- 17 11月, 2014 1 次提交
-
-
由 Heiko Schocher 提交于
move CONFIG_SYS_SPI_WRITE_TOUT into drivers/spi/atmel_spi.h and define a default value. Delete this define in the board config files, where it is possible (all boards use currently the same value). Signed-off-by: NHeiko Schocher <hs@denx.de> Reviewed-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 09 12月, 2013 2 次提交
-
-
由 Andreas Bießmann 提交于
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Andreas Bießmann 提交于
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com> Acked-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de> Tested-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de> Acked-by: NScott Wood <scottwood@freescale.com>
-
- 02 12月, 2013 1 次提交
-
-
由 Bo Shen 提交于
The PLLADIV2 bit is not defined in at91sam9261 SoC, so remove it. Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 05 11月, 2013 2 次提交
-
-
由 Bo Shen 提交于
Get rid of too many ifdeffery in usb ohci driver Add following two configuration for USB clock selecting - CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock - CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Rob Herring 提交于
Remove platform CONFIG_SYS_HZ definition for configs a-z*. Signed-off-by: NRob Herring <rob.herring@calxeda.com>
-
- 24 7月, 2013 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: NTom Rini <trini@ti.com>
-
- 01 9月, 2012 1 次提交
-
-
由 Rob Herring 提交于
CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present in most ARM board config files. IRQs are only enabled for 1 config, so remove the unused config options for IRQ and FIQ stack size as well. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: NRob Herring <rob.herring@calxeda.com>
-
- 21 6月, 2012 1 次提交
-
-
由 Tom Rini 提交于
We provide a default table of { 9600, 19200, 38400, 57600, 115200 } in <config_fallbacks.h> which mkconfig places after <configs/...h> in the generated config file. This is used when a board has not set its own table. Signed-off-by: NTom Rini <trini@ti.com>
-
- 27 1月, 2012 1 次提交
-
-
由 Vladimir Zapolskiy 提交于
This change follows the change by Wolfgang Grandegger (commit 6c869637), which allows to remove useless NAND_MAX_CHIPS definitions in board config files. Signed-off-by: NVladimir Zapolskiy <vz@mleia.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: NScott Wood <scottwood@freescale.com>
-
- 12 12月, 2011 1 次提交
-
-
由 Asen Dimov 提交于
The early messages can be seen on the debug console. Signed-off-by: NAsen Chavdarov Dimov <dimov@ronetix.at>
-
- 29 11月, 2011 1 次提交
-
-
由 Stelian Pop 提交于
Change my old email address which is no longer valid. Signed-off-by: NStelian Pop <stelian@popies.net> Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
- 28 11月, 2011 1 次提交
-
-
由 Stelian Pop 提交于
Change my old email address which is no longer valid. Signed-off-by: NStelian Pop <stelian@popies.net> Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
- 09 11月, 2011 1 次提交
-
-
由 Asen Dimov 提交于
Signed-off-by: NAsen Chavdarov Dimov <dimov@ronetix.at> Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
-
- 06 10月, 2011 1 次提交
-
-
由 Mike Frysinger 提交于
Now that none of the core checks CONFIG_NET_MULTI, there's not much point in boards defining it. So scrub all references to it. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 04 9月, 2011 1 次提交
-
-
由 Asen Dimov 提交于
Signed-off-by: NAsen Chavdarov Dimov <dimov@ronetix.at>
-
- 17 12月, 2010 2 次提交
-
-
由 Asen Dimov 提交于
Signed-off-by: NAsen Dimov <dimov@ronetix.at>
-
由 Asen Dimov 提交于
Signed-off-by: NAsen Dimov <dimov@ronetix.at>
-
- 30 10月, 2010 1 次提交
-
-
由 Wolfgang Denk 提交于
For ARM systems, before ELF relocation was introduced, CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the U-Boot image from whereever it was loaded to it's link address (CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation was performed at all, it was just a memcpy(). With ELF relocation, this does not work like that any more, and related boards need to be fixed anyway. So don't keep this relict any longer. Signed-off-by: NWolfgang Denk <wd@denx.de> Tested-by: NHeiko Schocher <hs@denx.de> Tested-by: NReinhard Meyer <u-boot@emk-elektronik.de>
-
- 27 10月, 2010 1 次提交
-
-
由 Wolfgang Denk 提交于
