- 27 11月, 2017 3 次提交
-
-
由 Fabio Estevam 提交于
imx_set_wdog_powerdown() is always used to disable the power down enable bit, so remove the boolean parameter of the function. It is also a bit strange to write a boolean value into registers, so this new version makes explicit that we are writing 0. While at it, rename it to imx_wdog_disable_powerdown(). Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Fabio Estevam 提交于
Clear powerdown enable bit for WDOG3 on i.MX6ULL to avoid unwanted kernel reboots. Suggested-by: NYe Li <ye.li@nxp.com> Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NPeng Fan <peng.fan@nxp.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Fabio Estevam 提交于
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this into account in the base address definition. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NPeng Fan <peng.fan@nxp.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
- 20 11月, 2017 17 次提交
-
-
由 Fabio Estevam 提交于
SPL option is already selected via Kconfig, so remove it from the CONFIG_SYS_EXTRA_OPTIONS line. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Fabio Estevam 提交于
Currently the MX6QDL option is selected via CONFIG_SYS_EXTRA_OPTIONS, but it is better to select it directly via Kconfig. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Peter Senna Tschudin 提交于
Create board support for GE PPD, based on mx53loco. Use mx53ppd_defconfig make target to configure for this board. Signed-off-by: NPeter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: NIan Ray <ian.ray@ge.com> Signed-off-by: NNandor Han <nandor.han@ge.com> Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk> Cc: Stefano Babic <sbabic@denx.de> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Martyn Welch 提交于
The VPD data is used on a number of GE products. Move the parsing code to a common location so that we can share this code. Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Nandor Han 提交于
Add support for S35392A RTC. The driver supports both U-Boot driver models. Signed-off-by: NNandor Han <nandor.han@ge.com> Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk> Cc: Heiko Schocher <hs@denx.de>
-
由 Ian Ray 提交于
Add support for bootcounter on an EXT filesystem. Sync configuration whitelist. Signed-off-by: NIan Ray <ian.ray@ge.com> Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
-
由 Martyn Welch 提交于
Add register definitions require for video configuration. Signed-off-by: NNandor Han <nandor.han@ge.com> Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk> Reviewed-by: NStefano Babic <sbabic@denx.de> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Martyn Welch 提交于
Add missing parts for i.MX53 PWM support Acked-by: NNandor Han <nandor.han@ge.com> Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk> Cc: Stefano Babic <sbabic@denx.de> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Ian Ray 提交于
Some fixes when reading EXT files and directory entries were identified after using e2fuzz to corrupt an EXT3 filesystem: - Stop reading directory entries if the offset becomes badly aligned. - Avoid overwriting memory by clamping the length used to zero the buffer in ext4fs_read_file. Also sanity check blocksize. Signed-off-by: NIan Ray <ian.ray@ge.com> Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
由 Nandor Han 提交于
Tweak the i2c transfer to work for devices that want to read data without addressing a register. Signed-off-by: NNandor Han <nandor.han@ge.com> Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk> Acked-by: NHeiko Schocher <hs@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
由 Fabio Estevam 提交于
This reverts commit b8b9790e. Some wandboard variants no longer boot after this commit, so keep the original delay to avoid the boot regression. Reported-by: NVarga Zsolt <vazso@vazso.hu> Tested-by: NVarga Zsolt <vazso@vazso.hu> Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Fabio Berton 提交于
Signed-off-by: NFabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
-
由 Fabio Berton 提交于
Command run setup_emmc will create gpt partitions for mmc 0 device based on patitions variable. Signed-off-by: NFabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
-
由 Fabio Berton 提交于
Create layout with a boot 16MiB partition and rootfs with remain space. Signed-off-by: NFabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Fabio Berton 提交于
