Also rearrange IH_TYPE table slightly.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Add support for SERIAL MULTI for uartlite.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

While adding asm/cache.h to common.h for PPC targets, I got an
error about multiple definitions of some DBSR_ macros. While
scanning these defines, I noticed that some where defined not
correctly for all PPC variants. So I removed all unused defines,
and corrected the ones really used by bedbug (book-e vs. ppc40x).
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>

This is needed for the patch "cache: add default setting for
CONFIG_SYS_CACHELINE_SIZE" from Anton Staaf. As cache.h defines
CONFIG_SYS_CACHELINE_SIZE for PPC targets.

This will remove the following warnings/errors:

include/common.h:819:2: warning: #warning CONFIG_SYS_CACHELINE_SIZE not defined, using __BIGGEST_ALIGNMENT__
cache.c:33: error: '__BIGGEST_ALIGNMENT__' undeclared (first use in this function)
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Anton Staaf <robotboy@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>

Previous output:
Marvell>>  mmc part

Partition Map for MMC device 1  --   Partition Type: EFI

Part  Start LBA  End LBA
gpt1  0x8C00    0xCBFF
gpt2  0xCC00    0x57BFF
gpt3  0x57C00    0xA2BFF
gpt4  0xA2C00    0xECBFDE

With the patch, the output becomes:
Marvell>> mmc part

Partition Map for MMC device 1  --   Partition Type: EFI

Part    Name                    Start LBA       End LBA
  1     ramdisk                 0x00008C00      0x0000CBFF
  2     system                  0x0000CC00      0x00057BFF
  3     userdata                0x00057C00      0x000A2BFF
  4     remaining               0x000A2C00      0x00ECBFDE
Signed-off-by: NLei Wen <leiwen@marvell.com>

mkimage's ublimage support can't depend of build-time board configs;
instead, this should be set in ublimage.cfg.  Since currently no configs
in u-boot override the NAND block size, hardcode it as such in
ublimage.h to fix a build failure with "make tools":
gcc [...] -o ublimage.o ublimage.c -c
In file included from ublimage.c:37:0:
ublimage.h:31:20: fatal error: config.h: No such file or directory

Cc: Heiko Schocher <hs@denx.de>
Cc: patches@linaro.org
Signed-off-by: NLoïc Minier <loic.minier@linaro.org>
Acked-by: NHeiko Schocher <hs@denx.de>

Generate timestamp_autogenerated.h as safely as version_autogenerated.h.

Cc: patches@linaro.org
Signed-off-by: NLoïc Minier <loic.minier@linaro.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Tools such as mkimage include version information but are
config-agnostic; build timestamp_autogenerated.h even when config.mk
isn't generated to fix "make tools" build failure:
gcc [...] -o mkimage.o mkimage.c -c
In file included from include/version.h:27:0, from mkimage.c:26:
include/timestamp.h:27:37: fatal error: timestamp_autogenerated.h: No
such file or directory

Cc: patches@linaro.org
Signed-off-by: NLoïc Minier <loic.minier@linaro.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>

The generated file asm-offsets.s may be found at various depths in the
arch subdirectories, so simply ignore it throughout the tree.
Signed-off-by: NLaurence Withers <lwithers@guralp.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Introduce CONFIG_SPL_START_S_PATH to configure path to start.S file. It's not
always fitting to use CPU's start.S .
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

cmd_sf.c: In function 'do_spi_flash':
cmd_sf.c:164:9: warning: 'skipped' may be used uninitialized in this function
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NSimon Glass <sjg@chromium.org>

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This is long over due.  All but two net drivers have been converted, but
those have now been dropped.

The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined.  So here we scrub the
core code.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This driver was never converted to NET_MULTI, and no board uses it.
So punt it and be done.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

These drivers have never been converted to NET_MULTI, and they are only
used by one board (BMW).  So drop the drivers until someone feels like
rewriting them for NET_MULTI support.

