Enable CMD_GPIO for board ls1046ardb
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Enable CONFIG_NVME and CONFIG_CMD_NVME for Layerscape
platforms
Signed-off-by: NWasim Khan <wasim.khan@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

CONFIG_ENV_OVERWRITE disables write protection on various environment
variables like "ethaddr" and "serial".

Enable this config in LS1046A and LS1012A defconfigs. This resolves an
error while setting multiple values of "ethaddr" variable.

Before the change:
=> setenv ethaddr 00:E0:0C:00:06:0
=> setenv ethaddr 00:E0:0C:00:06:1
Error: Can't overwrite "ethaddr"
Error inserting "ethaddr" variable, errno=1

After the change:
=> setenv ethaddr 00:E0:0C:00:06:0
=> setenv ethaddr 00:E0:0C:00:06:1
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CONFIG_SPI_FLASH_SPANSION in defconfigs of LS1046ARDB and
LS1046AQDS which have two spansion flases i.e s25fs512s each of size
64M.
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable DM_ETH on all the defconfigs for the LS1046ARDB board.
Signed-off-by: NMadalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_PHYLIB
   CONFIG_BITBANGMII
   CONFIG_MV88E6352_SWITCH
   CONFIG_MV88E61XX_SWITCH
   CONFIG_PHYLIB_10G
   CONFIG_PHY_AQUANTIA
   CONFIG_PHY_ATHEROS
   CONFIG_PHY_BROADCOM
   CONFIG_PHY_CORTINA
   CONFIG_PHY_DAVICOM
   CONFIG_PHY_ET1011C
   CONFIG_PHY_LXT
   CONFIG_PHY_MARVELL
   CONFIG_PHY_MICREL
   CONFIG_PHY_NATSEMI
   CONFIG_PHY_REALTEK
   CONFIG_RTL8211X_PHY_FORCE_MASTER
   CONFIG_PHY_SMSC
   CONFIG_PHY_TERANETICS
   CONFIG_PHY_TI
   CONFIG_PHY_VITESSE
   CONFIG_PHY_XILINX
Signed-off-by: NTom Rini <trini@konsulko.com>

This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

setexpr command is used while running secure boot
(chain of trust with confidentiality) feature.

Enable CONFIG_CMD_SETEXPR to enable setexpr command.
Signed-off-by: NUdit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Enabling TFABOOT configuration will compile-in a call to nand_read in
the boot sequence. Handle the situation by also selecting officially
the raw NAND core in this case.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

Both symbols must be enabled when there is a raw NAND driver
selected. Also enable them when CONFIG_CMD_NAND is selected to avoid
breaking things when we'll further rework the MTD dependency
description.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com>
[trini: Rebase and migrate a few more boards here]
Signed-off-by: NTom Rini <trini@konsulko.com>

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Rename CONFIG_SECURE_BOOT to CONFIG_NXP_ESBC to avoid conflict
with UEFI secure boot.
Signed-off-by: NUdit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig.  Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.
Signed-off-by: NTom Rini <trini@konsulko.com>

Signed-off-by: NRajat Srivastava <rajat.srivastava@nxp.com>
Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

Update mtd-id for QSPI nor due to change introduced in mtd/spi in
linux 5.0. commit 84d043185dbe
  ("spi: Add a driver for the Freescale/NXP QuadSPI controller")

This modification is only for linux kernel version >= 5.0. To use
bootargs for kernel < 5.0, use the following bootargs
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0
earlycon=uart8250,mmio,0x21c0500
mtdparts=1550000.quadspi:2m(uboot),14m(free)"

CONFIG_MTDPARTS_DEFAULT="mtdparts=1550000.quadspi:2m(uboot),14m(free)"
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

EFI applications need bounce buffers to work properly on these
platforms.
Signed-off-by: NMian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1046ardb
and ls1046aqds defconfigs that missing one of them or more.
enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK
Support sata for all ls1046a defconfigs
Signed-off-by: NPeng Ma <peng.ma@nxp.com>
Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

TFABOOT support includes:
 - ls1046ardb_tfa_defconfig to be loaded by trusted firmware
 - environment address and size changes for TFABOOT
 - FMAN address changes for TFABOOT
 - define BOOTCOMMAND for TFABOOT
Signed-off-by: NYork Sun <york.sun@nxp.com>
Signed-off-by: NPankit Garg <pankit.garg@nxp.com>
Signed-off-by: NVinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.
Signed-off-by: NJeremy Gebben <jgebben@sweptlaser.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

This enables the folowing to Kconfig:
	CONFIG_BLK
	CONFIG_DM_MMC
Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_MISC_INIT_R
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: NTom Rini <trini@konsulko.com>

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.
Signed-off-by: NTom Rini <trini@konsulko.com>

4K erase size is used only in case of hydrid mode which is not
supported on any NXP platform with flash "s25fs512s".
Supported mode is uniform sector, with erase size 256kiB.
Signed-off-by: NAshish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

This patch moves CONFIG_MP to Kconfig
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Migrate the CONFIG_FSL_ESDHC option to Kconfig.
Signed-off-by: NMario Six <mario.six@gdsys.cc>