- 07 12月, 2015 3 次提交
-
-
由 Michal Simek 提交于
Move driver to DM Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Michal Simek 提交于
Prepare for using DM. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
Calculate the minimum sd clock based on max clock. This will be done by add_sdhci() if we pass minimum clock as zero. It also does based on SD host contoller version. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 19 11月, 2015 1 次提交
-
-
由 Michal Simek 提交于
zc1571 with silicon can operate on 200MHz maximum frequency. Setup this frequency by default and fix setting for ep108. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 19 8月, 2015 1 次提交
-
-
由 Masahiro Yamada 提交于
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear away the ugly logic in include/fdtdec.h: #ifdef CONFIG_OF_CONTROL # if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL) # define OF_CONTROL 0 # else # define OF_CONTROL 1 # endif #else # define OF_CONTROL 0 #endif Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for SPL. Also, we no longer have to cancel CONFIG_OF_CONTROL in include/config_uncmd_spl.h and scripts/Makefile.spl. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Acked-by: NLinus Walleij <linus.walleij@linaro.org>
-
- 05 5月, 2015 1 次提交
-
-
由 Rob Herring 提交于
High capacity support is not a host capability, but a device capability that is queried via the OCR. The flag in the operating conditions request argument can just be set unconditionally. This matches the Linux implementation. [panto] Hand merged and renumbering MMC_MODE_DDR_52MHz. Signed-off-by: NRob Herring <robh@kernel.org> Signed-off-by: NPantelis Antoniou <pantelis.antoniou@konsulko.com> Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
-
- 29 4月, 2015 1 次提交
-
-
Remove the quirk SDHCI_QUIRK_NO_CD as it is not required. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 21 1月, 2015 1 次提交
-
-
由 Michal Simek 提交于
phys_addr_t is designed for physical addresses that's why use it. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 04 3月, 2014 1 次提交
-
-
由 Michal Simek 提交于
Enable initialize sdhci from DTB. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 07 2月, 2014 1 次提交
-
-
As per the below commit "mmc: sdhci: add the quirk for broken r1b response" (sha1: 3a638320) need to add quirk SDHCI_QUIRK_BROKEN_R1B, when the response type is R1b. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Acked-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: NPantelis Antoniou <panto@antoniou-consulting.com>
-
- 24 7月, 2013 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: NTom Rini <trini@ti.com>
-
- 30 4月, 2013 1 次提交
-
-
由 Michal Simek 提交于
Add support for SD, MMC and eMMC card on Xilinx Zynq. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NTom Rini <trini@ti.com>
-