- 15 5月, 2021 4 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
-
https://source.denx.de/u-boot/custodians/u-boot-amlogic由 Tom Rini 提交于
- dts: add missing -u-boot.dtsi to enable HDMI on Beelink GTKing/King-Pro - usb: dwc3-meson-g12a: skip phy on -ENODATA aswell - net: dwmac_meson8b: do not set TX delay in TXID & RXID - net: designware: meson8b: add g12a compatible
-
-
- 14 5月, 2021 28 次提交
-
-
由 Neil Armstrong 提交于
Add support for the Meson G12A dwmac glue compatible needed after Linux 5.12 sync. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Neil Armstrong 提交于
When the PHY interface is set as TXID & RXID, the delays should be taken from DT, but first they should not be hardcoded since the PHY driver will set them. Fixes: 798424e8 ("net: designware: add Amlogic Meson8b & later glue driver") Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com> Reviewed-by: NRamon Fried <rfried.dev@gmail.com>
-
由 Neil Armstrong 提交于
If the PHY isn't specified in the DT, -ENODATA means it should be skipped, handle it like -ENOENT. With that, devices without USB3 supported can have USB working (Odroid-HC4). Fixes: adb049ab ("usb: dwc3: Add Meson G12A USB Glue") Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Neil Armstrong 提交于
This lacks the right u-boot specific DT include to make HDMI work. Reported-by: NB1oHazard <ty3uk@mail.ua> Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Bin Meng 提交于
This reverts commit bc8bbb77. This commit breaks U-Boot booting on SiFive Unleashed board, as there is no such CSR on U54 core. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NLeo Yu-Chi Liang <ycliang@andestech.com>
-
由 Vincent Chen 提交于
The pwm_sifive_set_config() and pwm_sifive_set_enable() cannot work properly due to the wrong implementations. It will cause the u-boot PWM command to not work as expected. The bugs will be resolved in this patch. Signed-off-by: NVincent Chen <vincent.chen@sifive.com> Reviewed-by: NRick Chen <rick@andestech.com>
-
由 Sean Anderson 提交于
It is no longer necessary to disallow ai ram, since it is enabled by the sram driver. Signed-off-by: NSean Anderson <seanga2@gmail.com>
-
由 Sean Anderson 提交于
Testing showed that disabling AI while leaving PLL1 enabled disabled the aisram. This suggests that AI is a more appropriate clock for that ram bank. Signed-off-by: NSean Anderson <seanga2@gmail.com>
-
由 Sean Anderson 提交于
This is more consistent with the naming of other ram banks, and matches what Linux is doing. Reported-by: NDamien Le Moal <Damien.LeMoal@wdc.com> Signed-off-by: NSean Anderson <seanga2@gmail.com>
-
由 Sean Anderson 提交于
We just need to initialize all the clocks pre-reloc. The clock driver creates a bunch of devices, so we need to increase the pre-reloc malloc arena. Signed-off-by: NSean Anderson <seanga2@gmail.com>
-
由 Sean Anderson 提交于
These devices are necessary for the clock driver, which is required by the sram driver, to run pre-relocation. Signed-off-by: NSean Anderson <seanga2@gmail.com>
-
由 Sean Anderson 提交于
Variables which had previously been stored in .bss are moved to .data. In addition, probed needs to be reset when the clock driver is re-bound post-relocation. Signed-off-by: NSean Anderson <seanga2@gmail.com>
-
由 Sean Anderson 提交于
No other (real) clocks have the cpu clock as their parent; instead they are children of aclk. Move the clint clock under aclk to match them. Signed-off-by: NSean Anderson <seanga2@gmail.com>
-
由 Sean Anderson 提交于
This simplifies the PLL creation process, since we don't have to pass all the parameters individually. Signed-off-by: NSean Anderson <seanga2@gmail.com>
-
由 Sean Anderson 提交于
This conditional always evaluated as false, regardless of the value of reg. Fix it so that it properly tests the bits in the PLL register. Also test PLL_EN, now that we set it. Reported-by: NDamien Le Moal <Damien.LeMoal@wdc.com> Signed-off-by: NSean Anderson <seanga2@gmail.com>
-
由 Sean Anderson 提交于
After starting or setting the rate of a PLL, the enable bit must be set. This fixes a bug where the AI ram would not be accessible, because it requires PLL1 to be running. Signed-off-by: NSean Anderson <seanga2@gmail.com> Reviewed-by: NDamien Le Moal <damien.lemoal@wdc.com>
-
由 Sean Anderson 提交于
If the user/dev explicitly requests a clock be assigned a certain rate, then we should warn them if we can't do it. This makes it clear if the clock is running at the default rate. Signed-off-by: NSean Anderson <seanga2@gmail.com>
-
由 Rick Chen 提交于
Add Leo as co-maintainer for RISC-V. Signed-off-by: NRick Chen <rick@andestech.com>
-
由 Tom Rini 提交于
- Improve support for various forms of extension boards and add DT overlay application support.