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not being able to use "sizeof(struct global_data)" in assembler files. Recent experience has shown that manual synchronization is not reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into GENERATED_GBL_DATA_SIZE which gets automatically generated by the asm-offsets tool. In the result, all definitions of this value can be deleted from the board config files. We have to make sure that all files that reference such data include the new <asm-offsets.h> file. No other changes have been done yet, but it is obvious that similar changes / simplifications can be done for other, related macro definitions as well. Signed-off-by: NWolfgang Denk <wd@denx.de> Acked-by: NKumar Gala <galak@kernel.crashing.org>
-
- 30 4月, 2010 2 次提交
-
-
由 Asen Dimov 提交于
Signed-off-by: NAsen Dimov <dimov@ronetix.at>
-
由 Asen Dimov 提交于
Signed-off-by: NAsen Dimov <dimov@ronetix.at>
-
- 17 4月, 2010 2 次提交
-
-
由 Asen Dimov 提交于
Signed-off-by: NAsen Dimov <dimov@ronetix.at>
-
由 Asen Dimov 提交于
Signed-off-by: NAsen Dimov <dimov@ronetix.at>
-
- 08 3月, 2010 1 次提交
-
-
由 Achim Ehrlich 提交于
Configuration defines should be preceeded with CONFIG_SYS_. Renamed some at91 specific defines to conform to this naming convention: AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK Signed-off-by: NAchim Ehrlich <aehrlich@taskit.de>
-
- 13 2月, 2010 2 次提交
-
-
由 Jens Scharsig 提交于
* add a real AT91 GPIO driver instead of header inline code * resolve the mixing of port and pins * change board config files to use new driver * add macros to gpio to realize backward compatibility Signed-off-by: NJens Scharsig <js_at_ng@scharsoft.de>
-
由 Jens Scharsig 提交于
* add's the new temporary CONFIG_AT91_LEGACY to all board configs This will need for backward compatiblity, while change the SoC access to c structures. If CONFIG_AT91_LEGACY is defined, the deprecated SoC is used. Signed-off-by: NJens Scharsig <js_at_ng@scharsoft.de>
-
- 09 12月, 2009 1 次提交
-
-
由 Heiko Schocher 提交于
There is more and more usage of printing 64bit values, so enable this feature generally, and delete the CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL defines. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 18 8月, 2009 1 次提交
-
-
由 Albin Tonnerre 提交于
The name of the atmel nand driver in the kernel changed from at91_nand to atmel_nand back in June 2008, but the at91-based boards config files still refer to at91_nand. This patch updates them with the new name Signed-off-by: NAlbin Tonnerre <albin.tonnerre@free-electrons.com>
-
- 22 7月, 2009 1 次提交
-
-
由 Wolfgang Denk 提交于
A large number of boards (all AT91 based) duplicated the ROUND() macro in their board specific config files. Add the definition to include/common.h and clean up the board config files. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 19 7月, 2009 1 次提交
-
-
由 Wolfgang Denk 提交于
Commit 8d2effea added a warning for configurations that use NAND without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but failed to fix the affected boards. This patch covers the non-PPC boards that were missed in the previous patch (commit 170c1972). Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 07 7月, 2009 1 次提交
-
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 21 6月, 2009 3 次提交
-
-
由 Ilko Iliev 提交于
The PM9261 board is based on the AT91SAM9261-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9261.htmlSigned-off-by: NIlko Iliev <iliev@ronetix.at> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
optimize a few the RAM init Signed-off-by: NIlko Iliev <iliev@ronetix.at> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
move PSRAM init to pm9263.c this will allow us after to make the nor lowlevel_init generic Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 13 6月, 2009 2 次提交
-
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 17 4月, 2009 2 次提交
-
-
The timer has been rewrote with a precision at ~0,18% Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Tested-by: NSergey Lapin <slapin@ossfans.org> Tested-by: NEric BENARD <ebenard@free.fr>
-
由 Ilko Iliev 提交于
The PM9263 board is based on the AT91SAM9263-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9263.htmlSigned-off-by: NIlko Iliev <iliev@ronetix.at> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-