- 30 11月, 2018 6 次提交
-
-
由 Michal Simek 提交于
For testing purpose use zcu102 which has SD at controller 1 and this can be used for testing this mini configuration. U-Boot 2018.11-00279-gdc482e7ee092 (Nov 30 2018 - 10:22:56 +0100) Model: ZynqMP MINI EMMC1 Board: Xilinx ZynqMP DRAM: 512 MiB EL Level: EL3 MMC: sdhci@ff170000: 0 In: dcc Out: dcc Err: dcc ZynqMP> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
For testing purpose use zcu100 which has SD at controller 0 and this can be used for testing this mini configuration. U-Boot 2018.11-00281-gc5d48466e76e (Nov 30 2018 - 10:41:05 +0100) Model: ZynqMP MINI EMMC0 Board: Xilinx ZynqMP DRAM: 512 MiB EL Level: EL3 MMC: sdhci@ff160000: 0 In: dcc Out: dcc Err: dcc ZynqMP> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
If only usb ethernet gadget is enabled it can start automatically. If more gagdets are enabled usb ethernet gadget can be bind by "bind /amba/usb1@ff9e0000/dwc3@fe300000 usb_ether" (on zcu100) Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
This configuration is useful when you want to run small u-boot and perform DDR memory test to make sure that DDR is properly configured. It is use for board bringup because alternative u-boot memory tests is quite good. Configuration is running out of OCM. As is done for others mini configurations 0x80 bytes for variables is enough and only default variables are stored there. Alternative memtest is enabled and also 2GB of DDR via DTS files. Configuration is enabling ZYNQMP_PSU_INIT_ENABLED and include psu_init() from zcu102 for testing purpose. In case of size issue this can be moved to SPL configuration as is done for mini_qspi configuration but it is not a problem now. Log: U-Boot 2018.11-00268-gbd58b8ba8915 (Nov 29 2018 - 15:33:35 +0100) Model: ZynqMP MINI Board: Xilinx ZynqMP DRAM: WARNING: Initializing TCM overwrites TCM content 2 GiB EL Level: EL3 In: dcc Out: dcc Err: dcc ZynqMP> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There is no reason to have huge space for variables because none is using that. But there are some which are setup automatically. baudrate=115200 fdtcontroladdr=ffffa0d0 stderr=dcc stdin=dcc stdout=dcc Environment size: 72/124 bytes Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
No reason to save this data to environment. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 29 11月, 2018 12 次提交
-
-
由 Michal Simek 提交于
No reason to save additional variables to environment for mini configurations. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There is no need to waste a space for setting up bootcommand which is passed via xilinx_zynqmp.h by including "config_distro_bootcmd.h" header. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Wire up mini_qspi SPL with zcu102 for testing purpose. Normally mini u-boot runs with FSBL/SPL for certain board. Enabling SPL and configuration from zcu102 helps with testing. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There is no reason to have autoboot enabled because it should never start anything automatically. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There is no need to waste 6k if none needs it. zynq_cse_nand : all -6486 bss -20 data -136 rodata -606 text -5724 zynq_cse_nor : all -6486 bss -20 data -136 rodata -606 text -5724 Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
mtest is being checked by test/py framework and this test should run at least on one platform that's why enabling mtest on zc702. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
These symlinks are here only for testing purpose where SPL is used for soc configuration. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
If there are more instances of si570 clock-output-names property should be used for differentiation of clock output. The patch is adding this optional properties for all zynqmp boards with si570 chip. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
This chip is on the board but handling should be done via firmware not via Linux driver. Changing status property to keep it in the tree to describe it instead of removing this node completely. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Add missing clocks property. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Enable reading tx and rx buswidth from DT via spi-uclass. To get these from uclass spi-flash compatible string has to be added to flash node. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
DC4 board has qspi on it hence define and enable qspi node for it. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 26 11月, 2018 13 次提交
-
-
由 Michal Simek 提交于
BSS section was all the time separated for SPL but this symbol wasn't enabled. It is necessary to have it enabled for OF_SEPARATE configuration where DTB is appended to u-boot with DTB. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Show information about board read from DT by default to know what board U-Boot is running at. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
