- 10 4月, 2019 16 次提交
-
-
由 Marek Vasut 提交于
Add option to the mmc rd test to check the duration of the execution of the mmc read command. This allows intercepting read performance regressions. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Marek Vasut 提交于
Add test for 'mmc info' subcommand. This tests whether the card information is obtained correctly and verifies the device, bus speed, bus mode and bus width. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Marek Vasut 提交于
Add test for 'mmc rescan' subcommand. This tests whether the system can switch to a specific card and then rescan the card. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Marek Vasut 提交于
Add separate test for 'mmc dev' subcommand. This tests whether the system can switch to a specific card. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Marek Vasut 提交于
Factor out the 'mmc dev' call so it can be recycled by other tests. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Anssi Hannula 提交于
A FAT12/FAT16 root directory location is specified by a sector offset and it might not start at a cluster boundary. It also resides before the data area (before cluster 2). However, the current code assumes that the root directory is located at a beginning of a cluster, causing no files to be found if that is not the case. Since the FAT12/FAT16 root directory is located before the data area and is not aligned to clusters, using unsigned cluster numbers to refer to the root directory does not work well (the "cluster number" may be negative, and even allowing it be signed would not make it properly aligned). Modify the code to not use the normal cluster numbering when referring to the root directory of FAT12/FAT16 and instead use a cluster-sized offsets counted from the root directory start sector. This is a relatively common case as at least the filesystem formatter on Win7 seems to create such filesystems by default on 2GB USB sticks when "FAT" is selected (cluster size 64 sectors, rootdir size 32 sectors, rootdir starts at half a cluster before cluster 2). dosfstools mkfs.vfat does not seem to create affected filesystems. Signed-off-by: NAnssi Hannula <anssi.hannula@bitwise.fi> Reviewed-by: NBernhard Messerklinger <bernhard.messerklinger@br-automation.com> Tested-by: NBernhard Messerklinger <bernhard.messerklinger@br-automation.com>
-
由 Gero Schumacher 提交于
Hi, when I try to load a sparse file via ext4load, I am getting the error message 'invalid extent' After a deeper look in the code, it seems to be an issue in the function ext4fs_get_extent_block in fs/ext4/ext4_common.c: The file starts with 1k of zeros. The blocksize is 1024. So the first extend block contains the following information: eh_entries: 1 eh_depth: 1 ei_block 1 When the upper layer (ext4fs_read_file) asks for fileblock 0, we are running in the 'invalid extent' error message. For me it seems, that the code is not prepared for handling a sparse block at the beginning of the file. The following change, solved my problem: I am really not an expert in ext4 filesystems. Can somebody please have a look at this issue and give me a feedback, if I am totally wrong or not?
-
由 Jean-Jacques Hiblot 提交于
Test cases are: 1) basic link creation, verify it can be followed 2) chained links, verify it can be followed 3) replace exiting file a with a link, and a link with a link. verify it can be followed 4) create a broken link, verify it can't be followed Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Jean-Jacques Hiblot 提交于
The command line is: ln <interface> <dev[:part]> target linkname Currently symbolic links are supported only in ext4 and only if the option CMD_EXT4_WRITE is enabled. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Jean-Jacques Hiblot 提交于
Re-use the functions used to write/create a file, to support creation of a symbolic link. The difference with a regular file are small: - The inode mode is flagged with S_IFLNK instead of S_IFREG - The ext2_dirent's filetype is FILETYPE_SYMLINK instead of FILETYPE_REG - Instead of storing the content of a file in allocated blocks, the path to the target is stored. And if the target's path is short enough, no block is allocated and the target's path is stored in ext2_inode.b.symlink As with regulars files, if a file/symlink with the same name exits, it is unlinked first and then re-created. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com> [trini: Fix ext4 env code] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Jean-Jacques Hiblot 提交于
There is no need to modify the buffer passed to ext4fs_write_file(). The memset() call is not required here and was likely copied from the equivalent part of the ext4fs_read_file() function where we do need it. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Jean-Jacques Hiblot 提交于
We need to make sure that file writes,file creation, etc. are properly performed and do not corrupt the filesystem. To help with this, introduce the assert_fs_integrity() function that executes the appropriate fsck tool. It should be called at the end of any test that modify the content/organization of the filesystem. Currently only supports FATs and EXT4. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Jean-Jacques Hiblot 提交于
