- 19 7月, 2006 7 次提交
-
-
由 Wolfgang Denk 提交于
Patch by Martin Krause, 12 Jun 2006
-
由 Wolfgang Denk 提交于
During an automatic update via USB stick, U-Boot searches for images with the name "firmware.img" and "kernel.img". This names are now changed to "firmw_01.img" and "kernl_01.img". This is done, to prevent updates of new boards (with the new macronics "c" step flashes) with old, incompatible firmware or kernel versions. Patch by Martin Krause, 21 Jun 2006
-
由 Wolfgang Denk 提交于
Make sure upper lext pixel can be set to blue, too (so far only red was possible). Patch by Martin Krause, 15 Feb 2006
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
- increase CFG_FLASH_ERASE_TOUT from 2 to 15 seconds - use CFG_FLASH_WRITE_TOUT for programming instead of CFG_FLASH_ERASE_TOUT - remove "Unlock Bypass" mode, because macronix flashes do not support this mode officially - fix flash reset command from 0x00FF to 0x00F0. 0x00FF is only specified for Intel compatible flashes, not for AMD compatible. Patch by Martin Krause, 15 Feb 2006
-
由 Wolfgang Denk 提交于
(for erase errors and timeout errors) Patch by Martin Krause, 14 Feb 2006
-
由 Wolfgang Denk 提交于
The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module integrated in a little aluminium case. Patch by Martin Krause, 8 Jun 2006 Some code cleanup
-
- 18 7月, 2006 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 14 7月, 2006 3 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
- 13 7月, 2006 2 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Bartlomiej Sieka 提交于
-
- 12 7月, 2006 3 次提交
-
-
由 Markus Klotzbuecher 提交于
Patch by Martin Krause, 20 Mar 2006 Signed-off-by: NMartin Krause <martin.krause@tqs.de>
-
由 Markus Klotzbuecher 提交于
All MII configuration is done via FEC1 registers. But MII_SPEED was configured according to FEC used. So if only FEC2 was used, this caused the real MII_SPEED register in FEC1 to stay uninitalised, what lead to "mii_send STUCK!" messages. Fix: always configure MII_SPEED on FEC1 only.
-
由 Markus Klotzbuecher 提交于
Patch by Markus Klotzbuecher, 12 Jul 2006
-
- 11 7月, 2006 3 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
Notes: - Board-dependend code for RPXLITE and RPXCLASSIC-based boards placed to the drivers/rpx_pmcia.c file to avoid duplication. Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c). - drivers/i82365.c has been split into two parts located at board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are the only boards using CONFIG_82365). - Changes were tested for clean build and *very* *few* boards.
-
- 07 7月, 2006 2 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Marian Balakowicz 提交于
Set Timer Clock Select to use CPU clock as a timer input source.
-
- 05 7月, 2006 2 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
- 04 7月, 2006 4 次提交
-
-
由 Marian Balakowicz 提交于
-
由 Marian Balakowicz 提交于
-
由 Marian Balakowicz 提交于
Enabled it for Yucca board.
-
由 Marian Balakowicz 提交于
-
- 01 7月, 2006 5 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Marian Balakowicz 提交于
-
由 Marian Balakowicz 提交于
-
由 Marian Balakowicz 提交于
-
- 30 6月, 2006 2 次提交
-
-
由 Marian Balakowicz 提交于
-
由 Marian Balakowicz 提交于
-
- 26 6月, 2006 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 20 6月, 2006 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 19 6月, 2006 3 次提交
-
-
由 Heiko Schocher 提交于
Patch from Richard Danter, 12 Aug 2005
-
-
-
- 16 6月, 2006 1 次提交
-
-
由 Wolfgang Denk 提交于
Patch by Thomas Lange, Aug 11 2005
-