Rather than punting the BMW board completely, just disable net support
in its board config.  Seems to build fine without it.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Now that we've got boards.cfg and most people have converted over,
start warning people who have yet to so we can phase board configs
completely out of the Makefile.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This pushes the ugly duplicated arch ifdef lists we maintain in various
image related files out to the arch headers themselves.
Acked-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The m68k tree is the only one where `./MAKEALL <arch>` does not work.
So rename the existing coldfire list in the MAKEALL script to m68k, and
add an alias from coldfire to m68k.  This makes scripting around MAKEALL
easier.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Some images have not a header of fix lenght. The patch will be
used for the generation of AIS images, because this header has
a variable lenght. The patch adds also the parameter "-s" (skip)
to not copy automatically the passed image file.
Signed-off-by: NStefano Babic <sbabic@denx.de>

Each image handler must return a not-zero velue if the
header is not recognized to allow the main program to
iterate to the next handler.
Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: NHeiko Schocher <hs@denx.de>

The current km_arm boards have a Power-On test jumper. When this
jumper is set, this triggers some Power-On tests on the board.

This patch enables the support of this jumper for starting the
memory_regions test when the jumper is set.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>

This allows to test a larger part of the RAM in the memory tests.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>

This test is similar to the actual POST memory test but quicker and
far less complete. It checks the address and data lines and then only
tests some regularly placed sub regions of the RAM.
This can be useful when we want to test the RAM but we do not have enough
time to run the full memory test.

The POST memory test code was rearranged in order to avoid code duplication
between the two tests but the memory test functionnality remains the same.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Ackey-by: NMike Frysinger <vapier@gentoo.org>

This is needed for a further patch adding a new memory test.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Some boards have the environment variables defined in a slow EEPROM. post_run
accesses these environment variables to define which tests have to be run (in
post_get_flags). This is very slow before the code relocation on some boards
with a slow I2C EEPROM for environement variables.

This patch adds a config option to skip the fetching of the test flags in the
environment variables. The test flags assigned to the tests then only are the
ones statically defined for the test in post/tests.c.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>

The current post_log_word in global data is currently split into 2x
16 bits: half for the test start, half for the test success.
Since we alredy have more than 16 POST tests defined and more could
be defined, this may result in an overflow and the post_output_backlog
would not work for the tests defined further of these 16 positions.

An additional field is added to global data so that we can now support up
to 32 (depending of architecture) tests. The post_log_word is only used
to record the start of the test and the new field post_log_res for the
test success (or failure). The post_output_backlog is for this change
also adapted.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>

The predefinde post_word_load/store functions do not fit all boards,
so we introduce a way to define post_word_load/store as externs in
post.h that then can be defined in board specific files. This is done
with the CONFIG_POST_EXTERNAL_WORD_FUNCS #define
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>

For post to run on ARM, 3 things are needed:
- post_log_word to be defined in gd
- a post.h include in arch/arm/lib/board.c
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Allow redirection of console output prior to console initialisation to a
temporary buffer.

To enable this functionality, the board (or arch) must define:
 - CONFIG_PRE_CONSOLE_BUFFER - Enable pre-console buffer
 - CONFIG_PRE_CON_BUF_ADDR - Base address of pre-console buffer
 - CONFIG_PRE_CON_BUF_SZ - Size of pre-console buffer (in bytes)

The pre-console buffer will buffer the last CONFIG_PRE_CON_BUF_SZ bytes
Any earlier characters are silently dropped.

An entry in the main Makefile for the mx31pdk board is not
necessary, and the board is added to boards.cfg as all
other targets.
Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>

Signed-off-by: NStefano Babic <sbabic@denx.de>

An entry in the main Makefile for the tx25 board is not
necessary, and the board is added to boards.cfg as all
other targets.
Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Tested-by: NWolfgang Denk <wd@denx.de>
Acked-by: NWolfgang Denk <wd@denx.de>

Commit "PPC: Cleanup tqm8xx_pcmcia.c" will clean up the PCMCIA code
to use I/O accessors instead of plain volatile pointer accesses.
This will result in about 300 byte bigger code.  Fix custom linker
script to make room for this.

