- 15 8月, 2009 1 次提交
-
-
由 Kumar Gala 提交于
When we init the addrmap based on the TLB we will not end up getting the TLB that covers memory if we are using SPD. The reason is we haven't relocated at the point that we setup the memory TLB and thus it will not get setup in the addrmap. Instead we can just walk over the TLB array after we've relocated and see all the TLBs that have been set and use that information to populate the initial addrmap. By doing this we insure that we get the TLB entries that cover memory. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 13 8月, 2009 2 次提交
-
-
由 John Schmoller 提交于
Fix bug introduced by 9c048b52. The cfi_flash.c driver cast the flash buffer size to a uchar in flash_write_cfibuffer(). On some flash parts, (tested on Numonyx part PC32F512M29EWH), the buffer size is 1KB. Remove the cast to uchar to enable buffer sizes to be larger. Signed-off-by: NJohn Schmoller <jschmoller@xes-inc.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Mike Frysinger 提交于
The local board-specific spi_init() function conflicts with the common SPI layer, so rename it to something board-specific. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 12 8月, 2009 6 次提交
-
-
由 Giuseppe CONDORELLI 提交于
This patch adds watchdog reset call to allow its invokation during decompression phase. This control was present on old zlib version and here it is backported for those relevant routines. This patch is sent as a zlib separate one beacuse it was not tested due to specific board lack. zlib patches will be unified just in one when this will be validated through tests. Signed-off-by: NGiuseppe Condorelli <giuseppe.condorelli@st.com>
-
由 Giuseppe CONDORELLI 提交于
This patch updates zlib to the latest stable version. Only relevant zlib parts were ported to u-boot tree, as already did for the current zlib (0.95). New zlib guarantees a faster inflate performances other then others improvements as explained at www.zlib.net. It also includes Alessandro Rubini's patches to allow 0 as destination pointer and to call watchdog reset if required by architecture. Signed-off-by: NGiuseppe Condorelli <giuseppe.condorelli@st.com> Reviewed-by: NAngelo Castello <angelo.castello@st.com> Reviewed-by: NAlessandro Rubini <rubini-list@gnudd.com>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
-
-
-
- 11 8月, 2009 9 次提交
-
-
由 Mark Jackson 提交于
The initial pixclock for the MIMC200 board is wrong (and causes screen corruption due to DMA underruns). This patch simply reduces the pixel clock to fix the problem. Signed-off-by: NMark Jackson <mpfj@mimc.co.uk>
-
由 Richard Retanubun 提交于
Fixed a misunderstanding in the original implementation, 'devnum' that was used in the cpu/ppc4xx/4xx_enet.c implementation was NOT the PHY's SMI address, rather it was the number of the MAC interface on the CPU. The equivalent of this for uec_phy will be the UEC number stored in mii_info->dev->name. Usage example is updated for uec. Signed-off-by: NRichard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Richard Retanubun 提交于
It is set to 0x1F by default and can be overwritten on the board header file by defining CONFIG_UTBIPAR_INIT_TBIPA. This allows the CPU to simply "reserve" one SMI address instead of using a different one for each UEC. Signed-off-by: NRichard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Prafulla Wadaskar 提交于
eth_setenv_enetaddr is avaible by upper layer using this saves 204 bytes on total image size used Local OUI instead of Marvell OUI for random MAC address generation logic Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Roy Zang 提交于
Fix E1000 build warning on AP1000 board Fix the build warning on AP1000 board: e1000.c:131: warning: 'e1000_read_eeprom' used but never defined e1000.c:2012: warning: 'e1000_set_phy_mode' defined but not used Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Sandeep Paulraj 提交于
Due to recent changes to the NET support on U-boot, DM9000 is no longer detected on the DM355 EVM. This minor update enables DM9000 on the DM355 EVM. Tested on the DM355 EVM Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Prafulla Wadaskar 提交于
1. mv88E61xx driver compiler warnings fixed 2. idstr if-else statements changed to switch() construct and added default case too. This fixed idstr may be uninitialized warning Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Po-Yu Chuang 提交于
This patch adds an FTMAC100 ethernet driver for Faraday A320 evaluation board. Signed-off-by: NPo-Yu Chuang <ratbert@faraday-tech.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Kumar Gala 提交于
