- 07 9月, 2008 8 次提交
-
-
由 Kumar Gala 提交于
Adds returning an error from the ramdisk detection code if its not a real ramdisk (invalid). There is no reason we can't just return back to the console if we detect an invalid ramdisk or CRC error. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Anatolij Gustschin 提交于
This patch adds bootm_start() return value check. If error status is returned, we do not proceed further to prevent board reset or crash as we still can recover at this point. Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Andrew Dyer 提交于
rearrange some #if !defined() / #else / #endif statements to remove the negative logic. Signed-off-by: NAndrew Dyer <adyer@righthandtech.com>
-
由 Kyungmin Park 提交于
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
-
由 Heiko Schocher 提交于
I didn't try to use drivers/mtd/nand/fsl_upm.c for the NAND driver, because I have no longer access to the hardware. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
Fix compile problems caused by commit cfa460adSigned-off-by: NHeiko Schocher <hs@denx.de>
-
由 Kyungmin Park 提交于
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
-
由 Mark Jackson 提交于
Added new CONFIG_DISABLE_CONSOLE define and GD_FLG_DISABLE_CONSOLE. When CONFIG_DISABLE_CONSOLE is defined, setting GD_FLG_DISABLE_CONSOLE disables all console input and output. Signed-off-by: NMark Jackson <mpfj@mimc.co.uk>
-
- 06 9月, 2008 3 次提交
-
-
由 Ricardo Ribalda Delgado 提交于
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@uam.es>
-
由 Yuri Tikhonov 提交于
Some of multi-function USB controllers (e.g. ISP1562) allow root hub resetting only via EHCI registers. So, this patch adds the corresponding kind of reset to OHCI's hc_reset() if the newly introduced CONFIG_PCI_EHCI_DEVNO option is set (e.g. for Socrates board). Signed-off-by: NYuri Tikhonov <yur@emcraft.com> Acked-by: NMarkus Klotzbuecher <mk@denx.de>
-
由 Yuri Tikhonov 提交于
Signed-off-by: NYuri Tikhonov <yur@emcraft.com>
-
- 05 9月, 2008 1 次提交
-
-
由 Stefan Roese 提交于
This patch fixes a problem spotted on Glacier/Canyonlands (and most likely lots of other board ports), that no serial output was seen after console initialization in console_init_r(). This is because the last added console device was used instead of the first added. This patch fixes this problem by using list_add_tail() instead of list_add() to register a device. This way the first added console is used again. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 04 9月, 2008 12 次提交
-
-
-
-
由 Nick Spence 提交于
and add mpc8313 NAND build to MAKEALL Signed-off-by: NNick Spence <nick.spence@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
-
由 Nick Spence 提交于
Cleans up some latent issues with the data cache control so that dcache_enable() and dcache_disable() will work reliably (after unlock_ram_in_cache() has been called) Signed-off-by: NNick Spence <nick.spence@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Nick Spence 提交于
Record the Arbiter Event Register values and optionally display them. The Arbiter Event Register can record the type and effective address of an arbiter error, even through an HRESET. This patch stores the values in the global data structure. Display of the Arbiter Event registers immediately after the RSR value can be enabled with defines. The Arbiter values will only be displayed if an arbiter event has occured since the last Power On Reset, and either of the following defines exist: #define CONFIG_DISPLAY_AER_BRIEF - display only the arbiter address and and type register values #define CONFIG_DISPLAY_AER_FULL - display and interpret the arbiter event register values Address Only transactions are one of the trapped events that can register as an arbiter event. They occur with some cache manipulation instructions if the HID0_ABE (Address Broadcast Enable) is set and the memory region has the MEMORY_COHERENCE WIMG bit set. Setting: #define CONFIG_MASK_AER_AO - prevents the arbiter from recording address only events, so that it can still capture other real problems. Signed-off-by: NNick Spence <nick.spence@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Nick Spence 提交于
This is needed in unlock_ram_in_cache() because it is called from C and will corrupt the small data area anchor that is kept in R2. lock_ram_in_cache() is modified similarly as good coding practice, but is not called from C. Signed-off-by: NNick Spence <nick.spence@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Nick Spence 提交于
Set DAT value before DIR values to avoid creating glitches on the GPIO signals. Set gpio level register before direction register to inhibit glitches on high level output pins. Dir and data gets cleared at powerup, so high level output lines see a short low pulse between setting the direction and level registers. Issue was seen on a new board with the nReset line of the NOR flash connected to a GPIO. Setting the direction register puts the NOR flash in reset so the next instruction to set the level cannot get executed. Signed-off-by: NNick Spence <nick.spence@freescale.com> Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
-
git://git.denx.de/u-boot-ppc4xx由 Wolfgang Denk 提交于
Conflicts: board/esd/dasa_sim/dasa_sim.c Signed-off-by: NWolfgang Denk <wd@denx.de>
-
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 03 9月, 2008 16 次提交
-
-
由 Matthias Fuchs 提交于
This patch adds initdram() to DASA_SIM boards that has been removed accidentally by a previous commit. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch removes some direct references to common/lists.o from some esd linker scripts. This is necessary because the lists source was moved and is not in the "common" directory anymore. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
This patch removes initdram() and testdram() from most esd 405 platforms. Some boards also have an empty dummy implementation of misc_init_f(). This is also removed. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
- remove PCI code - add command line editing - minor cleanup Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
This patch removed the obsolete initdram() function from VOM405 platform file. Some minor cleanup. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
Signed-off-by: NMatthias Fuchs <mf@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
Wrap long lines etc. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
This patch enables the PCI-OHCI controller on PLU405 board. Also the default CPU frequency is updated to 266 MHz and command line editing is enabled. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
This patch - wraps some long lines - removes unused/obsolete functions: misc_init_f() and initdram() Signed-off-by: NMatthias Fuchs <mf@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
Signed-off-by: NMatthias Fuchs <mf@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
Signed-off-by: NMatthias Fuchs <mf@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
Signed-off-by: NMatthias Fuchs <mf@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Jochen Friedrich 提交于
If a board has a variable number of flash banks, there are empty entries in flash_info[] and CFG_DIRECT_FLASH_TFTP is set, tftp boot fails with "Outside available Flash". This patch skips flash banks with unknown flash ids. Signed-off-by: NJochen Friedrich <jochen@scram.de> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Nobuhiro Iwamatsu 提交于
The RSK7203 board has the SMSC9118 wired up 'incorrectly'. Byte-swapping is necessary, and so poor performance is inevitable. This problem cannot evade by the swap function of CHIP, this can evade by software Byte-swapping. And this has problem by FIFO access only. pkt_data_pull/pkt_data_push functions necessary to solve this problem. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Ben Warren 提交于
Affected boards: db64360 db64460 katmai taihu taishan yucca cpc45 cpu87 eXalion elppc debris kvme080 mpc8315erdb integratorap ixdp425 oxc pm826 pm828 pm854 pm856 ppmc7xx sc3 sc520_spunk sorcery tqm8272 tqm85xx utx8245 Removed initialization of the driver from net/eth.c Also, wrapped contents of pci_eth_init() by CONFIG_PCI. Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-