While we are at it, drop unmaintained u-boot.lds.debug linker script.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Tested-by: NWolfgang Denk <wd@denx.de>

* 'master' of git://git.denx.de/u-boot-nand-flash:
  PPC: Fix socrates NAND problem
  PPC: Fix fsl_upm.c by renaming nand handling functions
  NAND: Make page, erase, oob size available via cmd_nand
  mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi
  NAND: Add -y option to nand scrub command
  NAND: Add nand read.raw and write.raw commands
  NAND: Really ignore bad blocks when scrubbing
  spl, nand: add 4bit HW ecc oob first nand_read_page function
  mxc_nand: fix a problem writing more than 32MB
  mxc_nand: fixed some typos (cosmetic)
  nand: increase chip_delay in mv kirkwood nand driver

* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/p3060: Add SoC related support for P3060 platform
  powerpc/85xx: Add support for setting up RAID engine liodns on P5020
  powerpc/85xx: Refactor some defines out of corenet_ds.h
  fm-eth: Add ability for board code to disable a port
  powerpc/mpc8548: Add workaround for erratum NMG_LBC103
  powerpc/mpc8548: Add workaround for erratum NMG_DDR120
  powerpc/mpc85xxcds: Fix PCI speed
  powerpc/mpc8548cds: Fix booting message
  powerpc/p4080: Add support for secure boot flow
  powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
  powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
  powerpc/p2041rdb: remove watch dog related codes
  powerpc/p2041rdb: updated description of cpld command
  powerpc/p2041rdb: add more ddr frequencies support
  powerpc/p2041rdb: set sysclk according to status of physical switch SW1
  powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
  powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
  powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
  powerpc/mpc8xxx: Add DDR2 to unified DDR driver
  powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
  powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
  powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
  powerpc/85xx: Refactor P2041RDB to use common p_corenet files
  powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
  powerpc/85xx: Enable CMD_REGINFO on corenet boards
  powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
  powerpc/85xx: Fix USB protocol definitions for P1020RDB
  powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
  powerpc/mpc8xxx: Move DDR RCW overriding to common code
  powerpc/mpc8xxx: Extend CWL table
  powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
  powerpc/85xx: Cleanup extern in corenet_ds board code
  powerpc/p2041rdb: Add ethernet support on P2041RDB board
  powerpc/85xx: Add networking support to P1023RDS
  powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
  powerpc/85xx: Add FMan ethernet support to P4080DS
  powerpc/85xx: Add support for FMan ethernet in Independent mode
  powerpc/mpc8548cds: Cleanup mpc8548cds.c
  powerpc/mp: add support for discontiguous cores
  powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
  fdt: Add new fdt_create_phandle helper
  fdt: Rename fdt_create_phandle to fdt_set_phandle
  powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
  fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
  powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
  fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
  powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
  powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
  nand: Freescale Integrated Flash Controller NAND support
  powerpc/85xx: Add basic support for P1010RDB
  powerpc/85xx: Add support for new P102x/P2020 RDB style boards
  powerpc/85xx: relocate CCSR before creating the initial RAM area
  powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
  powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
  powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014

* 'master' of git://git.denx.de/u-boot-i2c:
  I2C: mv_i2c: fix multi-bus init issue
  I2C: mv_i2c: fix build issue when enable debug option

* 'emaclite' of git://git.denx.de/u-boot-microblaze:
  net: emaclite: Use dynamic allocation
  net: emaclite: Remove baseaddress from xemaclite
  net: emaclite: Use calloc instead of malloc
  net: emaclite: Remove deviceid property
  net: emaclite: Change driver name and add address

* 'master' of git://git.denx.de/u-boot-microblaze:
  microblaze: Enable FDT/FIT support
  microblaze: Remove address offset for uart16550
  microblaze: Do not select NFS for platforms without ethernet
  microblaze: Clean up reset asm code
  microblaze: Save and restore first unused vector
  microblaze: Setup MB vectors if feature is enable for u-boot
  microblaze: Remove debug saving value

This reverts commit 60ce53cf.

The commit causes build breakage for a number of boards. This results
from the fact that now the arguments of debug() actually get
referenced (even if there is hope that the compiler will optimize
away the debug() call).  The obvious fix to that probem (change the
code to always declare the referenced variables and data structures)
increases the code size, and was this rejected.  So it was decided to
revert this commit until a better solution is found.