-
由 Kory Maincent 提交于
Update the Kconfig and the board file to make the am335x board compatible with cape detection. Signed-off-by: NKory Maincent <kory.maincent@bootlin.com>
-
由 Kory Maincent 提交于
The am335x from BeagleBone use i2c EEPROM to detect capes. The memory is wired to i2c bus 2 therefore it need to be enabled. Add i2c2 clock, pinmux description and pinmux enable function. Signed-off-by: NKory Maincent <kory.maincent@bootlin.com>
-
由 Kory Maincent 提交于
This commit enables using the extension board detection mechanism on CHIP boards Signed-off-by: NKory Maincent <kory.maincent@bootlin.com> Acked-by: NMaxime Ripard <maxime@cerno.tech> Acked-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Kory Maincent 提交于
Add the extension_board_scan specific function to scan the information of the EEPROM on one-wire and fill the extension struct. Add the Kconfig symbol to enable the needs to detect DIPs. Signed-off-by: NKory Maincent <kory.maincent@bootlin.com> Reviewed-by: NMaxime Ripard <maxime@cerno.tech> Acked-by: NAndre Przywara <andre.przywara@arm.com>
-
由 Kory Maincent 提交于
This patch changes the functioning of the detection of w1 devices. The old way was a comparison between detected w1 and the ones described in the device tree. Now it will just look for the driver matching the family id of the w1 detected. The patch is inspired from Maxime Ripard code. Signed-off-by: NKory Maincent <kory.maincent@bootlin.com> Reviewed-by: NMaxime Ripard <maxime@cerno.tech>
-
由 Kory Maincent 提交于
This commit enables using the extension board detection mechanism on AM57xx based platforms. Signed-off-by: NKory Maincent <kory.maincent@bootlin.com>
-
由 Kory Maincent 提交于
The BeagleBone platforms all use a common mechanism to discover and identify extension boards (called "capes"): each extension board has an I2C-connected EEPROM describing itself. This patch implements a generic extension_scan_board() feature that can be used by all BeagleBone platforms to read those I2C EEPROMs and fill in the list of "extension" structures. Following commits will enable this common logic on two BeagleBone platforms. Signed-off-by: NKory Maincent <kory.maincent@bootlin.com>
-
由 Kory Maincent 提交于
This commit extends the sandbox to implement a dummy extension_board_scan() function and enables the extension command in the sandbox configuration. It then adds a test that checks the proper functionality of the extension command by applying two Device Tree overlays to the sandbox Device Tree. Signed-off-by: NKory Maincent <kory.maincent@bootlin.com> [trini: Limit to running on sandbox] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Kory Maincent 提交于
This patch adds a new "extension" command, which aims at detecting extension boards connected to the hardware platform, and apply the Device Tree overlays that describe the hardware present on those extension boards. In order to enable this mechanism, board-specific code must implement the extension_board_scan() function that fills in a linked list of "struct extension", each describing one extension board. In addition, the board-specific code must select the SUPPORT_EXTENSION_SCAN Kconfig boolean. Based on this: - "extension scan" makes the generic code call the board-specific extension_board_scan() function to retrieve the list of detected extension boards. - "extension list" allows to list the detected extension boards. - "extension apply <number>|all" allows to apply the Device Tree overlay(s) corresponding to one, or all, extension boards The latter requires two environment variables to exist and set one variable to run: - extension_overlay_addr: the RAM address where to load the Device Tree overlays - extension_overlay_cmd: the U-Boot command to load one overlay. Indeed, the location and mechanism to load DT overlays is very setup specific. - extension_overlay_name: set by the command: the name of the DT which will be load during the execution. When calling the command described in the extension_overlay_cmd variable, the variable extension_overlay_name will be defined. So a typical extension_overlay_cmd will look like this: extension_overlay_cmd=load mmc 0:1 $extension_overlay_addr /boot/$extension_overlay_name Here is an example on how to use it: => run loadfdt => fdt addr $fdtaddr => setenv extension_overlay_addr 0x1000 => setenv extension_overlay_cmd 'load mmc 0:1 ${extension_overlay_addr} /boot/${extension_overlay_name}' => extension scan Found 1 extension board(s). => extension apply 0 519 bytes read in 3 ms (168.9 KiB/s) Signed-off-by: NKory Maincent <kory.maincent@bootlin.com> Reviewed-by: NMaxime Ripard <maxime@cerno.tech>
-
- 13 5月, 2021 3 次提交
-
-
由 Kory Maincent 提交于
Move the fdt_valid function to fdt_support. This changes allow to be able to test the validity of a devicetree in other c files. Update code syntax. Signed-off-by: NKory Maincent <kory.maincent@bootlin.com> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NMaxime Ripard <maxime@cerno.tech>
-
由 Marek Vasut 提交于
Scrub duplicate /memory@* node entries here. Some R-Car DTs might contain multiple /memory@* nodes, however fdt_fixup_memory_banks() either generates single /memory node or updates the first /memory node. Any remaining memory nodes are thus potential duplicates. However, it is not possible to delete all the memory nodes right away, since some of those might not be DRAM memory nodes, but some sort of other memory. Thus, delete only the memory nodes which are in the R-Car3 DBSC ranges. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
-
由 Marek Vasut 提交于
The rcar-common/common.c contains various common board functions shared by all R-Car and RZG boards. This board is not compiling the file in, so add it. This way, part of the board code can be de-duplicated too. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Adam Ford <aford173@gmail.com>
-
- 12 5月, 2021 5 次提交
-
-
https://source.denx.de/u-boot/custodians/u-boot-ti由 Tom Rini 提交于
- Initial support for AM64 EVM and SK - K3 DDR driver unification for J7 and AM64 platforms. - Minor fixes for TI clock driver
-
由 Vignesh Raghavendra 提交于
Add CPSW related nodes for AM642 SK. There are two CPSW ports on the board but U-Boot supports only the first port. Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
-
由 Vignesh Raghavendra 提交于
AM64 as CPSW3G IP with 2 external ports. Add DT entries for the same (based on kernel DT). Disable second port as its by default set to ICSS usage on EVM. Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
-
由 Vignesh Raghavendra 提交于
Add a new compatible to support AM64 SoC Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
-
由 Vignesh Raghavendra 提交于
Currently driver may end up caching disabled port ID as active interface. Fix this by bailing out earlier in case port is marked disabled in the DT. Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
-