Change dfu_alt_info variable to use the following altsetting: uboot: To flash raw U-Boot /zImage: boot: To copy kernel image /imx6ul-pico-hobbit.dtb: To copy dtb file rootfs: To copy rootfs List the currently attached DFU capable USB devices running: sudo dfu-util -l Flash U-Boot: sudo dfu-util -D u-boot.imx -a uboot Copy boot files: sudo dfu-util -D zImage -a /zImage sudo dfu-util -D imx6ul-pico-hobbit.dtb -a /imx6ul-pico-hobbit.dtb Flash rootfs: sudo dfu-util -D rootfs.ext4 -a rootfs To copy boot files you need to have a formated mmc 0:1 partition. To format with ext4 filesystem you can use ums. Run on target: ums 0 mmc 0 and on host: sudo mkfs.ext4 /dev/sdx1 Signed-off-by: NFabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
-
由 Fabio Berton 提交于
Currently the rootfs location is passed via mmcblk number and using the UUID method to specify the rootfs location is a better approach working even if mmcblk number for the eMMC changes depending on the kernel versions. Signed-off-by: NFabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Fabio Berton 提交于
Create CONFIG_DFU_ENV_SETTINGS to set dfu environment settings to improve human readable code. Signed-off-by: NFabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br> Reviewed-by: NLukasz Majewski <lukma@denx.de>
-
- 16 11月, 2017 1 次提交
-
-
由 Marek Vasut 提交于
The board uses T-topology for the four x16 DRAM chips, so remove the write-leveling from the SPL as that is only usefly on fly-by topology and can be harmful on T-topology. Also update the DRAM timing with values from calibration on multiple boards. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
- 14 11月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 13 11月, 2017 3 次提交
-
-
由 Soeren Moch 提交于
This reverts commit c61d0009. A tbs2910 board user reported a very slow console frambuffer as regression in current u-boot. I could bisect this down to the above mentioned commit. This revert brings back the fast framebuffer console (one cache flush per string in puts(), not after each char). Reported-by: NUwe Scheffler <scheffler.u@web.de> Signed-off-by: NSoeren Moch <smoch@web.de> Tested-by: NUwe Scheffler <scheffler.u@web.de> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Angelo Dureghello 提交于
Signed-off-by: NAngelo Dureghello <angelo@sysam.it>
-
由 Marek Vasut 提交于
The eMMC is 1V8 device only and the signaling is always 1V8, fix the DT for Salvator-X/XS to describe the hardware correctly. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 10 11月, 2017 7 次提交
-
-
-
由 Werner Böllmann 提交于
After updating u-boot from v2016.01 to 2017.09, issue with "SATA link 0 timeout." on my Cubietruck board. mdelay milled after moving satapwr code to board. "sunxi: Turn satapwr on from board_init" (sha1: 9fbb0c3a) After adding the "mdelay(500);" line that was lost in the path the error is gone. Signed-off-by: NWerner Böllmann <Werner.Boellmann@fh-dortmund.de> [Rebased and updated change and commit message] Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Chen-Yu Tsai 提交于
Only the H3/H5 SoCs have an internal PHY and its related clock and reset controls. Use an #ifdef to guard the internal PHY control code block so it can be built for other SoCs, such as the A83T or A64. Signed-off-by: NChen-Yu Tsai <wens@csie.org> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: NJoe Hershberger <joe.hershberger@ni.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
-
由 Jagan Teki 提交于
Update the falcon offsets for args to 16MB and kernel to 17MB Since the below commit updated U-Boot proper location along with rockchip boot image offsets "spl: set SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x4000 for rockchip" (sha1: 8f4d62b4) Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Jagan Teki 提交于
This patch fixed U-Boot proper location has been missed to update in bewlo commit "rockchip: doc: update U-Boot location info" (sha1: 73e6dbe8) Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Goldschmidt Simon 提交于
The U-Boot location has been moved to block 16384. This is 8MB, not 4MB. Signed-off-by: NSimon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com> Reviewed-by: NJagan Teki <jagan@openedev.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
- 09 11月, 2017 8 次提交
-
-
-
-
由 Lukasz Majewski 提交于
Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
This commit provides support for LWN's IMX6Q based DISPLAY5 board. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
This commit provides generic function to set the RGMII/HSIC IO voltage level on iMX6 devices. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
The sys_proto.h file has been included earlier in this file. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-