- 24 9月, 2010 1 次提交
-
-
由 Ilya Yanok 提交于
This patch provides support for MPC8308 P1M board with the following set of features: Dual UART is supported NOR flash is supported Both TSEC Ethernet controllers are supported PCI Express initialization is supported Both I2C controllers are supported Signed-off-by: NIlya Yanok <yanok@emcraft.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 20 9月, 2010 3 次提交
-
-
由 Wolfgang Denk 提交于
Recent changes caused that the spieval board now is included in the boards built by MAKEALL, which revealed that compilation for this board has been broken for a long time: mpc5xxx_fec.c:899:2: error: #error fec->xcv_type not initialized. mpc5xxx_fec.c:899:2: error: #error fec->xcv_type not initialized. The board is orphaned. Drop support for it. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Recent changes caused that the smmaco4 board now is included in the boards built by MAKEALL, which revealed that compilation for this board has been broken for a long time: mpc5xxx_fec.c:899:2: error: #error fec->xcv_type not initialized. The board is orphaned. Drop support for it. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Recent changes caused that the HMI10 board now is included in the boards built by MAKEALL, which revealed that compilation for this board has been broken for a long time: ps2ser.c: In function 'ps2ser_init': ps2ser.c:155: error: 'UART_LCR' undeclared (first use in this function) ps2ser.c:155: error: (Each undeclared identifier is reported only once ps2ser.c:155: error: for each function it appears in.) ps2ser.c:156: error: 'UART_DLL' undeclared (first use in this function) ps2ser.c:157: error: 'UART_DLM' undeclared (first use in this function) ps2ser.c:159: error: 'UART_IER' undeclared (first use in this function) ps2ser.c:160: error: 'UART_MCR' undeclared (first use in this function) ps2ser.c:161: error: 'UART_FCR' undeclared (first use in this function) ps2ser.c:162: error: 'UART_FCR_ENABLE_FIFO' undeclared (first use in this function) ps2ser.c:166: error: 'UART_LSR' undeclared (first use in this function) ps2ser.c: In function 'ps2ser_putc': ps2ser.c:198: error: 'UART_LSR' undeclared (first use in this function) ps2ser.c:200: error: 'UART_TX' undeclared (first use in this function) ps2ser.c: In function 'ps2ser_getc_hw': ps2ser.c:224: error: 'UART_LSR' undeclared (first use in this function) ps2ser.c:225: error: 'UART_RX' undeclared (first use in this function) ps2ser.c: In function 'ps2ser_interrupt': ps2ser.c:293: error: 'UART_IIR' undeclared (first use in this function) The board is orphaned, and AFAICT has reached EOL. Drop support for it. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 13 9月, 2010 1 次提交
-
-
由 Graeme Russ 提交于
The SC520 CDP boards originally implemented by Daniel Engström are now very broken. Attempts to contact Daniel via the email address on the copyright notice have failed. Remove these boards from mainline
-
- 11 8月, 2010 1 次提交
-
-
由 Matthias Weisser 提交于
This patch adds support for the jadecpu board using the MB86R01 'Jade' SoC from Fujitsu. Signed-off-by: NMatthias Weisser <weisserm@arcor.de>
-
- 09 8月, 2010 1 次提交
-
-
由 Heiko Schocher 提交于
- nfs-options removed - hda->sda changed - mtd parts added - loadaddress changed - cmd-line length increased - lcd stuff removed - code cleanup (use I/O accessors etc.) Signed-off-by: NKlaus Heydeck <heydeck@kieback-peter.de>
-
- 02 8月, 2010 1 次提交
-
-
由 Kumar Gala 提交于
Add support for the P4080DS board, with the following features: * 36-bit only * Boots from NOR flash * FMAN drivers NOT supported * SPD DDR initialization Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: NEmil Medve <Emilian.Medve@Freescale.com> Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org> Signed-off-by: NAshish Kalra <Ashish.Kalra@freescale.com> Signed-off-by: NStuart Yoder <stuart.yoder@freescale.com> Signed-off-by: NDave Liu <daveliu@freescale.com> Signed-off-by: NLan Chunhe-B25806 <b25806@freescale.com> Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com> Signed-off-by: NTimur Tabi <timur@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com> Signed-off-by: NYork Sun <yorksun@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 18 7月, 2010 1 次提交
-
-
由 Wolfgang Denk 提交于
The board maintainer states: The GTH board is obsolete and has not been manufactured for several years. To my knowledge, no recent U-Boot build has been tested on that card. So drop support for this board. Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Thomas Lange <thomas@corelatus.se> Acked-by: Thomas Lange<thomas@corelatus.se>
-
- 16 7月, 2010 1 次提交
-
-
由 Timur Tabi 提交于
Specifics: 1) 36-bit only 2) Booting from NOR flash only 3) Environment stored in NOR flash only 4) No SPI support 5) No DIU support Signed-off-by: NTimur Tabi <timur@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 15 7月, 2010 2 次提交
-
-
由 Marek Vasut 提交于
This patch adds support for Aeronix Zipit Z2 handheld. Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
-
由 Marek Vasut 提交于
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
