth_disconnect,
which is called using the .disconnect member of usb_gadget_driver by mv_pullup in mv_udc
which is called using the .pullup member of usb_gadget_ops by usb_gadget_disconnect
which is called by usb_eth_halt
which is called using the .halt member of eth_device by eth_halt
which is called by TftpHandler when TFTP_ERR_FILE_NOT_FOUND or TFTP_ERR_ACCESS_DENIED occurs

I trigger this with the following commands
setenv ipaddr 10.0.0.2 && setenv netmask 255.255.255.0 && setenv serverip 10.0.0.1
setenv usbnet_devaddr 00:11:22:33:44:55 && setenv usbnet_hostaddr 00:aa:bb:cc:dd:ee
setenv ethprime usb_ether && setenv ethact usb_ether && setenv ncip 10.0.0.1
tftpboot 10800000 10.0.0.1:missing_file
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

set wMaxPacketSize for full speed descriptors
fs_source_desc, fs_sink_desc to 64.

Full-speed bulk endpoint can have a maximum packet size of
8, 16, 32, or 64 bytes, so choice 64.

The hs_source_desc, hs_sink_desc, already have their wMaxPacketSize
set to 512. That is the only legal value for high speed bulk endpoints.

Strictly speaking, this patch is not needed because
usb_ep_autoconfig will call ep_matches which will
override wMaxPacketSize for BULK endpoints only with
the size associated with the endpoint setup by the udc driver.
But if you want to rely on this, you may as well combine the
full speed descriptor with the high speed descriptor to
minimize confusion.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

Add the call back into the board file for to enable
the SMPS10 VBUS regulator.
Signed-off-by: NDan Murphy <dmurphy@ti.com>

Add the OMAP file for the xHCI Host controller
This code will initilialize the proper components within the
OMAP5 to enable the xHCI host controller.
Signed-off-by: NDan Murphy <dmurphy@ti.com>

Add the prcm registers and the bit definitions to enable the
USB SS port of the OMAP5 device.
Signed-off-by: NDan Murphy <dmurphy@ti.com>

Add new functionality to turn on SMPS10 regulator.
This supplies the VBUS to devices connected to the
USB host ports
Signed-off-by: NDan Murphy <dmurphy@ti.com>

This patch adds a new samsung,vbus-gpio parameter to the device tree, in
preparation of replacing the currently hardcoded VBUS GPIO mechanism in
exynos5-dt.c with a device tree controlled solution, just as it already
exists in the Linux kernel.
Signed-off-by: NJulius Werner <jwerner@chromium.org>
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>

Some Exynos boards, such as the SMDK5250, control USB port power through
a GPIO pin. For now this had been hardcoded in the exynos5-dt board
file, but not all boards use the same pin, requiring local changes to
support different boards.

This patch moves the GPIO initialization into the USB host controller
drivers which they belong to, and uses the samsung,vbus-gpio parameter
in the device tree to configure it.
Signed-off-by: NJulius Werner <jwerner@chromium.org>
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>

This enables support for xHCI host controller on Exynos5
and further disables EHCI support, to make sure only one
host controller is enabled at a time, since right now
using two controllers at a time is not possible with
current usb core infrastructure.

Anyone who wants to enable EHCI support again needs to
enable CONFIG_USB_EHCI, CONFIG_USB_EHCI_EXYNOS once again
in exynos5-dt config.
Signed-off-by: NVikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>

XHCI stack driver needs this to align buffers to
CacheLine boundary. So define the same to be '64'
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>

Adding device node for xhci host controller to enable
usb 3.0 on exynos5250.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>

Adding required compatible string for xHCI host controller
as well as USB 3.0 PHY to enable dt support for usb 3.0 on
exynos5.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>

Adding methods to turn on/off power to USB3.0 type PHY
as and when required by the controller.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>

This adds driver layer for xHCI controller in Samsung's
exynos5 soc. This interacts with xHCI host controller stack.
Signed-off-by: NVikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>

This adds stack layer for eXtensible Host Controller Interface
which facilitates use of USB 3.0 in host mode.

Adapting xHCI host controller driver in linux-kernel
by Sarah Sharp to needs in u-boot.

Initial porting from Linux kernel version 3.4, with following
top commit history of drivers/usb/host/xhci* :
cf84055 xHCI: Cleanup isoc transfer ring when TD length mismatch found

This adds the basic xHCI host controller driver with bare minimum
features:
- Control/Bulk transfer support has been added with required
  infrastructure for necessary xHC data structures.
- Stream protocol hasn't been supported yet.
- No support for quirky devices has been added.
Signed-off-by: NVikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: NJulius Werner <jwerner@chromium.org>
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>

Macros defining bmRequestType field of USB device request,
given in table 9.2 USB 2.0 spec, are rather generic macros
which can be further used by other Host controller stacks.
So moving them to usb_defs header.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>

Signed-off-by: NTom Rini <trini@ti.com>

The patch:
"blackfin: Move blackfin watchdog driver out of the blackfin arch folder."
(sha1: e9a389a1)
changed hw_watchdog_init() prototype which didn't match
with Microblaze one.
This patch fixes the driver and Microblaze initialization.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This bug was introduced by:
"Add GPL-2.0+ SPDX-License-Identifier to source files"
(sha1: 1a459660)
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

commit 39ac3447 ("cmd_mtdparts: use 64
bits for flash size, partition size & offset") introduced warnings
in a couple places due to printf formats or pointer casting.

This patch fixes the warnings pointed out here:
http://lists.denx.de/pipermail/u-boot/2013-October/164981.htmlSigned-off-by: NScott Wood <scottwood@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Tom Rini <trini@ti.com>

If dout buffer is not 32 bit-aligned or data to transmit is not multiple
of 32 bit the read data pointer is already incremented on single byte reads.
Signed-off-by: NTimo Herbrecher <t.herbrecher@gateware.de>
Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>

As the spi flash transfer to multiple parts, it is forgot to add
Atmel AT25DF321 spi flash support, which broken several Atmel EK
boards which this chip. So, add it
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Reviewed-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

Added GPL-2.0+ SPDX-License-Identifier for missed spi
source files.
Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>

Added GPL-2.0+ SPDX-License-Identifier for missed sf
source files.
Signed-off-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: NBo Shen <voice.shen@atmel.com>

- Add comments.
- Renamed few macros.
- Add tabs.
Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: NBo Shen <voice.shen@atmel.com>

Unified the bank_sel calculation code for erase and
write ops.
Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>

python used in buildman doesn't need to be placed in
/usr/bin/python, So use env to ensure that the interpreter
will pick the python from environment.

Usefull with several versions of python's installed on system.
Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NTom Rini <trini@ti.com>

Pass a valid cmdtp into do_tftpb(), do_ext2load(), and do_get_fat(), to
avoid possible crashes due to null pointer dereferencing.

Commit d7884e04 does not go far enough.
There is still at least one call chain that can result in a crash.

The do_tftpb(), do_ext2load(), and do_get_fat() functions expect a valid
cmdtp.  Passing in NULL is particularly bad in the do_tftpb() case,
because eventually boot_get_kernel() will be called with a NULL cmdtp:

do_tftpb() -> netboot_common() -> bootm_maybe_autostart() -> do_bootm()
-> do_bootm_states() -> bootm_find_os() -> boot_get_kernel()

Around line 991 in cmd_bootm.c, boot_get_kernel() will dereference the
null pointer, and the board will crash.
Signed-off-by: NSteven A. Falco <stevenfalco@gmail.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>