The standard function is less error prone than custom one. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Make sense to add controller ID to model name to have it visible through the logs to know which controller is used by which configuration. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There is no reason to enable these commands for mini configurations. It saves some space: aarch64: (for 2/2 boards) all -19076.0 bss -1048.0 data -1720.0 rodata -3840.0 text -12468.0 xilinx_zynqmp_mini_emmc1: all -19076 bss -1048 data -1720 rodata -3840 text -12468 xilinx_zynqmp_mini_emmc0: all -19076 bss -1048 data -1720 rodata -3840 text -12468 Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
U-Boot is growing that's why not needed features can be disabled: - CMDLINE_EDITING - AUTO_COMPLETE - SYS_LONGHELP Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Intention of CSE targets is not boot anything that's why also bootdelay is not necessary Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
cse targets shouldn't never have distro default enabled because these targets are not designed for booting images. It was enabled by: "configs: Re-sync with CONFIG_DISTRO_DEFAULTS" (sha1: fa2c1467) Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
If SYS_LONGHELP is disabled the following warning is generated: board/xilinx/zynq/cmds.c:496:13: warning: ‘zynq_help_text’ defined but not used [-Wunused-variable] Normal way for fixing this is to guard the whole variable. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Martin Lund 提交于
Add support for disabling subpage write support via CONFIG_SYS_NAND_NO_SUBPAGE_WRITE. Currently the Linux Arasan driver does not support subpage writes and in case of running UBI and accessing the same UBI volume from both U-Boot and Linux it is required to have the same subpage write configuration else the location of the UBI headers (EC + VID) will be misaligned (subpage vs page) and incompatible. Hence the need for disabling subpage write support in the U-Boot Arasan NAND driver. Signed-off-by: NMartin Lund <malu@gomspace.com> Acked-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
spi-rx-bus-width property is part of flash, so it should be moved to flash node from qspi node. This patch fixes the incorrect read of spi-rx-bus-width property by moving it to flash node. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
The VCU disable bit(8) in IP disable register of efuse is valid only if PL powered up and hence PL powerup status has to be considered while determining the CG part also. This patch considers the PL powerup status and ignores the VCU disable bit if PL not powered up. This fixes the issue of "unknown" id for CG parts if PL not powered up and VCU bit(8) is not set. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 24 11月, 2018 1 次提交
-
-
git://git.denx.de/u-boot-dm由 Tom Rini 提交于
Various minor sandbox improvements Better buildman warning handling Misc other things
-
- 21 11月, 2018 8 次提交
-
-
由 Simon Glass 提交于
It is useful to obtain the block-protect setting of the SPI flash, so we know whether it is fully open or (perhaps partially) write-protected. Add a method for this. Update the sandbox driver to process this operation and add a test. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
The current test is a functional test, covering all the way from the command line to the sandbox SPI driver. This is useful, but it is easier to diagnose failures with a smaller test. Add a simple test which reads and writes data and checks that it is stored and retrieved correctly. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
At present these functions return 0 on success. For some devices we want to know how many bytes were transferred. It seems useful to adjust the API to be more like the POSIX read() and write() functions. Update these two methods, a test and all users. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NPatrick Delaunay <patrick.delaunay@st.com>
-
由 Simon Glass 提交于
At present the config header is not included in this file, but it does use a CONFIG option. Fix it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
It is useful to be able to invert the colours in some cases so that the text matches the background colour. Add a parameter to the function to support this. It is strange that function takes a private data structure from another driver as an argument. It seems better to pass the device and have the function internally work out how to find its required information. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
At present, stripped files don't have the right pathname which means that blob compression cannot be used. Fix this. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This comma is not needed. Drop it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
When the build fails due to something wrong in binman it is sometimes useful to get a full backtrace showing the location of the failure. Add a BINMAN_DEBUG environment variable to support this along with some documentation. Signed-off-by: NSimon Glass <sjg@chromium.org>
-