If the metadata checksums are enabled, all write operations will fail. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Stephen Warren 提交于
When a file contains extents, U-Boot currently reads extent-related data for each block in the file, even if that data is located in the same block each time. This significantly slows down loading of files that use extents. Implement a very dumb cache to prevent repeatedly reading the same block. Files with extents now load as fast as files without. Note: There are many cases where read_allocated_block() is called. This patch only addresses one of those places; all others still read redundant data in any case they did before. This is a minimal patch to fix the load command; other cases aren't fixed. Signed-off-by: NStephen Warren <swarren@nvidia.com>
-
-
git://git.denx.de/u-boot-atmel由 Tom Rini 提交于
First set of u-boot-atmel features and fixes for 2019.07 cycle
-
- 09 4月, 2019 24 次提交
-
-
由 Stefan Roese 提交于
I've noticed that the first ethernet packet after PHY link establishment is not tranferred correctly most of the time on my AT91SAM9G25 board. Here I usually see a timeout of a few seconds, which is quite annoying. Adding a small delay (10ms in this case) after the link establishment helps to solve this problem. With this patch applied, this timeout on the first packet is not seen any more. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Wenyou Yang <wenyou.yang@atmel.com> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Claudiu Beznea 提交于
Add slew rate support for SAM9X60 pin controller. Signed-off-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
-
由 Claudiu Beznea 提交于
Add compatibles for SAM9X60 pin controller. Signed-off-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
-
由 Claudiu Beznea 提交于
Add drive strength support for SAM9X60 pin controller. Signed-off-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
-
由 Claudiu Beznea 提交于
SAM9X60 uses high and low drive strengths. To implement this, in at91_pinctrl_mux_ops::set_drivestrength we need bit numbers of drive strengths (1 for low, 2 for high), thus change the code to allow the usage of drive strength bit numbers. Signed-off-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
-
由 Stefan Roese 提交于
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage. This patch adds support for this board including SPL support. Therefore the AT91Boostrap is not needed on this platform any more. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Stefan Roese 提交于
This makes it possible to reference the watchdog DT node via "&watchdog" from board dts files. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Stefan Roese 提交于
This patch adds the necessary defines to the Siemens AT91SAM based boards (smartweb, corvus and taurus) to generate the combined binary image with SPL and main U-Boot image combined (u-boot-with-spl.bin). Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: NHeiko Schocher <hs@denx.de> Tested on the taurus board: Tested-by: NHeiko Schocher <hs@denx.de>
-
由 Stefan Roese 提交于
This patch adds the CONFIG_SPL_IMAGE option to select the SPL image that shall be used to generate the combined SPL + U-Boot image. The default value is the current value "spl/u-boot-spl.bin". This patch also sets CONFIG_SPL_IMAGE to "spl/boot.bin" for AT91 targets which use SPL NAND support (boot from NAND). For these build targets the combined image "u-boot-with-spl.bin" is now automatically generated and can be programmed into NAND as one single image (vs. SPL image and U-Boot as 2 separate images). Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com>
-
由 Stefan Roese 提交于
This patch moves the AT91SAM NAND booting SPL image "boot.bin" which includes the ECC values from the root directory into the spl directory, where all SPL related images are located. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: NHeiko Schocher <hs@denx.de> Tested on the taurus board: Tested-by: NHeiko Schocher <hs@denx.de>
-
由 Stefan Roese 提交于
This patch adds _image_binary_end to the SPL linker script. This will be used be the upcoming GARDENA AT91SAM based platform, which uses DT in SPL and configures CONFIGURE_SPL_SEPARATE_BSS. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Stefan Roese 提交于
This patch enables and starts the watchdog on the AT91 platform if configured. The WD timeout value is read in the AT91 WD device driver from the DT, using the "timeout-sec" DT property. If not provided in the DT, the default value of 2 seconds is used. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com>
-
由 Stefan Roese 提交于
This patch removes the CONFIG_AT91_HW_WDT_TIMEOUT as its not needed any more. The WD timeout value can be provided via the "timeout-sec" DT property. If not provided this way, the default value of 2 seconds will be used. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com>
-
由 Stefan Roese 提交于
This patch fixes the timer register setup in at91_wdt_start() to correctly configure the register again. The input timeout value is now in milli-seconds instead of seconds with the new watchdog API. Make sure to take this into account and only use a max timeout value of 16 seconds as appropriate for this SoC. Also the check against a lower timeout value than 0 is removed. This check makes no sense, as the timeout value is unsigned. Signed-off-by: NStefan Roese <sr@denx.de> Reported-by: NHeiko Schocher <hs@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: NHeiko Schocher <hs@denx.de> Tested on the taurus board: Tested-by: NHeiko Schocher <hs@denx.de>
