Uncompressed aarch64 kernel Image are rather large, increase the bootm
size limit to 64 MiB to cater for that.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com>

Now that usb host is supported let's enable it on this board.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Enable usbotg1 port node as host usb.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Usb is now supported so add all required nodes for it in imxrt1050.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Add support for usb1 and usb2 present on i.IMXRT.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Usb needs IMXRT1050_CLK_USBOH3 clock to be enabled, so let's add it to
clock driver.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

We need those macros to instruct drivers on how to behave for SoC specific
quirks, so let's add it as done for other i.MX SoCs.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

i.MXRT1020 supports gpio5, so let's add a node for it.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

At the moment a lot of u-boot,dm-spl properties are present in board .dts
file but this is not correct since u-boot,dm-spl property is u-boot
specific and must be listed into the separate imrt1020-evk-u-boot.dtsi
file. So let's move every u-boot,dm-spl property present in
imxrt1020-evk.dts to imxrt1020-evk-u-boot.dtsi file.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

At the moment a lot of u-boot,dm-spl properties are present in board .dts
file but this is not correct since u-boot,dm-spl property is u-boot
specific and must be listed into the separate imrt1050-evk-u-boot.dtsi
file. So let's move every u-boot,dm-spl property present in
imxrt1050-evk.dts to imxrt1050-evk-u-boot.dtsi file.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

We don't need lcdif to be enable in SPL, so let's remove u-boot,dm-spl.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Lcdif needs both "pix" and "axi" clocks to be enabled so let's add them to
lcdif node.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Since we assume pll5 is the default lcdif clock source let's move
assigned-clocks(-parents) properties to .dtsi file.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Lcd peripheral needs 2 different gates to be enable to work, so let's
introduce the missing one(LCDIF_PIX) and rename the existing one
(LCDIF_APB).
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Some SoC needs "disp_axi" clock to be enabled, so let's try to retrieve it
and enabling. If it fails it gives only a debug(), but this clock as well
as "axi" clock is not mandatory.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

On some SoC mxsfb needs more than one clock gate(actual "per" clock). So
let's introduce "axi" clock that can be provided but it's not mandatory.
This is inspired from linux mxsfb driver. Also let's rename "per" clock to
"pix" clock for compatibility with already existing .dts lcdif nodes
implementation.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Let's enable imx-gpt-timer in imx1050-evk defconfig.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Now device_type = "memory" is mandatory to allow u-boot to read memory
node, so let's add it to memory node.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Timer needs to be already enabled in spl, so let's add its node to spl dtb.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Let's set gpt1 as u-boot timer.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Enable gpt1 timer.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Add gpt1 node for using it as timer.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Let's add node label to osc to be used as clock source for other nodes.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Let's enable imx-gpt-timer in imx1020-evk defconfig.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Now device_type = "memory" is mandatory to allow u-boot to read memory
node, so let's add it to memory node.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Timer needs to be already enabled in spl, so let's add its node to spl dtb.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Let's set gpt1 as u-boot timer.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Enable gpt1 timer.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Add gpt1 node for using it as timer.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

Let's add node label to osc to be used as clock source for other nodes.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

This timer driver uses GPT Timer (General Purpose Timer) available on
a lot of i.MX SoCs family. This driver deals with both 24Mhz oscillator
as well as peripheral clock.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>
[Giulio: added the driver's stub and handled peripheral clock prescaler
setting making driver to work correctly]
Signed-off-by: NJesse Taube <mr.bossman075@gmail.com>
[Jesse: added init, setting prescaler for 24Mhz support and enabling
timer]

This mpu handling works for every i.MXRT SoC that we have, so let's
generalize imxrt1050_region_config to imxrt_region_config.
Signed-off-by: NGiulio Benetti <giulio.benetti@benettiengineering.com>

- More pinctrl updates

Synchronize R-Car Gen2/Gen3 pinctrl tables with Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12") . This is a rather large
commit, since the macros in sh-pfc.h also got updated, so
all the PFC tables must be updated in lockstep.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>

Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Minor fixes for sandbox and handling of dm-ranges

 - disable legacy video for brxre1, mx28evk, pico-imx6ul,
   pxm2 and rut boards after DM_VIDEO conversion deadline

Add a test of dev_read_resource with translation or without translation
Signed-off-by: NPatrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>