-
- 14 7月, 2010 1 次提交
-
-
由 Michael Hennerich 提交于
Support the new AD7160 eval board. Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 12 7月, 2010 1 次提交
-
-
由 Thomas Chou 提交于
The example configuration files of nios2-generic board can generated binary to run on the EP1C20, EP1S10, and EP1S40 boards. So the three boards can be removed. With nios2-generic approach, the fpga parameter header file can be generated from hardware designs using tools. Porting u-boot for nios2 boards is simplified. Vendors can supply their fpga parameter file or patches to add a new nios2-generic board instance. There is no need to include other boards support for nios2 in the u-boot mainline. Signed-off-by: NThomas Chou <thomas@wytron.com.tw> Signed-off-by: NScott McNutt <smcnutt@psyent.com>
-
- 10 7月, 2010 2 次提交
-
-
由 Heiko Schocher 提交于
This patch add support for the ve8313 board based on Freescale MPC8313 CPU. - serial console on UART 1 - 128 MB DDR RAM - 32 MB NOR Flash - 16 MB NAND Flash - Ethernet MII Mode over on TSEC0 - micrel ksz804 phy - Hardware WDT MAX824 changes since v1 - Environment size = sector size - use red. environment - add comments from Kim Phillips - add MAKEALL, MAINTAINERS entry - Codingstyle issues fixed - inserted original Copyrights - PCI subsys vendor ID changed from 0x1057 (Motorola) to 0x1957 (Freescale) changes since v2 - add comments from Wolfgang Denk - fix Codingstyle and some comments - reworked WDT reset (just toggling the WD_TRIG pin) - Environment size now 16KiB - fixed RAMBOOT version - fixed CONFIG_SYS_LOAD_ADDR - renamed CONFIG_TSEC1_NAME to TSEC1 Signed-off-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Ilya Yanok 提交于
This patch provides support for MPC8308RDB development board from Freescale with a minimal set of features: Dual UART is supported NOR flash is supported Both TSEC Ethernet controllers are supported PCI Express initialization is supported The following features are enabled in configuration but not fully tested: I2C (used to get the board revision) I2C-connected RTC VSC7385 switch There is one (hopefully) minor issue: on soft reset the board sometimes resets twice. I've not managed to find the fix for this problem yet. As a workaround instruction cache can be disabled. Signed-off-by: NIlya Yanok <yanok@emcraft.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 06 7月, 2010 3 次提交
-
-
由 Steve Sakoman 提交于
OMAP4 Panda is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU This patch adds basic support for booting the board. It includes i2c and mmc support. It assumes U-boot is loaded to SDRAM with the help of another small bootloader (x-load) running from SRAM. U-boot currently relies on x-load for clock, mux, and SDRAM initialization Signed-off-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Steve Sakoman 提交于
OMAP4430 SDP is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU This patch adds basic support for booting the board. It includes i2c and mmc support. It assumes U-boot is loaded to SDRAM with the help of another small bootloader (x-load) running from SRAM. U-boot currently relies on x-load for clock, mux, and SDRAM initialization Signed-off-by: NAneesh V <aneesh@ti.com> Signed-off-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Steve Sakoman 提交于
The purpose of this patch is to prepare for adding the OMAP4 architecture, which is Cortex A9 Cortex A8 and A9 both belong to the armv7 architecture, hence the name change. The two architectures are similar enough that substantial code can be shared. Signed-off-by: NAneesh V <aneesh@ti.com> Signed-off-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 05 7月, 2010 1 次提交
-
-
由 Wolfgang Denk 提交于
Fix board directory name for ML2 board, and add missing definitions for am3517_evm and s5p_goni boards. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 01 7月, 2010 1 次提交
-
-
由 Stefan Roese 提交于
This patch adds support for the T3CORP board, based on the AppliedMicro (APM) PPC460GT. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 24 6月, 2010 1 次提交
-
-
由 Wolfgang Denk 提交于
The AmigaOneG3SE board has been orphaned or a very long time, and broken for more than 12 releases resp. more than 3 years. As nobody seems to be interested any more in this stuff we may as well ged rid of it, especially as it clutters many areas of the code so it is a continuous pain for all kinds of ongoing work. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 14 6月, 2010 1 次提交
-
-
由 Wolfgang Denk 提交于
Instead of adding explicit build rules for each and every board to the top level Makefile (which makes it grow and grow), we now provide a simple default rule and extend the "mkconfig" script to read board configurations from a plain text file (table), "boards.cfg". For simple boards it is now sufficient to add a single line of text to the "boards.cfg" file, no changes to the top level Makefile are needed any more. To make the table better readable, change the notation for unused fields from "NULL" into "-". Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Mike Frysinger <vapier@gentoo.org>
-