-
由 Stefan Roese 提交于
This patch adds some checks, so that the watchdog can be enabled in main U-Boot proper but can be disabled in SPL. This will be used by some AT91SAM based boards, which might enable the watchdog in the main U-Boot proper and not in SPL. It will be enabled in SPL by default there, so no need to configure it there. This approach saves some space in SPL. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: NHeiko Schocher <hs@denx.de> Tested on the taurus board: Tested-by: NHeiko Schocher <hs@denx.de>
-
由 Stefan Roese 提交于
This patch adds an alterative SPL version of atmel_serial_enable_clk(). This enables the usage of this driver without full clock support (in drivers and DT nodes). This saves some space in the SPL image. Please note that this fixed clock support is only added to the SPL code in the DM_SERIAL part of this file. All boards not using SPL & DM_SERIAL should not be affected. This patch also introduces CONFIG_SPL_UART_CLOCK for the fixed UART input clock. It defaults to 132096000 for ARCH_AT91 but can be set to a different value if needed. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com>
-
由 Stefan Roese 提交于
This patch adds a call to spl_early_init() to board_init_f() which is needed when CONFIG_SPL_OF_CONTROL is configured. This is necessary for the early SPL setup including the DTB setup for later usage. Please note that this call might also be needed for non SPL_OF_CONTROL board, like the smartweb target. But smartweb fails to build with this call because its binary grows too big. So I disabled it for these kind of targets for now. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: NHeiko Schocher <hs@denx.de> Tested on the taurus board: Tested-by: NHeiko Schocher <hs@denx.de>
-
由 Stefan Roese 提交于
Make sure that lowlevel_init is not compiled when CONFIG_SKIP_LOWLEVEL_INIT_ONLY is configured. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: NHeiko Schocher <hs@denx.de> Tested on the taurus board: Tested-by: NHeiko Schocher <hs@denx.de>
-
由 Ilko Iliev 提交于
Migrate the following options to CONFIG_DM: CONFIG_DM_GPIO CONFIG_DM_MMC CONFIG_DM_ETH CONFIG_DM_SERIAL CONFIG_DM_USB Signed-off-by: NIlko Iliev <iliev@ronetix.at>
-
由 Alexander Dahl 提交于
When introducing the SAMA5D27 SoCs, the SAMA5D2 series got an additional chip id. The check if the cpu is sama5d2 was changed from a preprocessor definition (inlining a call to 'get_chip_id()') to a C function, probably to not call get_chip_id twice? That however broke a check in the macb ethernet driver. That driver is more generic and also used for other platforms. I suppose this solution was implemented to use it in 'gem_is_gigabit_capable()', without having to stricly depend on the at91 platform: #ifndef cpu_is_sama5d2 #define cpu_is_sama5d2() 0 #endif That only works as long as cpu_is_sama5d2 is a preprocessor definition. (The same is still true for sama5d4 by the way.) So this is a straight forward fix for the workaround. The not working check on the SAMA5D2 CPU lead to an issue on a custom board with a LAN8720A ethernet phy connected to the SoC: => dhcp ethernet@f8008000: PHY present at 1 ethernet@f8008000: Starting autonegotiation... ethernet@f8008000: Autonegotiation complete ethernet@f8008000: link up, 1000Mbps full-duplex (lpa: 0xffff) BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 BOOTP broadcast 6 BOOTP broadcast 7 BOOTP broadcast 8 BOOTP broadcast 9 BOOTP broadcast 10 BOOTP broadcast 11 BOOTP broadcast 12 BOOTP broadcast 13 BOOTP broadcast 14 BOOTP broadcast 15 BOOTP broadcast 16 BOOTP broadcast 17 Retry time exceeded; starting again Notice the wrong reported link speed, although both SoC and phy only support 100 MBit/s! The real issue on reliably detecting the features of that cadence ethernet mac IP block, is probably more complicated, though. Fixes: 245cbc58 ("ARM: at91: Get the Chip ID of SAMA5D2 SiP") Signed-off-by: NAlexander Dahl <ada@thorsis.com>
-
由 Eran Matityahu 提交于
Before printk.h was introduced and MTDDEBUG was removed, pr_crit() was calling MTDDEBUG(), which was since then replaced by the current pr_debug(). pr_debug is more appropriate here. Signed-off-by: NEran Matityahu <eran.m@variscite.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Eran Matityahu 提交于
Add a new definition for ubi_assert and keep the original one in an ifndef __UBOOT__. Signed-off-by: NEran Matityahu <eran.m@variscite.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
git://git.denx.de/u-boot-efi由 Tom Rini 提交于
Pull request for UEFI sub-system for v2019.07-rc1 The patch series adds support for the BootNext and BootCurrent variables. The rest is mostly bug fixes. With the bug fixes in place it becomes possible to use the EFI Shell `edit` command. A new unit test is supplied to check the image base and size fields of the loaded image protocol. An inline check when freeing memory from the pool safeguards against double frees.
-
git://git.denx.de/u-boot-riscv由 Tom Rini 提交于
- RISC-V arch support SMP. - Support Andestech's PLIC and PLMT. - qemu, fu54e, ae350 boards enable SMP by default. - Fix CONFIG_DEFAULT_DEVICE_TREE failure.
-