- 27 3月, 2008 12 次提交
-
-
由 Anatolij Gustschin 提交于
This patch fixes compilation error cmd_usb.c: In function 'do_usb': cmd_usb.c:552: error: void value not ignored as it ought to be Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Timur Tabi 提交于
Add support to the Freescale I2C driver (fsl_i2c.c) for setting and querying the I2C bus speed. Current 8[356]xx boards define the CFG_I2C_SPEED macro, but fsl_i2c.c ignores it and uses conservative value when programming the I2C bus speed. Signed-off-by: NTimur Tabi <timur@freescale.com> Acked-by: NAndy Fleming <afleming@freescale.com>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Dave Liu 提交于
Add the Freescale on-chip SATA controller driver to u-boot, The SATA controller is used on the 837x and 8315 targets, The driver can be used to load kernel, fs and dtb. The features list: - 1.5/3 Gbps link speed - LBA48, LBA28 support - DMA and FPDMA support - Two ports support Signed-off-by: NDave Liu <daveliu@freescale.com>
-
由 Dave Liu 提交于
Signed-off-by: NDave Liu <daveliu@freescale.com>
-
由 Dave Liu 提交于
Signed-off-by: NDave Liu <daveliu@freescale.com>
-
由 Dave Liu 提交于
Signed-off-by: NDave Liu <daveliu@freescale.com>
-
由 Dave Liu 提交于
add simple libata support in u-boot Signed-off-by: NDave Liu <daveliu@freescale.com>
-
由 Dave Liu 提交于
original ata_piix driver is using IDE framework, not real SATA framework. For now, the ata_piix driver is only used by x86 sc520_cdp board. This patch makes the ata_piix driver use the new SATA framework, so - remove the duplicated command stuff - remove the CONFIG_CMD_IDE define in the sc520_cdp.h - add the CONFIG_CMD_SATA define to sc520_cdp.h Signed-off-by: NDave Liu <daveliu@freescale.com>
-
由 Dave Liu 提交于
- add the SATA framework - add the SATA command line Signed-off-by: NDave Liu <daveliu@freescale.com>
-
由 Dave Liu 提交于
move the sata.h from include/ to drivers/block/ata_piix.h Signed-off-by: NDave Liu <daveliu@freescale.com>
-
由 Dave Liu 提交于
move the cmd_sata.c from common/ to drivers/ata_piix.c, the cmd_sata.c have some part of ata_piix controller drivers. consolidate the driver to have better framework. Signed-off-by: NDave Liu <daveliu@freescale.com>
-
- 26 3月, 2008 28 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Joakim Tjernlund 提交于
The default settings for RTC DS1337 keeps the OSC output, 32,768 Hz, on. This add CFG_RTC_DS1337_NOOSC to turn it off. Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
git://www.denx.de/git/u-boot-testing由 Bartlomiej Sieka 提交于
Conflicts: common/cmd_bootm.c cpu/mpc8xx/cpu.c Signed-off-by: NBartlomiej Sieka <tur@semihalf.com>
-
由 Aras Vaichas 提交于
This patch changes the "usb storage" command to return success if it finds a USB storage device, otherwise it returns error. Signed-off-by: NMarkus Klotzbuecher <mk@denx.de>
-
由 Anton Vorontsov 提交于
Linux understands "host" (default), "peripheral" and "otg" (broken). Though, U-Boot doesn't restrict dr_mode variable to these values (think of renames in future). Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Anton Vorontsov 提交于
RTL8211B sets link state register after autonegotiation complete, so with bootdelay=0 RTL8211B will report lack of the link. To fix this, we should wait for aneg to complete, even if the link is currently down. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Anton Vorontsov 提交于
device_type = "soc" is being deprecated, newer device trees will use "fsl,soc" and/or "fsl,immr" for the soc nodes. This patch also adds clock-frequency property for soc nodes (the same value as bus-frequency). Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Joe D'Abbraccio 提交于
With the original value of 1/2 clock cycle delay, the system ran relatively stable except when we run benchmarks that are intensive users of memory. When I run samba connected disk with a HDBENCH test, the system locks-up or reboots sporadically. Signed-off by: Joe D'Abbraccio <Joe.D'abbraccio@freescale.com>
-
由 Scott Wood 提交于
The device trees for these boards describe PCI I/O as starting from address zero from the device's perspective. Placing I/O elsewhere may cause problems with certain PCI boards, and may cause problems with Linux. Signed-off-by: NScott Wood <scottwood@freescale.com>
-
由 Anton Vorontsov 提交于
At least on the "33MHz Pilot" board crystal is actually 33.3MHz. This patch fixes "system time drifting" problem. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
This is needed to update /choosen/linux,stdout-path properly. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
Plus modify environment to use it and remove bootfile env variable, it is internal and CONFIG_BOOTFILE is used for these purposes. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
Current DDR setup easily causes memory corruption, this patch fixes it. Also fix TIMING_CFG0_MRS_CYC definition. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
This patch adds qe pario pins configuration for AD7843 ADC/Touchscreen controller and FHCI (QE USB). Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
This is needed for BCM PHYs to work on this board. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
This patch adds basic support for Broadcom BCM5481 PHY. RXD-RXC delay quirk comes from MPC8360E-RDK BSP source, author is Peter Barada <peterb@logicpd.com>. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
PHY drivers will use it to setup software delay between RXD and RXC signals. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
This is primarily for the early console support. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
On the MPC8377ERDB: 2 SATA and 2 PCI-E. On the MPC8378ERDB: 2 PCI-E On the MPC8379ERDB: 4 SATA Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
This patch adds few routines to configure serdes on 837x targets. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
..plus get rid of some #ifdefs in the .c files. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Anton Vorontsov 提交于
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
-
由 Jerry Van Baren 提交于
Signed-off-by: NGerald Van Baren <vanbaren@cideas.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-