For some reason the MPC8544 enabled BEDBUG if PCI was enabled and that got copied int the MPC8536, MPC8572 and P2020 DS boards. The BEDBUG support has never been made to work completely on e500/85xx so we just disable it to save space and match the other FSL 85xx boards. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 10 8月, 2009 22 次提交
-
-
由 Wolfgang Denk 提交于
Update CHANGELOG Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
tftp.c:294: warning: pointer targets in passing argument 1 of 'strlen' differ in signedness This was only visible for the utx8245 board which seems to have DEBUG enabled. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Dirk Behme 提交于
Remove bogus config.mk entry, fix newline and remove redundant omap3/config.mk Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Dirk Behme 提交于
Applying two indepenent OMAP3 patches resulted in missing GPMC_CONFIG_CS0_BASE. Patch "omap3: embedd gpmc_cs into gpmc config struct" removes GPMC_CONFIG_CS0_BASE, independent patch "omap3: bug fix for NOR boot support" introduces it's usage. Re-introduce GPMC_CONFIG_CS0_BASE. Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Ilya Yanok 提交于
This is a port of Linux driver for SDHC host controller hardware found on Freescale's MX2 and MX3 processors. Uses new generic MMC framework (CONFIG_GENERIC_MMC) and it looks like there are some problems with a framework (at least on LE cpus). Some of these problems are addressed in the following patches. Signed-off-by: NIlya Yanok <yanok@emcraft.com>
-
由 Alessandro Rubini 提交于
Signed-off-by: NAlessandro Rubini <rubini@gnudd.com>
-
由 Albin Tonnerre 提交于
This chip is used in a number of boards manufactured by Calao-Systems which should be supported soon. This driver provides the necessary spi_read and spi_write functions necessary to communicate with the chip. Signed-off-by: NAlbin Tonnerre <albin.tonnerre@free-electrons.com>
-
由 Prafulla Wadaskar 提交于
It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF for NAND specific warning removal, same is done in this patch Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
-
由 Josh Boyer 提交于
It was brought to our attention that U-Boot contains code derived from the IBM OpenBIOS source code originally provided with some of the older PowerPC 4xx development boards. As a result, the original license of this code has been carried in the various files for a number of years in the U-Boot project. IBM is dual-licensing the IBM code contributions already present in U-Boot under either the terms of the GNU General Public License version 2, or the original code license already present. Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
-
由 Kumar Gala 提交于
If the size of a region equal to 4G it can't be represnted in a 32-bit BAR so we should have marked that case as MEM64. Additionally bump the number of inbound windows up to 4 to handle the fact that Freescale PPCs that have an implicit window for CCSRBAR. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Wolfgang Denk 提交于
The ARM EABI defines new names for GCC helper functions, and GCC seems to need some new functions as well. This patch is a minimal-invasive approach to fix problems with EABI conformant tool chains (to be used with "USE_PRIVATE_LIBGCC=yes"). Signed-off-by: NWolfgang Denk <wd@denx.de> Tested-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Peter Tyser 提交于
An off-by-one error in hush.c resulted in an unintentional free() call every time a command was executed Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
-
由 Detlev Zundel 提交于
Signed-off-by: NDetlev Zundel <dzu@denx.de>
-
由 Detlev Zundel 提交于
While at it, remove initialization of variables which will be set before usage in all cases. Signed-off-by: NDetlev Zundel <dzu@denx.de>
-
由 Anatolij Gustschin 提交于
Add mtc state subcommand description to the help of mtc command. Remove some newlines in description of commands for proper help formating. Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Grzegorz Bernacki 提交于
Signed-off-by: NGrzegorz Bernacki <gjb@semihalf.com>
-
由 Wolfgang Denk 提交于
Remove bogus newline character that got added to the .name field of the disk_partition_t structure. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Luigi 'Comio' Mantellini 提交于
Signed-off-by: NLuigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
-
由 Jens Scharsig 提交于
Signed-off-by: NJens Scharsig <esw@bus-elektronik.de>
-
由 Mike Frysinger 提交于
The only environment type that uses this variable is spi flash, and that is only because it is reimplementing the common set_default_env() function. So fix the spi flash code and kill off the default_environment_size in the process. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
While we're here, fix the broken #ifdef handling in _exports.h. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-